Omega RD260A instruction manual Operation mode, SET mode, SET UP mode, Turning the function off

Page 46

5.1 Various Modes

The recorder has three modes which are described below:

OPERATION mode

This is the mode for daily operation; when the power turns on, the recorder automatically enters this mode. For details, see chapter 4 “DAILY OPERATION AND MAINTENANCE”.

SET mode

In this mode, daily-used data such as alarm setpoints, date, and time are set. Pressing the [DISP] key three seconds in the OPERATION mode changes the mode to the SET mode.

SET UP mode

In this mode, you make settings for digital printing, alarm, burnout function and others, also adjust the pen’s position or the position where the recorder prints dots. You can enter this mode by turning the power on while pressing the [CH UP] (ENT) key.

NOTE While in the SET UP mode, measurement, recording, and alarm detection are not carried out.

Using the SETTINGS PROTECTION FUNCTION, you can protect your settings by defining a password when you enter the SET or SET UP mode. For details on the settings protection function, see section 7.17.

Turning the function off:

	Power ON while pressing
Power ON	the [CH UP] (↵ ENT) key.

OPERATION mode

SET mode

SETUP mode

Mode changes to the other by pressing the [DISP] key for three seconds.

Leaving the SET UP mode is done by SET UP END procedure.

Turning the function on:

Power ON while pressing

the [CH UP] (↵ ENT) key.

Power ON

QUIT

SETUP

Password

OPERATION

SET mode

SETUP mode

mode

*1

*1

Password

Leaving the SET UP mode

DISP

3 sec.

is done by SET UP END

*1 Mode changes to the other by pressing

procedure.

the [DISP] key for three seconds.

5 - 2

Image 46

Contents User’s Guide Servicing North America Introduction Power Supply Alternative currentDefects of Protective Grounding and Fuse Protective GroundingNecessity of Protective Grounding FuseInstallation ChaptersContents Setting A/D Integration Time Pen model Before Installation Handling PrecautionsChecking and Unpacking Checking Accessories and AppearanceAccessories No. Name Qty Remarks Spare Parts NameRemoving Packings Removing Lock Screw and Packings for TransitChecking Model Codes Checking Model CodesInstallation Site and Mounting Methods Installation SiteMounting Methods MountingExternal Dimensions Panel cutoutPen model WiringRear Panel Terminal Arrangement Dot-printing modelPower Supply Wiring Power Supply WiringInput Signal Wiring Crimp-On LugsRTD input Wiring for Input TerminalsTC input Terminal BoardOutput type Alarm Output Wiring optionContact characteristics Output capacityRemote Control Wiring option Input characteristicsComponent Names and Functions Front Panel Power switch push-button typeKey panel push-key type Status Display Chart cassetteData Display Characters on the Display Maintenance Switching Power On/OffInstalling or Replacing Chart Paper Prepare a new chart Replacement under pen-replacement mode Installing or Replacing Pens Pen modelSimple replacement Felt-tip penPlotter pen Installing or Replacing Ribbon Cassette Dot-printing model Starting/Stoping the Recording Feeding the ChartGetting the Recording Printing SamplesGetting a Digital Printout Getting a List PrintoutGetting a SET UP List Printout Dot-printing model Printing SampleDisplay MAN except for the 1-pen model Selectting the DisplaySelecting a screen Periodic Maintenance MaintenanceIndication of Remaining Chart Length Cleaning the Carriage Shafts Battery ReplacementFuse Replacement Fuse ReplacementPen model CalibrationDot-printing model Required instruments for calibration Calibration procedureDC Voltage Signal for Pen model same as Dot-printing model Recommended instrumentsTemperature Compensation for Thermocouple Signal Reference Junction Compensation for Thermocouple InputPen-Position Adjustment Pen model Adjusting procedureDaily OPERATION/MAINTENANCE Dot-Position Adjustment Dot-printing model Figure aDaily OPERATION/MAINTENANCE Data Setting Guides SET UP mode Operation modeSET mode Turning the function offOperation Mode Disp keySET Mode SET UP Mode Password Procedures to Enter Setting Data SET Mode Setting Input Range and Recording Span Range Key operation Skip SettingIndication Description Voltage Measurement Setting Volt Setting Volt Input Ranges DisplayKey operation Indication Description TC Type Description and RTD Type DescriptionDigital Input Setting DI Setting Difference Computation Setting Delt Setting Scale Setting SCL Setting Indication DiscriptionKey operation Indication Discription Setting to Obtain Square Root Sqrt SettingENT key Explanation of Square Root Setting Offsets Offst Setting Alarms Alarm Is displayed and the setting is completed. Press Assigning Units Unit Setting Chart Speed Chart Chart Speed unit mm/hSetting Date/Time Clock FIX Auto Assigning Tags TAG Setting Messages MSG Means ‘SPACE’Setting Key-lock KEY SET UP Mode Setting Procedure Setting Alarm Hysteresis On/Off Setting A/D Integration Time Pen model Setting Upscale/Downscale TC Burnout Select Using the key. Press the ENT key Display AppearsConfiguring the Input Filter Pen Model Filter works as followsBuffer data for Setting for Moving Average Calculations Dot-printing modelNth sample +1th sample Turning Offset Settings Protection On/Off Assigning Different Colors to Channels Dot-printing model To select Display, and press the ENT key SelectSetting Pen Offset Compensation On/Off Pen model, /D1 option Recorder as Viewed from the SideTurning Alarm Printing On/Off Use Key to select the display Press the ENT keyPen Model Chart Speed Setting Periodic Printout On/OffDot-printing Model Chart Speed Turning Printing of Changes in Chart Speed On/Off Setting ProcedureSetting Procedure Selecting channel Number or Tag Changing the Temperature Unit /D2 option Select Using the key Press the ENT key. The display AppearsChanging Default Settings for Remote Operation option Turning the Settings Protection Function On/Off Initializing Settings Error Codes Error Code ListRecovery Self-diagnostic Message Printout Meanings Store SET UP Settings AgaiinTroubleshooting Recorder is completely inoperativeIs the input free of noise? Glitch is found other than the previously mentioned ploblems Warrant Y/ Disclaimer OMEGA…Of Course