Korg D3200 158, Multiband Limiter, Category SFX&etc SFX/Etc effects, Talking Modulator

Page 168

26: Multiband Limiter

This is a stereo multi-band limiter. It is ideal for mastering.

Hi.Thresh (High Band Threshold)

–48.0...0.0dB

Adjusts the level at which compression begins for the high- frequency range

Hi.Attack (High Band Attack)

0...1.00sec

Adjusts the attack time for the high-frequency range

 

 

Hi.Release (High Band Release)

0...10.0sec

Adjusts the release time for the high-frequency range

Hi.OutGain (High Band Output Gain)

–24.0...+24.0dB

Adjusts the output gain for the high-frequency range

 

 

Md.Thresh (Middle Band Threshold)

–48.0...0.0dB

Adjusts the level at which compression begins for the mid- frequency range

Md.Attack (Middle Band Attack)

0...1.00sec

Adjusts the attack time for the mid-frequency range

 

 

Md.Release (Middle Band Release)

0...10.0sec

Adjusts the release time for the mid-frequency range

Md.OutGain (Middle Band Output Gain)

–24.0...+24.0dB

Adjusts the output gain for the mid-frequency range

 

 

Lo.Thresh (Low Band Threshold)

–48.0...0.0dB

Adjusts the level at which compression begins for the low- frequency range

Lo.Attack (Low Band Attack)

0...1.00sec

Adjusts the attack time for the low-frequency range

 

 

Lo.Release (Low Band Release)

0...10.0sec

Adjusts the release time for the low-frequency range

Lo.OutGain (Low Band Output Gain)

–24.0...+24.0dB

Adjusts the output gain for the low-frequency range

 

 

Mon.Band (Monitor Band)

Off, Low, Middle, High

Selects the band to monitor

 

 

Lo.Xover (Low Cross over Frequency)

53Hz...1.00kHz

Sets the frequency of the crossover between the low and mid- frequency bands

Hi.Xover (High Cross over Frequency) 1.10kHz...16.0kHz

Sets the frequency of the crossover between the mid and high- frequency bands

Saturation (Tube Saturation)

0...100%

Sets the depth of vacuum tube distortion

Category: SFX&etc

SFX/Etc effects

27:St.Analog Record (Stereo Analog Record)

RPM

33 1/3, 45, 78

 

Sets the r.p.m. of a record

Wah (Wah Flutter)

0...100%

Sets the depth by which the record is warped

 

 

Bend

0...100%

Sets the width by which the record is warped

 

 

Dry:Wet

Dry, 1:99...99:1, Wet

Sets the balance between the effect and dry sounds

ClickLevel (Click Noise Level)

0...100%

 

Sets the level of click noise

 

 

ClickAngle

0...100

Sets the angle of the scratch on the surface of the record

 

 

LoDamp (Low Damp)

THRU, 21Hz...8.00kHz

Sets the damping amount in the low range

HiDamp (High Damp)

53Hz...20.0kHz, THRU

Sets the damping amount in the high range

ClickPoint

0...100

Sets the distance of the scratch from the warped area

 

 

WhiteLevel (White Noise Level)

0...100%

 

Sets the level of white noise

 

 

NoiseLoCut (Noise Low Cut)

THRU, 21Hz...8.00kHz

Sets the low-cut frequency for the noise

NoiseHiCut (Noise High Cut)

53Hz...20.0kHz, THRU

Sets the high-cut frequency for the noise

 

 

Vinyl Level (Vinyl Noise Level)

0...100%

Sets the level of noise produced by the needle scraping the vinyl

Vinyl Type (Vinyl Noise Type)

0...3

 

Selects the type of vinyl noise

ClickAngle:

 

This sets the angle of the scratch. The spacing of the click noise for one revolution will depend on the angle.

Vinyl Noise Type:

The Vinyl Noise will also depend on the amount by which the record is warped.

