Aussie Bonza Deluxe, Kanga owner manual Attach Handle and Heat Indicator to Hood Bonza Models Tools

Page 22

STEP 13-ATTACH HANDLE AND HEAT INDICATOR TO HOOD - BONZA MODELS

TOOLS:

(ITEM 44 ACTUAL SIZE) 6mm x 90mm BOLT

2 pcs

(ITEM 46) HANDLE SPACER

(ITEM 45) HOOD HANDLE

(ITEM 47) 6mm LOCKNUT

2 pcs

2 pcs

 

(ITEM 49) LOCKWASHER

(ITEM 50) 10-24 HEX NUT

(ITEM 48) HEAT INDICATOR

2 pcs

2 pcs

 

 

 

•Insert two 6mm x 90mm Bolts through recessed holes of Hood Handle, through Handle Spacers, into front of hood and secure with 6mm Locknuts. Be sure to place the wide end of Spacer against the Hood. Do not overtighten or you may crack Hood finish.

•Insert Heat Indicator studs into Hood holes and secure using two Lockwashers and two 10-24 Hexnuts. Do not overtighten or you may crack Hood finish.

LOCKNUT

 

LOCKWASHER

 

10-24 HEX NUT

 

 

 

 

 

 

 

 

 

 

SPACERS

HEAT

INDICATOR

6mm x 90mm

 

BOLT

HOOD HANDLE

 

22

Image 22
Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone Bonza PART/DESCRIPTIONKanga Bonza PART/ Description QTY Kanga BonzaPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Wheel LEG/ Side Table Assembly Tools Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcsItem 10 8 pcs Fixed LEG/SIDE Table Assembly ToolsItem 9 8 pcs Tear Drop Table ShownLegbrace Assembly Tools X 1 Bolt 8 pcs PcsX 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt Metal Bottom SHELF/LEG & Caster Assembly ToolsItem 19, 20 X 2 Bolt Wood 1/4 X 1 3/8 Bolt MetalItem 27 4 pcs WHEEL/ Cylinder Bracket Assembly ToolsItem 23, 24 X 1/2 BoltItem 30 Spacer 8 pcs Grill BODY/CART ASSEMBLY- Kanga Models ToolsAssembly Next Item 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUTAssemble Grill Body to CART- Kanga Models 6mm X 110mmItem 32 6mm Wing NUT 8pcs Grill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models ToolsItem 31 Actual Size 6mm x 110mm Bolt Pcs Continue Assembly of Bonza & Bonza Deluxe Models AT Step Grill BODY/CART ASSEMBLY- Bonza Models6mm x 110mm Bolts Next Install Burner ToolsAttach Decorative Privacy Panel to Cart ALL Models Or 4 PCSCotter PIN Install from underneath Backside of grill Adjust Tab if greater than 3/1616 GAP Install Ceramic Briquette Trays & Grids ALL Models Install Bottom Body PANEL/GREASE TRAY- ALL Models#8 X 1/2 Screw 2pcs SCREW, #10 X 3/8 Attach Handle to Weather Cover LID Kanga Models Tools#10 X 3/8 Screw Attach Handle and Heat Indicator to Hood Bonza Models Tools Attach LP Cylinder to Grill ALL Models FIG. KLeak Testing to be Performed in a WELL-VENTILATED Area How to perform a leak testGAS, CYLINDER, Hose Regulator Information Connecting/ Disconnecting LP Gas Cylinder to GrillLP Gas Cylinder Precautions Before Using Your LP GAS GrillSelecting a Location LeakTesting Operating the LP GAS GrillTurn LP cylinder handle counter-clockwise on Lighting the Grill Using the Integra Spark Ignition SystemPreparation Before Cooking Confirm each burner is lit before lighting another burnerManual Lighting of the Grill Turn off Your LP Gas Grill Care and MaintenanceCheck Your Flame End of Cooking Session Grill CookingBurner Maintenance How to clean procelain coated cast iron burnersCeramic Briquettes Cleaning the Grill BodyPreventive Maintenance Bottom Panel/ Grease TrayBurners will not light Using the ignitorUsing a match Low flame or low heatFlare up Flames blow outPersistent grease fire Important Notice Aussie Grill Company Limited Warranty