Korg D3200 owner manual 153, Early Reflection, C/R Delay, Stereo/Cross Delay

Page 163

EQ Trim

–15...+15dB

 

Sets the equalizer trim level

LEQ Gain (Pre LEQ Gain)

–15...+15dB

 

Sets the gain of Low EQ

 

 

HEQ Gain (Pre HEQ Gain)

–15...+15dB

 

Sets the gain of High EQ

 

 

P.DlyThru (Pre Delay Thru)

0...100%

Sets the mix ratio of non-delay sound

Rev Level (Reverb Level)

0...100%

 

Sets the reverberation level

 

 

ER Level

0...100%

 

Sets the level of early reflections

: ER Level, : Reverb Level

These parameters set the early reflection level and reverb level. Changing these parameter values allows you to simulate the type of walls in the room. That is, a larger “ER Level” simulates a hard wall, and a larger “Reverb Level” simulates a soft wall.

7: Early Reflection

This effect is only the early reflection part of a reverberation sound, and adds presence to the sound. You can select one of the four decay curves.

Type

Sharp, Loose, Modulated, Reverse

Selects the decay curve for the early reflection

ER Time

10...800msec

 

Sets the time length of early reflection

 

 

Predly (Pre Delay)

0...200msec

Sets the time taken from the original sound to the first early reflection

EQ Trim

–15...+15dB

 

Sets the equalizer trim level

 

 

LEQ Gain (Pre LEQ Gain)

–15...+15dB

 

Sets the gain of Low EQ

HEQ Gain (Pre HEQ Gain)

–15...+15dB

 

Sets the gain of High EQ

 

 

Dry:Wet

Dry, 1:99...99:1, Wet

Sets the balance between the effect and dry sounds

: Type

This parameter selects the decay curve for the early reflection.

8: L/C/R Delay

This multitap delay outputs three Tap signals to the left, right, and center respectively. You can also adjust the left and right spread of the delay sound.

L Time (L Delay Time)

0...2.730sec

 

Sets the delay time of TapL

 

 

C Time (C Delay Time)

0...2.730sec

 

Sets the delay time of TapC

 

 

R Time (R Delay Time)

0...2.730sec

 

Sets the delay time of TapR

Dry:Wet

Dry, 1:99...99:1, Wet

Sets the balance between the effect and dry sounds

 

 

L LevelL (Delay Level)

0...100%

 

Sets the output level of TapL

 

 

C LevelC (Delay Level)

0...100%

 

Sets the output level of TapC

R LevelR (Delay Level)

0...100%

 

Sets the output level of TapR

 

 

Spread

0...100%

Sets the width of the stereo image of the effect sound

 

 

Fdback (C) (Feedback (C Delay))

–100...+100%

Sets the feedback amount of TapC

Fb.LoDamp (Feedback Low Damp)

THRU, 21Hz...8.00kHz

Sets the damping amount in the low range

Fb.HiDamp (Feedback High Damp)

53Hz...20.0kHz, THRU

Sets the damping amount in the high range

 

 

In Level (Input Level)

0...100%

Sets the input level to the effect

: High Damp, : Low Damp

These parameters set the damping amount of high range and low range. The tone of the delayed sound becomes darker and lighter as it feeds back.

: Spread

This parameter sets the pan width of the effect sound. The stereo image is widest with a value of “50,” and the effect sound of both channels is output from the center with a value of “0.”

9: Stereo/Cross Delay

This is a stereo delay, and can by used as a cross-feedback de- lay effect in which the delay sounds cross over between the left and right by changing the feedback routing.

L Time (L Delay Time)

0...2.730sec

 

Sets the left delay time

 

 

R Time (R Delay Time)

0...2.730sec

 

Sets the right delay time

Type (Stereo/Cross)

Stereo, Cross

Switches between stereo delay and cross-feedback delay

 

 

Dry:Wet

Dry, 1:99...99:1, Wet

Sets the balance between the effect and dry sounds

 

 

L Fdback (L Feedback)

–100...+100%

Sets the feedback amount for the left channel

R Fdback (R Feedback)

–100...+100%

Sets the feedback amount for the right channel

 

 

LoDamp (Low Damp)

THRU, 21Hz...8.00kHz

Sets the damping amount in the low range

 

 

HiDamp (High Damp)

53Hz...20.0kHz, THRU

Sets the damping amount in the high range

Spread

0...100%

Sets the width of the stereo image of the effect sound

 

 

In Level (Input Level)

0...100%

 

Sets the input level to the effect

10:St. Multitap Delay (Stereo Multitap Delay)

The left and right Multitap Delays have two taps respective- ly. Changing the routing of feedback and tap output allows you to create various patterns of complex effect sounds.

