Fostex VM08 Setup method of the AUX Send level, Example Character section when E1 is lit

Page 16

Model VM08 Owner’s Manual

1.Status display section [E1] or [E2] dots are lit by pressing the EFF/AUX key.

The LCD will display the following:

Example: Character section when [E1] is lit.

[1-Eff1:00] is displayed. Channel 1 EFFECT SEND 1 level can now be adjusted. The present EFFECT SEND 1 level setting is "dry" (0).

Lit

2.Select the channel to be adjusted by pressing the desired CH ON/CH SEL key.

3.Adjust the number with the DATA encoder.

The number will change in a [0] ~ [99] range and the depth of effects will also change. The graphic display will change at the same time.

[00]~ [99] will be displayed.

Bar graph extends in step by blinking.

<Useful information!>

If channels 5/6 or 7/8 are selected, the two channels will be set at the same time. If MAS- TER is selected, the effect send level master can be adjusted and the L, R meter used to indicate the level.

Setup method of the AUX SEND level

Adjusting the signal level output from the VM08 rear panel AUX SEND jack (1/2).

The adjusted signal is sent to external equipment (external effects and monitor amplifier) from the AUX SEND jack. The same as with the EFFECT SEND signal, either POST or PRE can be selected for the AUX SEND signal. The VM08 is set to POST in the initial state. To change the setting, please see below [Setup of PRE/POST].

1.Light up the [A1] or [A2] dots in the status display section but pressing the EFF/AUX key.

The LCD will display the following:

Example: The character display section with light up [A1].

[1-Aux1:00] is displayed. Now, channel 1 AUX SEND 1 level can be adjusted. This also indicates that the present AUX SEND 1 level setting is MIN (00).

3.Adjust the number with the DATA encoder.

The number will change in the [0] ~ [99] range and depth of effects will also change. The graph- ics display will change at the same time.

[00]~ [99] will be displayed.

Lit

Bar graph extended in step with blinking.

2.Press the desired CH ON/CH SEL key and select the channel you wish to adjust.

<Useful information!>

When channels 5/6 or 7/8 are selected, the two channels will be set at the same time. If MAS- TER is selected, the effect send level master can be adjusted and the L, R meter used to display the level.

16

Image 16

Contents Model Safety Instructions Table of Contents Names and Functions Contrast adjusting knob Status indicatorFader adjust key Level adjust keyReset of VM08 Internal battery for the memory back upRemove the insulation paper Please remember thisPeripheral Equipment Connection ST.OUT L, R jackInput 1 ~ 4 jacks Input 5/6 Input 7/8 jacksInput 5/6, Input 7/8 jacks Input 5/6 7/8 and AUX Send 1/2 jacksAUX Send OUT 1/2 jack Application Example Example-2 To use as a Mono IN/STEREO OUT effectsExample-3 For use as a sub-mixer for a live keyboard player Example-4 To use as a small facility mixerExample-5 For one take live studio recording Example-6 To produce original RemixExample-7 To do you own Sound Track Video Editing Example-8 As a practice aid for your musical instrumentsVM08 Initial State Normal Mix Mode Useful informationCharacter display section Master fader display sectionTo return to the setting before switching off power Setting before switch off of powerMute of the various input channel/master output To set to the present fader positionSetup method for PAN setting Channel Parameter Edit ModeNumber is adjusted with the Data encoder Setup method for EQ setting Setup method of the Effect Send levelExample Character display section when LO is made to light Number is set with the Data encoderExample Character section when E1 is lit Setup method of the AUX Send levelExample The character display section with light up A1 PRE/POST setup method for Effect SEND/AUX Send Example The character display section with E1 is litEffect Edit Mode P. Fostex Advanced Signal Processing TechnologyEffect types preset for EFF About the effect typesWhen the EFF 1 key is pressed When the EFF 2 key is pressedSelecting the effect type Use the Data encoder to select the effect typeEffect parameter settings To cancel mutingMuting an effect To mute the effect soundEffect parameter details Delay pitch effect parameters parameter type Delay Pitch Doubling effect parameters parameter type DoublingChorus effect parameters parameter type Chorus Flanger effect parameters parameter type FlangeScene Memory Mode Storing a scene memoryRecalling a scene memory Press the Scene Store keyLevel adjust Fader adjustPress the Level Adjust key Press the Fader Adjust keyDirectly recalling a scene memory Clearing a scene memoryHold down the Exit key and press the Scene Recall key Press the EFF 1 key or EFF 2 keyMaking settings in setup mode Setup ModeDetails of the setup menu Fader Fix setting Display FaderFix ? Channel fader recall setting Display ChFdrRcl ?Master fader recall setting Display MsFdrRcl ? Foot Switch setting Display Foot Sw ?Specifications Input 1 ~Input 5/6 ~ 7/8 AUX Send 1/2Declaration of EC Directive