Korg D3200 owner manual Disc At Once, Album CD Project, Write the song, Finalize the disc

Make sure that “Free” shows a duration that is longer than the song you want to write.

(4)

(4)

(7)

(5)

(5)Write the song.

•Click the Write To CD button to display the WriteToCD dialog box.

• Select the writing speed.

You must use a disc that supports the selected writing speed.

•A message of “Obey Copyright Rules” will appear.

Read the owner’s manual section “COPYRIGHT WARNING” (→p.iii), and click the Yes button (or press the panel YES key) if you accept the terms.

If the selected song is 24-bit, click the Dither button to turn it on if you want dithering to be performed.

• The D3200 will begin creating an image file.

The data will be written to CD as a 44.1 kHz song. If you se- lect a song whose sampling rate is other than 44.1 kHz, the data must be converted, and a certain amount of time will be required for the conversion to be performed before the song ap- pears in the track list.

You can abort creation of the image file by clicking the Cancel button.

•When the image file has been created, the D3200 will begin writing it to disc.

•When writing is completed, the display will indicate “Completed.” If you want to create another disc with the same data, click the Yes button (or press the panel YES key). Otherwise, click the No button (or press the panel NO key) to proceed to the next step.

If you create another disc with the same data, the process will take less time since the image file has already been created.

(6)If you want to write another song to the CD, repeat steps (2) through (5).

Each additional song will be written to CD following the end of the previously written song(s) on the disc.

(7)Finalize the disc.

When you are finished writing songs to this CD, and want to be able to play the disc on an audio CD player, click the Finalize button to finalize the disc. A message will ask you for confirmation. If you are sure you want to finalize the disc, click the Yes button (or press the panel YES key).

Once a disc has been finalized, no further songs can be added to it. In other words, you should finalize a disc only after you have written all the songs that you intend to write to it.

(8)When finalization is completed, the CD-R/RW drive tray will open.

The LCD screen will indicate “Completed.” Click the OK button (or press the panel YES key) to return to the CD page.

(9)Check the CD by playing it on an audio CD player. Play the CD on an audio CD player to verify that your audio CD was created correctly.

2. Disc At Once

2-1. Album CD Project

If you use Album CD Project to create a CD, you can specify the amount of silence (blank space) between each track, and assign marks for each song to specify the beginning of each track.

In addition, since this method writes the CD using Disc At Once, the audio CD you create can be used as a master CD for pressing.

You can create one Album CD Project for each song drive, and can also back up the data to CD-R/RW (→p.83).

If you use Album CD Project to write a disc, no additional data can be written to that disc.

When you create an Album CD Project, new audio data for writ- ing will be created; this will occupy additional hard disk space.

Even if you delete the original songs, the Album CD Project audio data will not be deleted.

Songs you have created

Song	Song	Song	Song	Song
A	B	C	D	E

Select the songs, specify their order, and adjust the gaps

Song	Song		Song
A	E		D
Trk1	Trk2		Trk3
Post-	Pre-	Post-	Pre-
gap	gap	gap	gap

Write all songs at once

Song	Song	Song
A	E	D	Un-writable area
Trk1	Trk2	Trk3

Blank space according to the gaps you adjusted

(1)Collect all the songs you want to use for the Album CD Project into a single song drive (→p.41).

(2)Select the song drive.

Press the CD key, click the Album CD button in the screen to access the Album CD Project dialog box, click the Drive button, select the song drive that contains the song you want to write, and click the and click the OK button (or press the panel YES key) to confirm.

80