Aussie Bonza Deluxe, Kanga owner manual Adjust Tab if greater than 3/16, 16 GAP

Page 19

•Fit venturi end of Burner through hole in the inside firewall (behind control panel) and onto Gas Control Valve Nozzle (Fig. G & Fig. H). Be careful not to bend or force gas collector plates.

Holes in

Front firewall.

			Manual Lighting
	Gas Nozzle		Manual Lighting
	Gas Nozzle		Holes
	Control Vavle		Holes
	Control Vavle

Gas Collector and

Electrode

Venturi end of Burner inserted over gas nozzle.

Top plate

of gas collector.

FIG. G		FIG. H

REFERENCE: ELECTRODE GAP

Adjust Tab if greater than 3/16”.

ELECTRODE	3/16” GAP
	3/16” GAP
	MAX.

TAB-GAS COLLECTOR

BURNER

•Place other end of burner on lower shoulder of rear firewall so Burner Peg rests in Burner Locator Hole as shown (Fig. I).

•Using Pliers, insert Cotter Pin through hole in Burner Peg to secure. This is easier done from backside of grill looking up underneath rear firewall.

•Repeat above steps for remaining burners .

FIG. I

BURNER PEG

BURNER LOCATOR HOLE IN LOWER SHOULDER

COTTER PIN Install from underneath Backside of grill.

Image 19

Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone Bonza PART/DESCRIPTIONKanga Bonza QTY Kanga Bonza PART/ DescriptionPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcs Wheel LEG/ Side Table Assembly ToolsTear Drop Table Shown Fixed LEG/SIDE Table Assembly ToolsItem 9 8 pcs Item 10 8 pcsX 1 Bolt 8 pcs Pcs Legbrace Assembly ToolsX 2 Bolt Wood 1/4 X 1 3/8 Bolt Metal Bottom SHELF/LEG & Caster Assembly ToolsItem 19, 20 X 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt MetalX 1/2 Bolt WHEEL/ Cylinder Bracket Assembly ToolsItem 23, 24 Item 27 4 pcsItem 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUT Grill BODY/CART ASSEMBLY- Kanga Models ToolsAssembly Next Item 30 Spacer 8 pcs6mm X 110mm Assemble Grill Body to CART- Kanga ModelsItem 32 6mm Wing NUT 8pcs Grill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models ToolsItem 31 Actual Size 6mm x 110mm Bolt Pcs Continue Assembly of Bonza & Bonza Deluxe Models AT Step Grill BODY/CART ASSEMBLY- Bonza Models6mm x 110mm Bolts Or 4 PCS Install Burner ToolsAttach Decorative Privacy Panel to Cart ALL Models NextCotter PIN Install from underneath Backside of grill Adjust Tab if greater than 3/1616 GAP Install Ceramic Briquette Trays & Grids ALL Models Install Bottom Body PANEL/GREASE TRAY- ALL Models#8 X 1/2 Screw 2pcs SCREW, #10 X 3/8 Attach Handle to Weather Cover LID Kanga Models Tools#10 X 3/8 Screw Attach Handle and Heat Indicator to Hood Bonza Models Tools FIG. K Attach LP Cylinder to Grill ALL ModelsHow to perform a leak test Leak Testing to be Performed in a WELL-VENTILATED AreaGAS, CYLINDER, Hose Regulator Information Connecting/ Disconnecting LP Gas Cylinder to GrillLP Gas Cylinder Precautions Before Using Your LP GAS GrillSelecting a Location Operating the LP GAS Grill LeakTestingConfirm each burner is lit before lighting another burner Lighting the Grill Using the Integra Spark Ignition SystemPreparation Before Cooking Turn LP cylinder handle counter-clockwise onManual Lighting of the Grill Grill Cooking Care and MaintenanceCheck Your Flame End of Cooking Session Turn off Your LP Gas GrillHow to clean procelain coated cast iron burners Burner MaintenanceBottom Panel/ Grease Tray Cleaning the Grill BodyPreventive Maintenance Ceramic BriquettesLow flame or low heat Using the ignitorUsing a match Burners will not lightFlare up Flames blow outPersistent grease fire Important Notice Aussie Grill Company Limited Warranty

FIG. G

FIG. H

Adjust Tab if greater than 3/16”.

3/16” GAP

COTTER PIN Install from underneath Backside of grill.