28: Talking Modulator

This effect gives the input signal a character similar to a hu- man voice. It can create the impression of a talking guitar or synthesizer

V.Bottom (Voice Bottom)

[A], [E], [I], [O], [U]

Selects a vowel sound at the bottom end of control

V.Centr (Voice Center)

[A], [E], [I], [O], [U]

Selects a vowel sound in the center of control

 

 

V.Top (Voice Top)

[A], [E], [I], [O], [U]

Selects a vowel sound at the top end of control

 

 

Drive (Drive Gain)

0.0...+36dB

Sets the amount of gain for the distortion

Control (Control Source)

Envelope, LFO, Manual

 

Switches the control source

 

 

*LFO Speed

0.02...20.00Hz

 

Sets the LFO speed

 

 

Env.Resp (Envelope Response)

Slow, Medium, Fast

Selects the response speed of envelope control

Env.Sens (Envelope Sensitivity)

0...100%

Sets the sensitivity of envelope control

 

 

L Delay (L Delay Time)

0...2.730sec

 

Sets the left delay time

 

 

R Delay (R Delay Time)

0...2.730sec

 

Sets the right delay time

 

 

*Manual (Manual Control)

0...100

Sets the control position manually

 

 

Dry:Wet

Dry, 1:99...99:1, Wet

Sets the balance between the effect and dry sounds

Wet Trim (Wet Level Trim)

0...100

 

Sets the effect level trim

29:St.Ring Modulator (Stereo Ring Modulator)

This effect creates a metallic sound by applying the oscilla- tors to the input signal.

Oscillator (Oscillator Frequency)

0...12.00kHz

 

Sets the oscillator frequency

 

 

*LFO Speed

0.02...20.00Hz

Sets the LFO speed of the oscillator frequency modulation

 

 

