Aussie Bonza Deluxe, Kanga WHEEL/ Cylinder Bracket Assembly Tools, Item 23, 24, Item 27 4 pcs

Page 13

STEP 5-WHEEL/ CYLINDER BRACKET ASSEMBLY		TOOLS:
		TOOLS:
(ITEM 23, 24, & 25)
WHEEL ASSEMBLY	(ITEM 27) 4 pcs		(ITEM 26) CYLINDER BRACKET
2 PCS	(ITEM 27) 4 pcs
	1/4” x 1/2” BOLT

•Slide Axle out. With the notched side of Cylinder Bracket down, secure the Cylinder Bracket to wheel end of Bottom Shelf using ¼” x ½” Bolts and tighten.

•Slide Axle back into position and push a Wheel Assembly onto each end of axle until the spring clip locks into place.

•On Deluxe Models, slide end caps onto each Fixed Leg.

•GO TO STEP 7 FOR BONZA AND BONZA DELUXE MODELS.

1/4” x 1/2” BOLTS

CYLINDER BRACKET

WHEEL ASSEMBLY

Image 13

Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone Bonza PART/DESCRIPTIONKanga Bonza QTY Kanga Bonza PART/ DescriptionPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcs Wheel LEG/ Side Table Assembly ToolsItem 9 8 pcs Fixed LEG/SIDE Table Assembly ToolsItem 10 8 pcs Tear Drop Table ShownX 1 Bolt 8 pcs Pcs Legbrace Assembly ToolsItem 19, 20 Bottom SHELF/LEG & Caster Assembly ToolsX 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt Metal X 2 Bolt Wood 1/4 X 1 3/8 Bolt MetalItem 23, 24 WHEEL/ Cylinder Bracket Assembly ToolsItem 27 4 pcs X 1/2 BoltAssembly Next Grill BODY/CART ASSEMBLY- Kanga Models ToolsItem 30 Spacer 8 pcs Item 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUT6mm X 110mm Assemble Grill Body to CART- Kanga ModelsItem 32 6mm Wing NUT 8pcs Grill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models ToolsItem 31 Actual Size 6mm x 110mm Bolt Pcs Continue Assembly of Bonza & Bonza Deluxe Models AT Step Grill BODY/CART ASSEMBLY- Bonza Models6mm x 110mm Bolts Attach Decorative Privacy Panel to Cart ALL Models Install Burner ToolsNext Or 4 PCSCotter PIN Install from underneath Backside of grill Adjust Tab if greater than 3/1616 GAP Install Ceramic Briquette Trays & Grids ALL Models Install Bottom Body PANEL/GREASE TRAY- ALL Models#8 X 1/2 Screw 2pcs SCREW, #10 X 3/8 Attach Handle to Weather Cover LID Kanga Models Tools#10 X 3/8 Screw Attach Handle and Heat Indicator to Hood Bonza Models Tools FIG. K Attach LP Cylinder to Grill ALL ModelsHow to perform a leak test Leak Testing to be Performed in a WELL-VENTILATED AreaGAS, CYLINDER, Hose Regulator Information Connecting/ Disconnecting LP Gas Cylinder to GrillLP Gas Cylinder Precautions Before Using Your LP GAS GrillSelecting a Location Operating the LP GAS Grill LeakTestingPreparation Before Cooking Lighting the Grill Using the Integra Spark Ignition SystemTurn LP cylinder handle counter-clockwise on Confirm each burner is lit before lighting another burnerManual Lighting of the Grill Check Your Flame End of Cooking Session Care and MaintenanceTurn off Your LP Gas Grill Grill CookingHow to clean procelain coated cast iron burners Burner MaintenancePreventive Maintenance Cleaning the Grill BodyCeramic Briquettes Bottom Panel/ Grease TrayUsing a match Using the ignitorBurners will not light Low flame or low heatFlare up Flames blow outPersistent grease fire Important Notice Aussie Grill Company Limited Warranty

STEP 5-WHEEL/ CYLINDER BRACKET ASSEMBLY

TOOLS:

(ITEM 23, 24, & 25)

(ITEM 27) 4 pcs

1/4” x 1/2” BOLT

1/4” x 1/2” BOLTS