Omega RD260A instruction manual Is displayed and the setting is completed. Press

Page 64

PRINT FEED

CH UP

PRINT

CH UP

PRINT

CH UP

NOTE

	ESC
CH UP	DISP	3 sec
		3 sec

NOTE

6.3 Setting Alarms (ALARM)

The display which appears will allow you to enter the alarm value.

Set the alarm value using the [ ] and [ ] keys. After setting, press the [ENT] key.

The decimal point is predetermined by the input range.

Relationship between Input Range and Decimal Points

	Type of Input		Position of Decimal Point

		–20.00 to 20.00 mV	XXX. XX
		–60.00 to 60.00 mV	XXX. XX
DC Voltage		–200.0 to 200.0 mV	XXXX. X
		–2.000 to 2.000 V	XX. XXX
		–6.000 to 6.000 V	XX. XXX
		–20.00 to 20.00 V	XXX. XX

Thermocouple/RTD (˚C)			XXXX. X

The following settings are available only for the model with relay options (A2/A4/A6). For models without these options, the alarm setting ends by pressing the [ENT] key until

[ ] appears.

Determines whether the relay outputs a signal or not when an alarm occurs.

Select ON/OFF by the [ ] key, and press the [ENT] key.

Sets the number of the relay after the alarm output ON is selected. A numeric to be set is selected from I01 to I06 by the [ ] key. Then press the [ENT] key.

If a number larger than the available number of output relays is selected, the alarm output will not implemented.

[	] is displayed and the setting is completed. Press

the [ENT] key to set another channel; or press the [DISP] key for three seconds to return to the OPERATION mode.

•As a merged function, a combination of remote control option (- R) and alarm output relay option is available to change the chart speed when an alarm occurs.

•If you press the [ESC] key in the middle of setting, the indication returns to

the [ ] and already set data will be aborted.

6. SET MODE

6 - 13

Image 64

Contents User’s Guide Servicing North America Introduction Power Supply Alternative currentProtective Grounding Necessity of Protective GroundingDefects of Protective Grounding and Fuse FuseInstallation ChaptersContents Setting A/D Integration Time Pen model Before Installation Handling PrecautionsChecking Accessories and Appearance Accessories No. Name Qty RemarksChecking and Unpacking Spare Parts NameRemoving Packings Removing Lock Screw and Packings for TransitChecking Model Codes Checking Model CodesInstallation Site and Mounting Methods Installation SiteMounting Methods MountingExternal Dimensions Panel cutoutWiring Rear Panel Terminal ArrangementPen model Dot-printing modelPower Supply Wiring Power Supply WiringInput Signal Wiring Crimp-On LugsWiring for Input Terminals TC inputRTD input Terminal BoardAlarm Output Wiring option Contact characteristicsOutput type Output capacityRemote Control Wiring option Input characteristicsComponent Names and Functions Front Panel Power switch push-button typeKey panel push-key type Status Display Chart cassetteData Display Characters on the Display Maintenance Switching Power On/OffInstalling or Replacing Chart Paper Prepare a new chart Installing or Replacing Pens Pen model Simple replacementReplacement under pen-replacement mode Felt-tip penPlotter pen Installing or Replacing Ribbon Cassette Dot-printing model Feeding the Chart Getting the RecordingStarting/Stoping the Recording Printing SamplesGetting a Digital Printout Getting a List PrintoutGetting a SET UP List Printout Dot-printing model Printing SampleDisplay MAN except for the 1-pen model Selectting the DisplaySelecting a screen Periodic Maintenance MaintenanceIndication of Remaining Chart Length Battery Replacement Fuse ReplacementCleaning the Carriage Shafts Fuse ReplacementPen model CalibrationDot-printing model Calibration procedure DC Voltage Signal for Pen model same as Dot-printing modelRequired instruments for calibration Recommended instrumentsTemperature Compensation for Thermocouple Signal Reference Junction Compensation for Thermocouple InputPen-Position Adjustment Pen model Adjusting procedureDaily OPERATION/MAINTENANCE Dot-Position Adjustment Dot-printing model Figure aDaily OPERATION/MAINTENANCE Data Setting Guides Operation mode SET modeSET UP mode Turning the function offOperation Mode Disp keySET Mode SET UP Mode Password Procedures to Enter Setting Data SET Mode Setting Input Range and Recording Span Range Key operation Skip SettingIndication Description Voltage Measurement Setting Volt Setting Volt Input Ranges DisplayKey operation Indication Description TC Type Description and RTD Type DescriptionDigital Input Setting DI Setting Difference Computation Setting Delt Setting Scale Setting SCL Setting Indication DiscriptionKey operation Indication Discription Setting to Obtain Square Root Sqrt SettingENT key Explanation of Square Root Setting Offsets Offst Setting Alarms Alarm Is displayed and the setting is completed. Press Assigning Units Unit Setting Chart Speed Chart Chart Speed unit mm/hSetting Date/Time Clock FIX Auto Assigning Tags TAG Setting Messages MSG Means ‘SPACE’Setting Key-lock KEY SET UP Mode Setting Procedure Setting Alarm Hysteresis On/Off Setting A/D Integration Time Pen model Setting Upscale/Downscale TC Burnout Select Using the key. Press the ENT key Display AppearsConfiguring the Input Filter Pen Model Filter works as followsBuffer data for Setting for Moving Average Calculations Dot-printing modelNth sample +1th sample Turning Offset Settings Protection On/Off Assigning Different Colors to Channels Dot-printing model To select Display, and press the ENT key SelectSetting Pen Offset Compensation On/Off Pen model, /D1 option Recorder as Viewed from the SideTurning Alarm Printing On/Off Use Key to select the display Press the ENT keyPen Model Chart Speed Setting Periodic Printout On/OffDot-printing Model Chart Speed Turning Printing of Changes in Chart Speed On/Off Setting ProcedureSetting Procedure Selecting channel Number or Tag Changing the Temperature Unit /D2 option Select Using the key Press the ENT key. The display AppearsChanging Default Settings for Remote Operation option Turning the Settings Protection Function On/Off Initializing Settings Error Codes Error Code ListRecovery Self-diagnostic Message Printout Meanings Store SET UP Settings AgaiinTroubleshooting Recorder is completely inoperativeIs the input free of noise? Glitch is found other than the previously mentioned ploblems Warrant Y/ Disclaimer OMEGA…Of Course