Tap1Time

 

0...2.730sec

 

 

Sets the delay time of Tap1

 

 

 

Tap2Time

 

0...2.730sec

 

 

Sets the delay time of Tap2

Type

Normal, CrossFdback, CrossPan1, CrossPan2

 

Switches the left and right delay routing

 

 

 

Dry:Wet

 

Dry, 1:99...99:1, Wet

 

Sets the balance between the effect and dry sounds

 

 

 

Tap1Level

 

0...100%

 

 

Sets the output level of Tap1

Tap2Level

 

0...100%

 

 

Sets the output level of Tap2

 

 

T1.Fdback (Tap1 Feedback)

–100...+100%

 

 

Sets the Tap1 feedback amount

 

 

 

Spread

 

0...100%

 

Sets the width of the stereo image of the effect sound

 

Algorithm list

 

 

Program list

 

 

 

 

 

 

 

 

 

 

 

 

Stereo type

Algorithm

 

 

 

 

Monaural type

Algorithm

 

 

 

 

Effect

153

Image 163
Contents Page Important Safety Instructions Data handling Handling of the internal hard diskIii Printing conventions in this Manual RW driveTable of Contents Effects MixerSession Drums Recorder ViiData Viii ReferenceAppendices More about drives and files 171 Specifications 174Various lists 176 Included items Before using the D3200 for the first timePower on/off Power-onPower-off Setting the calendarPress the SYSTEM/MIDI key Click the Control tab Connection example Main features Parts and their function Functions LCD screenInput Mixer scene memories, plus Midi control of mixer parameters Main featuresTrack digital multi-track recorder Session DrumsIntuitive interface designed for ease-of-use CD-R/RW drive for creating backup disk and audio CDsWhat is ? Sophisticated digital editing toolsInput 1, Input 2...INPUT 12 jacks Phantom power switchParts and their function Top panel60 -40 dBu mic input Solo key 13 1-16 key, 17-32 key14 REC/PLAY key CH on keyMark key Direct keysKnob Matrix Scrub keyOn key, standby indicator LOOP, TRIGGER, Auto Punch indicators37 REC/PLAY Mode keys 40 HDD/CD access and Midi indicatorsRear panel About the CD-R/RW drive View Items and functions in the LCD screenRadio buttons List buttonScroll bar/scroll buttons Confirmation buttonSelecting and setting parameters Selecting the page modeBasic operation Selecting a channel Switching between channels 1-16Send and equalizer Editing effectsExamples of operation Connections ConnectionsTurn the D3200 on Please note the following items before you beginWhen the demo song ends, press the Stop key Adjust the mixListen to the demo song Create the song Press the Song key to access the SongCreate a new song Name the songConnect a guitar to the guitar input Connect your audio sources to the mixer inputsConnect mics and instruments to the Input jacks Confirm the changesAssign the inputs to channels Adding EQ and Effects Press the EQ key to access the EQ/ATT tab Choose a channelUse the Knob Matrix to adjust the EQ Adjust the EQ settings of channelChoose an effect program Reverb&Delay in the MonoApplying effects to the input sound Choose an effect typeNormal Select the recording status Setting the recording modeRecording Preparations for recordingStart recording PlaybackArm track 2 for recording OverdubbingApplying effects and EQ to individual channels Press the EQ key to access the EQ/ATT tabApplying EQ to each channel/track Select an effect program Adjusting the panSelecting a master effect Select a track for EQAdjust the return form the master effects Adjusting the Master Effect 1 Send amount for each trackChecking and adjusting the master effect Adjust the send amount of each trackChoose a final effect Make the desired adjustments, and then press the Stop keySet the meters to display the post fader levels Applying an effect to the master bus Final EffectApplying EQ to the master bus Master EQ When you‘re done adjusting the master EQ, press the Stop keyArm the master track for recording Adjust the recording levelRecording the master track Specify a virtual trackSaving your song Writing to a CDCreating a new song