*LFO Depth

0...100%

Sets the depth of LFO modulation for the oscillator frequency

158

Image 168
Contents Page Important Safety Instructions Handling of the internal hard disk Data handlingIii RW drive Printing conventions in this ManualTable of Contents Mixer EffectsSession Drums Vii RecorderData Reference ViiiAppendices Specifications 174 More about drives and files 171Various lists 176 Before using the D3200 for the first time Power on/offPower-on Included itemsSetting the calendar Power-offPress the SYSTEM/MIDI key Click the Control tab Main features Parts and their function Functions LCD screen Connection exampleInput Main features Track digital multi-track recorderSession Drums Mixer scene memories, plus Midi control of mixer parametersCD-R/RW drive for creating backup disk and audio CDs What is ?Sophisticated digital editing tools Intuitive interface designed for ease-of-usePhantom power switch Parts and their functionTop panel Input 1, Input 2...INPUT 12 jacks60 -40 dBu mic input 13 1-16 key, 17-32 key 14 REC/PLAY keyCH on key Solo keyDirect keys Knob MatrixScrub key Mark keyLOOP, TRIGGER, Auto Punch indicators 37 REC/PLAY Mode keys40 HDD/CD access and Midi indicators On key, standby indicatorRear panel About the CD-R/RW drive Items and functions in the LCD screen ViewList button Scroll bar/scroll buttonsConfirmation button Radio buttonsSelecting the page mode Selecting and setting parametersBasic operation Switching between channels 1-16 Send and equalizerEditing effects Selecting a channelExamples of operation Connections Turn the D3200 onPlease note the following items before you begin ConnectionsAdjust the mix When the demo song ends, press the Stop keyListen to the demo song Press the Song key to access the Song Create a new songName the song Create the songConnect your audio sources to the mixer inputs Connect mics and instruments to the Input jacksConfirm the changes Connect a guitar to the guitar inputAssign the inputs to channels Press the EQ key to access the EQ/ATT tab Choose a channel Use the Knob Matrix to adjust the EQAdjust the EQ settings of channel Adding EQ and EffectsReverb&Delay in the Mono Applying effects to the input soundChoose an effect type Choose an effect programSetting the recording mode RecordingPreparations for recording Normal Select the recording statusPlayback Start recordingOverdubbing Arm track 2 for recordingPress the EQ key to access the EQ/ATT tab Applying effects and EQ to individual channelsApplying EQ to each channel/track Adjusting the pan Selecting a master effectSelect a track for EQ Select an effect programAdjusting the Master Effect 1 Send amount for each track Checking and adjusting the master effectAdjust the send amount of each track Adjust the return form the master effectsMake the desired adjustments, and then press the Stop key Set the meters to display the post fader levelsApplying an effect to the master bus Final Effect Choose a final effectWhen you‘re done adjusting the master EQ, press the Stop key Applying EQ to the master bus Master EQAdjust the recording level Recording the master trackSpecify a virtual track Arm the master track for recordingWriting to a CD Saving your songSelecting/creating a song Creating a new songUsing the name library Renaming a songSelecting a song Selecting a song from the song listSwitching the counter display Switching the information display areaLocation Mixer Effects Session Drums RecorderMoving to a different location Using the Mark keys to move Moving to the location assigned to a markDeleting a mark Session Drums RecorderFinding a precise location Scrub Finding a zero-cross pointPress the Scrub key to display the Scrub Song editing procedure Song editingCopying a song Moving a songInputting audio to the mixer Analog inputProtecting a song Saving a songUsing the tuner Inputting the digital audio signal from a MD or DAT Audio outputs from the mixerDigital input Sub inputMixer settings Adjusting the volumeAdjusting the pan EQ EqualizerEQ library Storing and recall- ing EQ settings PairingMaster EQ Group settings Monitor settingsFader groups CH on groupsAdjusting the cue level Solo settingsMuting a channel Mixer Setup Storing a mixer setupClick the Yes button or press the panel YES key to save Storing/recalling a scene Storing a sceneRecalling a scene Renaming a sceneSpecifying parameters that will be disabled for all scenes Editing and overwriting a sceneControlling scenes via Midi Midi outputAutomation Scene automationEvent automation When you play back the song, event recording will begin Playing back the eventsEditing events Turn Automation on RecHow DSP power is allocated to the effects Number of effects and DSP power for each variety of effectEffect type and size Using insert effects Using master effectsUsing the final effect Applying insert effects during recordingEditing the effects Editing the effect parametersStoring an effect program For an insert effectUsing external effects Using a pedal or Midi to control an effectControlling effects from an external device Select the effect that you want to controlListening to drum patterns Creating a drum track for an entire song Pattern MapIf you’ve selected Metronome as the group D3200 contains 756 drum patterns →p.176 Drum Pat- tern ListRecording with Session Drums Recording additional tracks as you listen to the drum trackRecording patterns on a track Auditioning the pattern mapEditing a drum kit Selecting a drum kitRecording directly to the master track Editing the sound of a drum kitPattern maps