Aussie Bonza Deluxe owner manual Assemble Grill Body to CART- Kanga Models, 6mm X 110mm

Page 15

STEP 6-(CONTINUED) ASSEMBLE GRILL BODY TO CART- KANGA MODELS

•Turn Grill Body upside down and position between cart legs with the Hose and Regulator on the Wheel Leg end. Do not lay Grill Body on, or step on, the Hose and Regulator.

6mm X 110mm

BOLT

•Align slotted holes on sides of Grill Body with

CASTER LOCK

6mm X 110mm

BOLT

BODY

WINGNUT

holes through edges of legs (Fig. E). Hold Spacers between Leg and Body (Needle Nose Pliers may help) and insert Body Bolts through Leg, Spacers, and slotted holes in Grill Body. Secure using Wing Nuts but only partially tighten. Repeat assembly for remaining three Cart Legs.

•Using a second person, turn full grill assembly upright with wheels and casters on the ground. The Grill Body should slide down to seat itself in slotted holes. If not, loosen the Body Bolts and push Body down at all corners.Tighten all Body Bolts and Wing Nuts and then tighten all other Bolts.

•Adjust the Lock Lever up or down on each Caster to lock or unlock as desired. (NOTE: Deluxe Models do not use casters.)

SPACER

FIG. E

BOLT

SPACER

WINGNUTS

Continue assembly of Kanga at STEP 8.

15

Image 15
Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone PART/DESCRIPTION BonzaKanga Bonza QTY Kanga Bonza PART/ DescriptionPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcs Wheel LEG/ Side Table Assembly ToolsTear Drop Table Shown Fixed LEG/SIDE Table Assembly ToolsItem 9 8 pcs Item 10 8 pcsX 1 Bolt 8 pcs Pcs Legbrace Assembly ToolsX 2 Bolt Wood 1/4 X 1 3/8 Bolt Metal Bottom SHELF/LEG & Caster Assembly ToolsItem 19, 20 X 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt MetalX 1/2 Bolt WHEEL/ Cylinder Bracket Assembly ToolsItem 23, 24 Item 27 4 pcsItem 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUT Grill BODY/CART ASSEMBLY- Kanga Models ToolsAssembly Next Item 30 Spacer 8 pcs6mm X 110mm Assemble Grill Body to CART- Kanga ModelsGrill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models Tools Item 32 6mm Wing NUT 8pcsItem 31 Actual Size 6mm x 110mm Bolt Pcs Grill BODY/CART ASSEMBLY- Bonza Models Continue Assembly of Bonza & Bonza Deluxe Models AT Step6mm x 110mm Bolts Or 4 PCS Install Burner ToolsAttach Decorative Privacy Panel to Cart ALL Models NextAdjust Tab if greater than 3/16 Cotter PIN Install from underneath Backside of grill16 GAP Install Bottom Body PANEL/GREASE TRAY- ALL Models Install Ceramic Briquette Trays & Grids ALL Models#8 X 1/2 Screw 2pcs Attach Handle to Weather Cover LID Kanga Models Tools SCREW, #10 X 3/8#10 X 3/8 Screw Attach Handle and Heat Indicator to Hood Bonza Models Tools FIG. K Attach LP Cylinder to Grill ALL ModelsHow to perform a leak test Leak Testing to be Performed in a WELL-VENTILATED AreaConnecting/ Disconnecting LP Gas Cylinder to Grill GAS, CYLINDER, Hose Regulator InformationLP Gas Cylinder Before Using Your LP GAS Grill PrecautionsSelecting a Location Operating the LP GAS Grill LeakTestingConfirm each burner is lit before lighting another burner Lighting the Grill Using the Integra Spark Ignition SystemPreparation Before Cooking Turn LP cylinder handle counter-clockwise onManual Lighting of the Grill Grill Cooking Care and MaintenanceCheck Your Flame End of Cooking Session Turn off Your LP Gas GrillHow to clean procelain coated cast iron burners Burner MaintenanceBottom Panel/ Grease Tray Cleaning the Grill BodyPreventive Maintenance Ceramic BriquettesLow flame or low heat Using the ignitorUsing a match Burners will not lightFlames blow out Flare upPersistent grease fire Important Notice Aussie Grill Company Limited Warranty