Selecting/creating a songSelecting a song from the song list Using the name libraryRenaming a song Selecting a songMixer Effects Session Drums Recorder Switching the counter displaySwitching the information display area LocationMoving to a different location Session Drums Recorder Using the Mark keys to moveMoving to the location assigned to a mark Deleting a markFinding a zero-cross point Finding a precise location ScrubPress the Scrub key to display the Scrub Moving a song Song editing procedureSong editing Copying a songSaving a song Inputting audio to the mixerAnalog input Protecting a songUsing the tuner Sub input Inputting the digital audio signal from a MD or DATAudio outputs from the mixer Digital inputEQ Equalizer Mixer settingsAdjusting the volume Adjusting the panPairing EQ library Storing and recall- ing EQ settingsMaster EQ CH on groups Group settingsMonitor settings Fader groupsSolo settings Adjusting the cue levelMuting a channel Storing a mixer setup Mixer SetupClick the Yes button or press the panel YES key to save Renaming a scene Storing/recalling a sceneStoring a scene Recalling a sceneMidi output Specifying parameters that will be disabled for all scenesEditing and overwriting a scene Controlling scenes via MidiScene automation AutomationEvent automation Turn Automation on Rec When you play back the song, event recording will beginPlaying back the events Editing eventsNumber of effects and DSP power for each variety of effect How DSP power is allocated to the effectsEffect type and size Applying insert effects during recording Using insert effectsUsing master effects Using the final effectFor an insert effect Editing the effectsEditing the effect parameters Storing an effect programSelect the effect that you want to control Using external effectsUsing a pedal or Midi to control an effect Controlling effects from an external deviceD3200 contains 756 drum patterns →p.176 Drum Pat- tern List Listening to drum patternsCreating a drum track for an entire song Pattern Map If you’ve selected Metronome as the groupAuditioning the pattern map Recording with Session DrumsRecording additional tracks as you listen to the drum track Recording patterns on a trackEditing the sound of a drum kit Editing a drum kitSelecting a drum kit Recording directly to the master trackList, select highlight Pattern mapsCreating a pattern map Turn the Click Monitor button off normal displayEditing a pattern map TempoTap tempo Tempo trackSong Guide function Changing the tempo during the songBounce recording RecordingPattern map tempo Basic recordingTrigger recording Switching virtual tracksManual punch-in/out Using a foot switch for manual punch-in/outAuto punch-in/out Loop recording Creating a master trackSong Locate Mixer Effects Session Drums Normal playback PlaybackLoop playback Copy a track CopyTrk Track editing proceduresTrack editing Playing back an album CD projectUsing the clipboard to copy data to another song Insert blank space InsertTrk Deleting all data of a track Erase a track EraseTrkDelete a track DeleteTrk Deleting track dataReverse a track ReverseTrk Exchange tracks SwapTrkExpand/compress a track ExpCmpTrk Optimizing a track OptimizeTrkVerify the copy-destination Select the expansion/compression modeCopying to a virtual track Select the copy-source virtual trackCreating a fade-in Exchange two entire tracks SwapWholeTrkFade-in/fade-out FadeTrk Swapping entire tracksCreating a fade-out Select NoiseReduction Specify the region where you want to erase punch NoiseEliminating noise NoiseReduction Erasing punch noise ErasePunchNoiseTrack At Once Naming a trackErase a silent region EraseSilence Finalize the disc Disc At OnceAlbum CD Project Write the songCheck the CD by playing it back on an audio CD player Song Locate Mixer Effects Session Drums RecorderSpecify the size of the gaps between each track Audition the Album CD ProjectEdit the album CD project. Figure E Ripping