Creating a pattern mapTurn the Click Monitor button off normal display List, select highlightTempo Editing a pattern mapTempo track Song Guide functionChanging the tempo during the song Tap tempoRecording Pattern map tempoBasic recording Bounce recordingSwitching virtual tracks Trigger recordingUsing a foot switch for manual punch-in/out Manual punch-in/outAuto punch-in/out Creating a master track Loop recordingSong Locate Mixer Effects Session Drums Playback Normal playbackLoop playback Track editing procedures Track editingPlaying back an album CD project Copy a track CopyTrkUsing the clipboard to copy data to another song Insert blank space InsertTrk Erase a track EraseTrk Delete a track DeleteTrkDeleting track data Deleting all data of a trackExchange tracks SwapTrk Reverse a track ReverseTrkOptimizing a track OptimizeTrk Expand/compress a track ExpCmpTrkSelect the expansion/compression mode Copying to a virtual trackSelect the copy-source virtual track Verify the copy-destinationExchange two entire tracks SwapWholeTrk Fade-in/fade-out FadeTrkSwapping entire tracks Creating a fade-inCreating a fade-out Specify the region where you want to erase punch Noise Eliminating noise NoiseReductionErasing punch noise ErasePunchNoise Select NoiseReductionNaming a track Track At OnceErase a silent region EraseSilence Disc At Once Album CD ProjectWrite the song Finalize the discSong Locate Mixer Effects Session Drums Recorder Specify the size of the gaps between each trackAudition the Album CD Project Check the CD by playing it back on an audio CD playerRipping a CD Creating a live CDCreate a master track for this song Edit the album CD project. Figure EBacking up and restoring Backing upBacking up 1 Song Execute the backup When backing up to CD-R/RWWhen backing up to the PC drive Backing up All DataRestoring backed-up data Audio files Importing an audio fileImporting an audio track into the beginning of a track Exporting an audio file Importing an audio file into the middle of a trackExporting an audio file Using D32XD and D16XD data Using D3200 data on a different modelUsing data from a different model on the D3200 Drive and data compatibility with the Digital RecordingSpecifying the drive size Specifying the PC drive sizeRenaming a song drive Checking the hard diskFormatting the hard disk Creating a system recovery To keep only the audio data that you are actually usingLoad system Drive capacityPC drive Checking, renaming, or deleting filesDeleting the Undo data Sharing event dataSaving/loading Windows users Windows Me/2000 or laterMacintosh users Mac OS9.0.4 or later Using Midi Midi connectionsMidi messages used by D3200 Using Midi to control the mixer Synchronizing two D3200 unitsDownloading the operating system Upgrading the systemClickPoint Calibration dialog box will appear Press the panel Enter keyCounter Counter displayTime Disp Type dialog box Using the name library RenameEditing a name Meter/Track View100 2a. CH INPUT/SubMixer 1012b. PAIR/GROUP 1022b-1. Channel Pair 2b-2. Fader Group2c. FADER/PAN/AUTOMATION 1032c-1. Fader Pan 2c-2. Automation104 2c-3. Event List105 2c-4. Edit Scene106 2c-5. Scene Filter2c-6. Mixer View 2d. EQ/ATT/PHASE 1072d-1. EQ/ATT 2d-2. EQ Library2d-3. Phase 1082d-4. Master EQ 2e. Send EFF/AUX/REC 1092f. SOLO/MONITOR 1102e-5. Rec Send 2f-1. Solo2g. Mixer Setup 1112f-2. Monitor 2f-3. Cue Level112 Ch ViewChannel Routing View 3a. Rename113 Effect Routing114 Insert EFFEffects that can be used simultaneously Techniques for assigning effects115 Master EFF1Effect program selection PAN 116Master EFF2 Final EFF117 118 119 120 Disk UtilityHDD, CD 121 122 Edit PC FileBackup Restore123 Restore destination 124Album CD Project Other data files125 126 Virtual TrackMaster Track Edit Track127 CopyTrk128 Wave dialog box129 InsertTrkEraseTrk DeleteTrk130 SwapTrkReverseTrk A3.WAVE131 OptimizeTrkExpCmpTrk A4. Wave132 CopyWholeTrkSwapWholeTrk A3. VirtualA3. Mode 133FadeTrk NormalizeTrk134 NoiseReductionErasePunchNoise Before execution After execution135 Import FileEraseSilence 136 Export File11. CD 13711a. Album CD 13811b. Track at once 13911c. CD Player 140WAV Undo 141Calib 142 143 Drums Track Mixer144 Pattern MapMark 145Tempo Track 146 ZoomRec Mode LOC 1/IN, … LOC 4/ENDMixer Navigation Tools 147148 Play/Stop Mode Transport keys149 Category Reverb&Delay 150Category Modulation&Pitch Category Dynamics&Filter151 Category SFX&etcCategory Multi About the effect algorithms Stereo-type152 C/R Delay Stereo/Cross Delay10 St. Multitap Delay Stereo Multitap Delay 15311 St.Modulation Dly Stereo Modulation Delay Auto Panning Delay154 Stereo Phaser 155Stereo Flanger Stereo Vibrato156 Stereo TremoloStereo Expander 19 St.Pitch Shifter Stereo Pitch Shifter157 Stereo LimiterStereo Gate Stereo Filter158 Multiband LimiterCategory SFX&etc SFX/Etc effects Talking ModulatorMonaural-type 159Rotary Speaker Mono Reverb Room160 161 162 Mono Wah49 Mn.Ring Modulator Mono Ring Modulator Tube Pre Amp Sim Tube PreAmp Simulator163 164 165 Key does not function when pressed 166167 Audio filesStartup 168 169 170 Drives 171CD-R/RW drive PC USB driveAudio CDs and files 172Playing an audio CD Creating an audio CD173 LoadingWAV-format audio files Files on the PC USB drive PC files174 Recorder sectionMidi functionality General175 InputDrum Pattern List 176EQ Library List Name Library ListDemo Song List 177178 179 180 181 182 183 Virtual trackWord clock XLR jackIndex 184185 CD-RWREC/PLAY Mode 186187 USB188 Midi implementation chart 189Korg INC
Related manuals
Manual 9 pages 16.13 Kb