Aussie Kanga, Bonza Deluxe owner manual Important Notice

Page 35

IMPORTANT NOTICE

The gas grill is setup to operate with a LP Gas Cylinder equipped

with an OPD (Overfilling Prevention Device).

This is a secondary device to prevent the overfilling of your LP Gas cylinder. The proper methods for the filling of your LP Gas cylinder are by weight or volume, as described in NFPA 58. Please make sure your filling station fills your LP Gas cylinder by weight or volume. Ask your filling station to read purging and filling instructions on the LP cylinder before attempting to fill.

Rises up while filling then stops when full.

WARNING! Do not exchange the LP Gas cylinder unless the exchange LP cylinder is equipped with an OPD. Otherwise you will lose the OPD (Overfilling Prevention Device) feature. If there is not an LP cylinder available for exchange equipped with an OPD, we recommend that you have your cylinder filled at an authorized LP gas dealer by a qualified attendant.

Image 35

Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone Kanga Bonza PART/DESCRIPTIONBonza QTY Kanga Bonza PART/ DescriptionPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcs Wheel LEG/ Side Table Assembly ToolsTear Drop Table Shown Fixed LEG/SIDE Table Assembly ToolsItem 9 8 pcs Item 10 8 pcsX 1 Bolt 8 pcs Pcs Legbrace Assembly ToolsX 2 Bolt Wood 1/4 X 1 3/8 Bolt Metal Bottom SHELF/LEG & Caster Assembly ToolsItem 19, 20 X 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt MetalX 1/2 Bolt WHEEL/ Cylinder Bracket Assembly ToolsItem 23, 24 Item 27 4 pcsItem 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUT Grill BODY/CART ASSEMBLY- Kanga Models ToolsAssembly Next Item 30 Spacer 8 pcs6mm X 110mm Assemble Grill Body to CART- Kanga ModelsItem 31 Actual Size 6mm x 110mm Bolt Pcs Grill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models ToolsItem 32 6mm Wing NUT 8pcs 6mm x 110mm Bolts Grill BODY/CART ASSEMBLY- Bonza ModelsContinue Assembly of Bonza & Bonza Deluxe Models AT Step Or 4 PCS Install Burner ToolsAttach Decorative Privacy Panel to Cart ALL Models Next16 GAP Adjust Tab if greater than 3/16Cotter PIN Install from underneath Backside of grill #8 X 1/2 Screw 2pcs Install Bottom Body PANEL/GREASE TRAY- ALL ModelsInstall Ceramic Briquette Trays & Grids ALL Models #10 X 3/8 Screw Attach Handle to Weather Cover LID Kanga Models ToolsSCREW, #10 X 3/8 Attach Handle and Heat Indicator to Hood Bonza Models Tools FIG. K Attach LP Cylinder to Grill ALL ModelsHow to perform a leak test Leak Testing to be Performed in a WELL-VENTILATED AreaLP Gas Cylinder Connecting/ Disconnecting LP Gas Cylinder to GrillGAS, CYLINDER, Hose Regulator Information Selecting a Location Before Using Your LP GAS GrillPrecautions Operating the LP GAS Grill LeakTestingConfirm each burner is lit before lighting another burner Lighting the Grill Using the Integra Spark Ignition SystemPreparation Before Cooking Turn LP cylinder handle counter-clockwise onManual Lighting of the Grill Grill Cooking Care and MaintenanceCheck Your Flame End of Cooking Session Turn off Your LP Gas GrillHow to clean procelain coated cast iron burners Burner MaintenanceBottom Panel/ Grease Tray Cleaning the Grill BodyPreventive Maintenance Ceramic BriquettesLow flame or low heat Using the ignitorUsing a match Burners will not lightPersistent grease fire Flames blow outFlare up Important Notice Aussie Grill Company Limited Warranty