a CDCreating a live CD Create a master track for this songBacking up Backing up and restoringBacking up 1 Song Backing up All Data Execute the backupWhen backing up to CD-R/RW When backing up to the PC driveRestoring backed-up data Importing an audio file Audio filesImporting an audio track into the beginning of a track Importing an audio file into the middle of a track Exporting an audio fileExporting an audio file Drive and data compatibility with the Digital Recording Using D32XD and D16XD dataUsing D3200 data on a different model Using data from a different model on the D3200Specifying the PC drive size Specifying the drive sizeChecking the hard disk Renaming a song driveFormatting the hard disk Drive capacity Creating a system recoveryTo keep only the audio data that you are actually using Load systemSharing event data PC driveChecking, renaming, or deleting files Deleting the Undo dataWindows users Windows Me/2000 or later Saving/loadingMacintosh users Mac OS9.0.4 or later Midi connections Using MidiMidi messages used by D3200 Synchronizing two D3200 units Using Midi to control the mixerUpgrading the system Downloading the operating systemPress the panel Enter key ClickPoint Calibration dialog box will appearCounter display CounterTime Disp Type dialog box Meter/Track View Using the name libraryRename Editing a name100 101 2a. CH INPUT/SubMixer2b-2. Fader Group 2b. PAIR/GROUP102 2b-1. Channel Pair2c-2. Automation 2c. FADER/PAN/AUTOMATION103 2c-1. Fader Pan2c-3. Event List 1042c-4. Edit Scene 1052c-5. Scene Filter 1062c-6. Mixer View 2d-2. EQ Library 2d. EQ/ATT/PHASE107 2d-1. EQ/ATT108 2d-3. Phase2d-4. Master EQ 109 2e. Send EFF/AUX/REC2f-1. Solo 2f. SOLO/MONITOR110 2e-5. Rec Send2f-3. Cue Level 2g. Mixer Setup111 2f-2. Monitor3a. Rename 112Ch View Channel Routing ViewEffect Routing 113Techniques for assigning effects 114Insert EFF Effects that can be used simultaneouslyMaster EFF1 115Effect program selection Final EFF PAN116 Master EFF2117 118 119 Disk Utility 120HDD, CD 121 Edit PC File 122Restore Backup123 Other data files Restore destination124 Album CD Project125 Edit Track 126Virtual Track Master TrackCopyTrk 127Wave dialog box 128DeleteTrk 129InsertTrk EraseTrkA3.WAVE 130SwapTrk ReverseTrkA4. Wave 131OptimizeTrk ExpCmpTrkA3. Virtual 132CopyWholeTrk SwapWholeTrkNormalizeTrk A3. Mode133 FadeTrkBefore execution After execution 134NoiseReduction ErasePunchNoiseImport File 135EraseSilence Export File 136137 11. CD138 11a. Album CD139 11b. Track at once140 11c. CD PlayerWAV 141 UndoCalib 142 Drums Track Mixer 143Pattern Map 144145 MarkTempo Track Zoom 146147 Rec ModeLOC 1/IN, … LOC 4/END Mixer Navigation Tools148 Transport keys Play/Stop Mode149 Category Dynamics&Filter Category Reverb&Delay150 Category Modulation&PitchCategory SFX&etc 151Category Multi Stereo-type About the effect algorithms152 153 C/R DelayStereo/Cross Delay 10 St. Multitap Delay Stereo Multitap DelayAuto Panning Delay 11 St.Modulation Dly Stereo Modulation Delay154 Stereo Vibrato Stereo Phaser155 Stereo Flanger19 St.Pitch Shifter Stereo Pitch Shifter 156Stereo Tremolo Stereo ExpanderStereo Filter 157Stereo Limiter Stereo GateTalking Modulator 158Multiband Limiter Category SFX&etc SFX/Etc effectsMono Reverb Room Monaural-type159 Rotary Speaker160 161 Tube Pre Amp Sim Tube PreAmp Simulator 162Mono Wah 49 Mn.Ring Modulator Mono Ring Modulator163 164 165 166 Key does not function when pressedAudio files 167Startup 168 169 170 PC USB drive Drives171 CD-R/RW driveCreating an audio CD Audio CDs and files172 Playing an audio CDFiles on the PC USB drive PC files 173Loading WAV-format audio filesGeneral 174Recorder section Midi functionalityInput 175176 Drum Pattern List177 EQ Library ListName Library List Demo Song List178 179 180 181 182 XLR jack 183Virtual track Word clock184 IndexCD-RW 185186 REC/PLAY ModeUSB 187188 189 Midi implementation chartKorg INC
Related manuals
Manual 9 pages 16.13 Kb