Korg D3200 owner manual 2d. EQ/ATT/PHASE, 107, 2d-1. EQ/ATT, 2d-2. EQ Library

2d. EQ/ATT/PHASE

Here you can adjust the equalizer, attenuator, EQ library, and phase settings for each channel, and adjust the master EQ settings.

2d-1. EQ/ATT

For each channel you can edit the settings of the four-band equalizer and the attenuator. The equalizer is normally a peaking type, however the LOW EQ and HIGH EQ bands can be set to a shelving (Shlv) type.

Channels 24–32 and the sub mixer channels have a two-band shelving EQ.

Use the Knob Matrix to select and edit the four EQ bands.

Equalizer settings used here can be loaded from the EQ li- brary, or registered in the EQ library (see the section below, “2d-2. EQ Library”).

1

2 10

11

3

4

5

12

6	7	8	9
1. CH			[1…32]

Click the edit cell that indicates the channel whose EQ you will edit, and use the value dial (or +/– keys) to select the desired channel.

Alternatively, you can press the CH SELECT key and then press a channel key to select the desired channel. This channel is linked with “CH” in the “EQ Library” tab page.

If the selected channel’s PLAY/REC status is PLAY, the screen will show the PlayEQ. If REC, it will show the RecEQ.

2.IN/TR indicator

This indicates either IN or TR to show whether the cur- rent EQ is the PlayEQ or the RecEQ, and also shows the current input source.

3.EQ curve graph

A graphic representation of the EQ curve is shown here.

4. ATT [–63.5 dB…0 dB]

Here you can adjust the attenuator. Lowering this value will lower the level that is input to the EQ.

5.Level meter button

Each time you click the button, the position of the dis- played level meter will change.

IN: Input level. The level input to the EQ is displayed.

PRE: Pre-fader level. The output level of the EQ is dis- played.

PST: Post-fader level. The level after passing through the fader is displayed.

6.LOW G/F/Q

[–15 dB…+15 dB/21 Hz…20 kHz/0.1…10, Shlv]

Here you can adjust the gain, center frequency, and Q (fil- ter sharpness) of the low-frequency region.

If you select Shlv as the Q value, this will become a shelv- ing-type EQ; in this case the F value will be the cutoff fre- quency.

7. LOW-MID G/F/Q

[–15 dB…+15 dB/21 Hz…20 kHz/0.1…10]

Here you can adjust the gain, center frequency, and Q (fil- ter sharpness) of the low-mid frequency region.

8. HIGH-MID G/F/Q

[–15 dB…+15 dB/21 Hz…20 kHz/0.1…10]

Here you can adjust the gain, center frequency, and Q (fil- ter sharpness) of the high-mid frequency region.

9. HIGH G/F/Q

[–15 dB…+15 dB/21 Hz…20 kHz/0.1…10, Shlv]

Here you can adjust the gain, center frequency, and Q (fil- ter sharpness) of the high-frequency region.

If you select Shlv as the Q value, this will become a shelv- ing-type EQ; in this case the F value will be the cutoff fre- quency.

10.FLAT

Sets the Gain of each equalizer band to 0 dB. The EQ set- tings for that channel will be initialized.

11.ON/OFF

Switches the equalizer on/off. This allows you to listen to the signal with and without EQ quickly to check your set- tings.

12. buttons

Use these up/down buttons to edit the parameter values.

2d-2. EQ Library

Here you can load EQ settings from the EQ library. You can also store EQ settings into the User area of the EQ library. There are 50 preset EQ setting programs, and 50 user EQ set- ting programs.

An EQ setting program stores parameters 6–9 of the preced- ing section “2d-1. EQ/ATT.”

2

1

3

4

5

1.EQ library list

Click on the list to select an EQ setting program. The list shows the EQ setting program number (P** are presets, U** are user) and its name.

2. CH [1…16]

Click the edit cell that indicates the channel into which you will recall (or from which you will store) an EQ library item, and use the value dial (or +/– keys) to select the desired channel. Alternatively, you can press the CH SELECT key and then press a channel key to select the desired channel.

This channel is linked with “CH” of the “EQ/ATT” tab page.

3.EQ curve graph

The EQ curve of the selected EQ program is shown as a graph.

4.Recall

Loads the selected EQ program into the channel you selected in 2. “CH.”

Click the library list to select the EQ program that you want to load.

Counter	Rename
METER
MIXER
CH	VIEW
EFFECT
SEND
EQ
PAN
SONG
SYSTEM	/MIDI
TRACK
CD

Reference
	UNDO
	TUNER
	SESSION	DRUMS
	STORE	SCENE
	MARK
	SCRUB
	1/IN ...	4/END
	LOC	LOC
	REC/PLAY	MODE
	Transport	keys

107