Aussie Kanga, Bonza Deluxe owner manual Manual Lighting of the Grill

Page 29

Manual Lighting of the Grill

4)Locate the control knob that corresponds to the match lighting hole that you are using. Push in and turn the control knob counter-clockwise until a click is heard.

·Open Lid or Hood (depending on the model) before lighting the grill to prevent an explosion from gas build-up.

·The Lid (Kanga™ series only) must never be covering the cooking surface while the LP gas grill is in use or hot.

·Always inspect the gas hose and regulator assembly

before each use. If the hose is cut, damaged, or showing signs of excessive abrasion or wear, do not use the LP gas grill.

Contact the manufacturer, as the hose must be replaced with an assembly specified by the manufacturer prior to further use of the LP gas grill.

How to manually light your LP gas grill

1)Open Lid or Hood (depending on the model)

2)Important: The LP gas cylinder valve must be opened first before turning the control knobs on the grill. Turn the handle on the LP cylinder valve counter- clockwise until it stops.

3)Insert a lit match through one of the match-lighting holes underneath the front control panel on the grill. (See figure below).

WARNING: If the burner fails to ignite after following the above procedure, turn all the knobs to the off position and close the valve on the LP cylinder. Wait five minutes and repeat all of the above manual lighting procedures. If the grill still fails to light, see the Troubleshooting page.

5)Light the remaining burners from left to right by turning the control knob counter-clockwise. Your grill has a crossover ignition system that allows the burners to light successively off one another. Confirm each burner is lit before

lighting another burner.

6)After ignition, burners should be burned at the high position for 3-5 minutes in order to preheat the grill. This process should be done before every cooking session. The hood (Bonza™ series only) should be closed during preheating. The lid (Kanga™ series only) must never be covering the cooking surface while the grill is in use or hot.

WARNING: If a burner goes out during the cooking cycle, turn all knobs to the off position and close the valve on the LP cylinder. Open hood (BonzaTM series only) and wait five minutes before attempting to relight the grill.

1. Open lid or hood (depending on model)

2. Turn LP cylinder han- dle counter-clockwise -

3.Match lighting hole in left side of grill body - Insert a lit match through the match lighting hole.

4.Push in and turn control

knob counter-clockwise to the “High” position. (Note a click may be heard)

29

Image 29
Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone Kanga Bonza PART/DESCRIPTIONBonza QTY Kanga Bonza PART/ DescriptionPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcs Wheel LEG/ Side Table Assembly ToolsItem 9 8 pcs Fixed LEG/SIDE Table Assembly ToolsItem 10 8 pcs Tear Drop Table ShownX 1 Bolt 8 pcs Pcs Legbrace Assembly ToolsItem 19, 20 Bottom SHELF/LEG & Caster Assembly ToolsX 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt Metal X 2 Bolt Wood 1/4 X 1 3/8 Bolt MetalItem 23, 24 WHEEL/ Cylinder Bracket Assembly ToolsItem 27 4 pcs X 1/2 BoltAssembly Next Grill BODY/CART ASSEMBLY- Kanga Models ToolsItem 30 Spacer 8 pcs Item 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUT6mm X 110mm Assemble Grill Body to CART- Kanga ModelsItem 31 Actual Size 6mm x 110mm Bolt Pcs Grill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models ToolsItem 32 6mm Wing NUT 8pcs 6mm x 110mm Bolts Grill BODY/CART ASSEMBLY- Bonza ModelsContinue Assembly of Bonza & Bonza Deluxe Models AT Step Attach Decorative Privacy Panel to Cart ALL Models Install Burner ToolsNext Or 4 PCS16 GAP Adjust Tab if greater than 3/16Cotter PIN Install from underneath Backside of grill #8 X 1/2 Screw 2pcs Install Bottom Body PANEL/GREASE TRAY- ALL ModelsInstall Ceramic Briquette Trays & Grids ALL Models #10 X 3/8 Screw Attach Handle to Weather Cover LID Kanga Models ToolsSCREW, #10 X 3/8 Attach Handle and Heat Indicator to Hood Bonza Models Tools FIG. K Attach LP Cylinder to Grill ALL ModelsHow to perform a leak test Leak Testing to be Performed in a WELL-VENTILATED AreaLP Gas Cylinder Connecting/ Disconnecting LP Gas Cylinder to GrillGAS, CYLINDER, Hose Regulator Information Selecting a Location Before Using Your LP GAS GrillPrecautions Operating the LP GAS Grill LeakTestingPreparation Before Cooking Lighting the Grill Using the Integra Spark Ignition SystemTurn LP cylinder handle counter-clockwise on Confirm each burner is lit before lighting another burnerManual Lighting of the Grill Check Your Flame End of Cooking Session Care and MaintenanceTurn off Your LP Gas Grill Grill CookingHow to clean procelain coated cast iron burners Burner MaintenancePreventive Maintenance Cleaning the Grill BodyCeramic Briquettes Bottom Panel/ Grease TrayUsing a match Using the ignitorBurners will not light Low flame or low heatPersistent grease fire Flames blow outFlare up Important Notice Aussie Grill Company Limited Warranty