Aussie Bonza Deluxe, Kanga owner manual Bottom SHELF/LEG & Caster Assembly Tools, Item 19, 20

Page 12

STEP 4-BOTTOM SHELF/LEG & CASTER ASSEMBLY

TOOLS:

 

(ITEM 9) 4 pcs 1/4” x 1” BOLT

(ITEM 22) 1/4” X 2” BOLT 4 pcs

 

 

(ITEM 17 OR 18) AXLE

(ITEM 10) 8 pcs

 

 

 

1/4” X 1 3/8” BOLT

 

 

(DELUXE MODELS)

 

 

 

 

 

(ITEM 16) BOTTOM SHELF

(ITEM 19, 20, 21)

CASTER ASSEMBLY

•Place Leg/Side Table assemblies opposite each other as shown with the velcro patches on same side. •Place Bottom Shelf inside of Wheel Leg assembly and align large axle holes. Insert Axle through axle holes in both sides of legs and shelf. The Axle will support this end of Bottom Shelf while

securing Fixed Leg assembly.

•For Kanga and Bonza Models, position Caster Assembly with caster wheels up and side of bracket against Bottom Shelf. Align the Caster Bracket, Bottom Shelf, and Fixed Leg holes and

fasten using 1/4” X 2” Bolts. Attach Wheel Legs to Bottom Shelf using 1/4” x 1” Bolts. Metal Tubing Legs will use 1/4” x 1 3/8” Bolts. Tighten Wheel Leg bolts before proceeding.

•For Bonza Deluxe, align the Bottom Shelf and Leg holes and fasten using 1/4” x 1 3/8” bolts. Attach Bonza Deluxe Wheel Legs the same way. Thread casters into end of leg.

Bonza Deluxe - Important Note: When assembling Bottom Shelf on metal legs, the Axle hole in the Bottom Shelf is not used(See Illustration below).

DELUXE

METAL LEG

WHEEL LEG

ASSEMBLY

1/4” x 1” BOLT - WOOD LEG 1/4” x 1 3/8” BOLT - METAL

BOTTOM SHELF

AXLE

VELCRO

PATCHES

ON THIS

SIDE

1/4” x 2” BOLT - WOOD 1/4” X 1 3/8” BOLT - METAL

 

 

 

 

 

 

CASTER

 

 

DELUXE

ASSEMBLY

 

 

 

 

 

 

 

CASTER

 

 

 

 

 

 

 

 

 

METAL

 

 

 

 

 

LEG

 

 

 

 

 

 

 

 

 

 

 

 

FIXED LEG

ASSEMBLY

1/4” x 1” BOLT - WOOD LEG 1/4” x 1 3/8” BOLT - METAL LEG

12

Image 12
Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone PART/DESCRIPTION BonzaKanga Bonza PART/ Description QTY Kanga BonzaPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Wheel LEG/ Side Table Assembly Tools Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcsFixed LEG/SIDE Table Assembly Tools Item 9 8 pcsItem 10 8 pcs Tear Drop Table ShownLegbrace Assembly Tools X 1 Bolt 8 pcs PcsBottom SHELF/LEG & Caster Assembly Tools Item 19, 20X 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt Metal X 2 Bolt Wood 1/4 X 1 3/8 Bolt MetalWHEEL/ Cylinder Bracket Assembly Tools Item 23, 24Item 27 4 pcs X 1/2 BoltGrill BODY/CART ASSEMBLY- Kanga Models Tools Assembly NextItem 30 Spacer 8 pcs Item 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUTAssemble Grill Body to CART- Kanga Models 6mm X 110mmGrill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models Tools Item 32 6mm Wing NUT 8pcsItem 31 Actual Size 6mm x 110mm Bolt Pcs Grill BODY/CART ASSEMBLY- Bonza Models Continue Assembly of Bonza & Bonza Deluxe Models AT Step6mm x 110mm Bolts Install Burner Tools Attach Decorative Privacy Panel to Cart ALL ModelsNext Or 4 PCSAdjust Tab if greater than 3/16 Cotter PIN Install from underneath Backside of grill16 GAP Install Bottom Body PANEL/GREASE TRAY- ALL Models Install Ceramic Briquette Trays & Grids ALL Models#8 X 1/2 Screw 2pcs Attach Handle to Weather Cover LID Kanga Models Tools SCREW, #10 X 3/8#10 X 3/8 Screw Attach Handle and Heat Indicator to Hood Bonza Models Tools Attach LP Cylinder to Grill ALL Models FIG. KLeak Testing to be Performed in a WELL-VENTILATED Area How to perform a leak testConnecting/ Disconnecting LP Gas Cylinder to Grill GAS, CYLINDER, Hose Regulator InformationLP Gas Cylinder Before Using Your LP GAS Grill PrecautionsSelecting a Location LeakTesting Operating the LP GAS GrillLighting the Grill Using the Integra Spark Ignition System Preparation Before CookingTurn LP cylinder handle counter-clockwise on Confirm each burner is lit before lighting another burnerManual Lighting of the Grill Care and Maintenance Check Your Flame End of Cooking SessionTurn off Your LP Gas Grill Grill CookingBurner Maintenance How to clean procelain coated cast iron burnersCleaning the Grill Body Preventive MaintenanceCeramic Briquettes Bottom Panel/ Grease TrayUsing the ignitor Using a matchBurners will not light Low flame or low heatFlames blow out Flare upPersistent grease fire Important Notice Aussie Grill Company Limited Warranty