Aussie Bonza Deluxe, Kanga Fixed LEG/SIDE Table Assembly Tools, Item 9 8 pcs, Item 10 8 pcs

Page 10

STEP 2- FIXED LEG/SIDE TABLE ASSEMBLY TOOLS:

 

 

 

 

 

 

 

 

 

 

 

 

OR

 

 

 

 

 

 

 

 

(ITEM 1, 3, OR 4) SIDE TABLE

 

 

(ITEM 9) 8 pcs

 

 

 

(ITEM 10) 8 pcs

 

 

 

 

 

1/4” x 1 3/8” BOLT

 

 

1/4” x 1” BOLT

 

 

 

 

 

 

 

(ITEM 12) FRONT FIXED LEG - WOOD

(ITEM 14) FRONT FIXED LEG - METAL

OR

 

 

(ITEM 13) REAR FIXED LEG - METAL

(ITEM 11) REAR FIXED LEG - WOOD

 

 

 

•In the same way, attach the Front and Rear Fixed Legs to the remaining Side Table using 1/4” x 1” Bolts (1/4” x 1 3/8” for Metal Legs.)

•On models with wooden legs, be sure to position Fixed Legs with the four large recessed holes facing away from Side Table (Fig. C) and the two threaded holes in edge of each leg pointing outward. (Fig. D) Do not tighten bolts completely. (Metal Tubing Legs can be oriented either way.)

FRONT FIXED LEG

KANGA, BONZA - WOOD

BONZA DELUXE - METAL

SIDE TABLE

(Tear Drop Table

Shown)

REAR FIXED LEG

KANGA, BONZA - WOOD

BONZA DELUXE - METAL

FIG. C

FOUR LARGE RECESSED HOLES (Wooden Legs Only)

1/4” x 1” BOLT

(1/4” x 1 3/8” Deluxe Models)

FRONT FIXED LEG THREE VELCRO PATCHES FACE INSIDE

FIG. D

THREADED HOLES IN LEGS (Deluxed Models with Metal legs do not have these threaded holes.)

10

Image 10
Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone Bonza PART/DESCRIPTIONKanga Bonza PART/ Description QTY Kanga BonzaPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Wheel LEG/ Side Table Assembly Tools Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcsItem 10 8 pcs Fixed LEG/SIDE Table Assembly ToolsItem 9 8 pcs Tear Drop Table ShownLegbrace Assembly Tools X 1 Bolt 8 pcs PcsX 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt Metal Bottom SHELF/LEG & Caster Assembly ToolsItem 19, 20 X 2 Bolt Wood 1/4 X 1 3/8 Bolt MetalItem 27 4 pcs WHEEL/ Cylinder Bracket Assembly ToolsItem 23, 24 X 1/2 BoltItem 30 Spacer 8 pcs Grill BODY/CART ASSEMBLY- Kanga Models ToolsAssembly Next Item 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUTAssemble Grill Body to CART- Kanga Models 6mm X 110mmItem 32 6mm Wing NUT 8pcs Grill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models ToolsItem 31 Actual Size 6mm x 110mm Bolt Pcs Continue Assembly of Bonza & Bonza Deluxe Models AT Step Grill BODY/CART ASSEMBLY- Bonza Models6mm x 110mm Bolts Next Install Burner ToolsAttach Decorative Privacy Panel to Cart ALL Models Or 4 PCSCotter PIN Install from underneath Backside of grill Adjust Tab if greater than 3/1616 GAP Install Ceramic Briquette Trays & Grids ALL Models Install Bottom Body PANEL/GREASE TRAY- ALL Models#8 X 1/2 Screw 2pcs SCREW, #10 X 3/8 Attach Handle to Weather Cover LID Kanga Models Tools#10 X 3/8 Screw Attach Handle and Heat Indicator to Hood Bonza Models Tools Attach LP Cylinder to Grill ALL Models FIG. KLeak Testing to be Performed in a WELL-VENTILATED Area How to perform a leak testGAS, CYLINDER, Hose Regulator Information Connecting/ Disconnecting LP Gas Cylinder to GrillLP Gas Cylinder Precautions Before Using Your LP GAS GrillSelecting a Location LeakTesting Operating the LP GAS GrillTurn LP cylinder handle counter-clockwise on Lighting the Grill Using the Integra Spark Ignition SystemPreparation Before Cooking Confirm each burner is lit before lighting another burnerManual Lighting of the Grill Turn off Your LP Gas Grill Care and MaintenanceCheck Your Flame End of Cooking Session Grill CookingBurner Maintenance How to clean procelain coated cast iron burnersCeramic Briquettes Cleaning the Grill BodyPreventive Maintenance Bottom Panel/ Grease TrayBurners will not light Using the ignitorUsing a match Low flame or low heatFlare up Flames blow outPersistent grease fire Important Notice Aussie Grill Company Limited Warranty