Omega RD260A instruction manual Troubleshooting, Recorder is completely inoperative

Page 93

8.2 Troubleshooting

8.2 Troubleshooting

Recorder is completely inoperative

Is the power switch ON?

Does the switch turn properly?

YES

Is the power supply properly connected?

YES

Does the power meet the specified rating?

YES

Is the fuse blown?

YES

Replace the fuse.

YES

Is the fuse blown just after replaced?

YES

Contact OMEGA Engineering.

NO	See section 4.1.
Turn the switch on properly

NO	See subsection 2.2.2.
Connect the supply lines properly.

NO	Supply the power with specified
	voltage/frequency.

NO	Contact OMEGA Engineering.

See subsection 4.8.3.

NO

End

8. TROUBLESHOOTING

8 - 3

Image 93

Contents User’s Guide Servicing North America Introduction Alternative current Power SupplyNecessity of Protective Grounding Protective GroundingDefects of Protective Grounding and Fuse FuseChapters InstallationContents Setting A/D Integration Time Pen model Handling Precautions Before InstallationAccessories No. Name Qty Remarks Checking Accessories and AppearanceChecking and Unpacking Spare Parts NameRemoving Lock Screw and Packings for Transit Removing PackingsChecking Model Codes Checking Model CodesInstallation Site Installation Site and Mounting MethodsMounting Mounting MethodsPanel cutout External DimensionsRear Panel Terminal Arrangement WiringPen model Dot-printing modelPower Supply Wiring Power Supply WiringCrimp-On Lugs Input Signal WiringTC input Wiring for Input TerminalsRTD input Terminal BoardContact characteristics Alarm Output Wiring optionOutput type Output capacityInput characteristics Remote Control Wiring optionComponent Names and Functions Power switch push-button type Front PanelKey panel push-key type Chart cassette Status DisplayData Display Characters on the Display Switching Power On/Off MaintenanceInstalling or Replacing Chart Paper Prepare a new chart Simple replacement Installing or Replacing Pens Pen modelReplacement under pen-replacement mode Felt-tip penPlotter pen Installing or Replacing Ribbon Cassette Dot-printing model Getting the Recording Feeding the ChartStarting/Stoping the Recording Printing SamplesGetting a List Printout Getting a Digital PrintoutDot-printing model Printing Sample Getting a SET UP List PrintoutSelectting the Display Display MAN except for the 1-pen modelSelecting a screen Maintenance Periodic MaintenanceIndication of Remaining Chart Length Fuse Replacement Battery ReplacementCleaning the Carriage Shafts Fuse ReplacementCalibration Pen modelDot-printing model DC Voltage Signal for Pen model same as Dot-printing model Calibration procedureRequired instruments for calibration Recommended instrumentsReference Junction Compensation for Thermocouple Input Temperature Compensation for Thermocouple SignalAdjusting procedure Pen-Position Adjustment Pen modelDaily OPERATION/MAINTENANCE Figure a Dot-Position Adjustment Dot-printing modelDaily OPERATION/MAINTENANCE Data Setting Guides SET mode Operation modeSET UP mode Turning the function offDisp key Operation ModeSET Mode SET UP Mode Password Procedures to Enter Setting Data SET Mode Setting Input Range and Recording Span Range Skip Setting Key operationIndication Description Volt Input Ranges Display Voltage Measurement Setting Volt SettingTC Type Description and RTD Type Description Key operation Indication DescriptionDigital Input Setting DI Setting Difference Computation Setting Delt Setting Indication Discription Scale Setting SCL SettingSetting to Obtain Square Root Sqrt Setting Key operation Indication DiscriptionENT key Explanation of Square Root Setting Offsets Offst Setting Alarms Alarm Is displayed and the setting is completed. Press Assigning Units Unit Chart Speed unit mm/h Setting Chart Speed ChartSetting Date/Time Clock FIX Auto Assigning Tags TAG Means ‘SPACE’ Setting Messages MSGSetting Key-lock KEY SET UP Mode Setting Procedure Setting Alarm Hysteresis On/Off Setting A/D Integration Time Pen model Select Using the key. Press the ENT key Display Appears Setting Upscale/Downscale TC BurnoutFilter works as follows Configuring the Input Filter Pen ModelSetting for Moving Average Calculations Dot-printing model Buffer data forNth sample +1th sample Turning Offset Settings Protection On/Off To select Display, and press the ENT key Select Assigning Different Colors to Channels Dot-printing modelRecorder as Viewed from the Side Setting Pen Offset Compensation On/Off Pen model, /D1 optionUse Key to select the display Press the ENT key Turning Alarm Printing On/OffSetting Periodic Printout On/Off Pen Model Chart SpeedDot-printing Model Chart Speed Setting Procedure Turning Printing of Changes in Chart Speed On/OffSetting Procedure Selecting channel Number or Tag Select Using the key Press the ENT key. The display Appears Changing the Temperature Unit /D2 optionChanging Default Settings for Remote Operation option Turning the Settings Protection Function On/Off Initializing Settings Error Code List Error CodesRecovery Store SET UP Settings Agaiin Self-diagnostic Message Printout MeaningsRecorder is completely inoperative TroubleshootingIs the input free of noise? Glitch is found other than the previously mentioned ploblems Warrant Y/ Disclaimer OMEGA…Of Course