Aussie Kanga, Bonza owner manual Before Using Your LP GAS Grill, Selecting a Location, Precautions

Page 26

·Never connect or disconnect LP gas cylinder or fittings while grill is in use or is hot.

·When the LP gas cylinder is connected, the grill must be kept outside in a well-ventilated space. Turn off all of the grill control knobs and the LP cylinder valve when grill is not in use.

·Move gas hose as far away as possible from hot surfaces.

How to Connect your LP gas cylinder (See STEP 14 of Assembly Instructions for diagram)

1)Make sure all of the control panel knobs are turned to the “off” position and verify that the LP gas cylinder valve is closed by turning the handle on the LP gas cylinder valve clockwise until it stops.

2)Remove the protective cap from the LP cylinder gas nozzle.

3)Hold regulator in a straight line with LP cylinder gas nozzle so the connection does not cross thread.

4)Insert nipple into the LP cylinder nozzle opening.

5)Hand tighten coupling nut in a clockwise direction. Do not use tools.

6)Perform a Leak Test. (See STEP 15 of Assembly Instructions for Leak Test Instructions)

How to Disconnect your LP gas cylinder

1)Turn all control knobs to the “off” position and turn the handle on the LP gas cylinder clockwise until it stops.

2)Turn coupling nut on regulator in a counter-clockwise direction until regulator is released from threaded LP cylinder gas nozzle.

3)Place the protective cap over LP cylinder gas nozzle.

BEFORE USING YOUR

LP GAS GRILL

Selecting a Location

·Do not use an LP gas grill indoors, on recreational vehicles, or on a boat.

·This LP gas grill is for outdoor use only and should be placed on firm, level surface. The grill should be setup in an open area with good ventilation, away from high traffic areas and combustible materials.

·Combustible or flammable materials should never be used or stored within 36 inches of the back or sides of your LP gas grill.

·Locate your LP gas grill at least 10 feet away from your house or any building. Do not use the grill in a garage, breezeway, carport, porch, or under a surface that can catch fire.

·When moving or lifting your Aussie LP gas grill, its recommended that you grasp the cross supports under the side tables. Do not lift the grill with only the individual side table slats.

·When moving your gas grill, you should push the grill in front of you with the large wheels in the front.

Precautions

·Carefully read the Important Safeguards section of this manual (pages 2 thru 4). Make sure you follow and understand all instructions and warnings. Ifyou have any questions regarding these pages, call 1-800-251-7558 and ask for a Customer Service Representative.

·This installation must conform with local codes or, in the abscence of local codes, with either the National Fuel Gas Code, ANSI Z223.1, or CAN/CGA-B149.2, Propane Installation Code.

·If an external electrical source is utilized, the outdoor cooking appliance, when installed, must be electrically grounded in accordance with local codes or, in the absence of local codes, with the National Electrical Codes, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.1.

·If any electric appliance or rotisserie is used with the LP gas grill, do not allow cords to touch or be near hot surfaces. Electric cords should be placed away from walkways to avoid a tripping hazard.

·Grill storage cover must be removed and placed at least 36 inches from the LP gas grill while in use. The grill cover is made of a flammable material. The grill must be completely cooled before putting the cover back on the grill.

·Never store a spare or disconnected LP gas cylinder under or near this LP gas grill.

·Inspect the hose and regulator assembly before each use. If the hose is cut or damaged or shows signs of excessive abrasion or wear, do not use the LP gas grill. Contact the manufacturer, as the hose must be replaced with an assembly specified by the manufacturer prior to the further use of the LP gas grill.

·Use only the hose and regulator assembly that is supplied with your LP gas grill.

·Use of this LP gas grill other than for the intended use, or alteration of the LP gas grill in any way may not be safe and will void any warranty.

·LP gas is not natural gas. The conversion or attempted use of natural gas in an LP unit is dangerous and will void your warranty.

·Never use an LP gas cylinder if it shows signs of: dents, gouges, bulges, fire damage, corrosion, leak age, excessive rust, or other forms of visual external damage; it may be hazardous and should be checked by a Liquefied Petroleum supplier. Do not use an LP cylinder with a damaged valve.

·Never use charcoal in your LP gas grill. Do not use aerosols or store flammable liquids or materials near this gas grill.

26

Image 26
Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone Kanga Bonza PART/DESCRIPTIONBonza PART/ Description QTY Kanga BonzaPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Wheel LEG/ Side Table Assembly Tools Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcsItem 10 8 pcs Fixed LEG/SIDE Table Assembly ToolsItem 9 8 pcs Tear Drop Table ShownLegbrace Assembly Tools X 1 Bolt 8 pcs PcsX 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt Metal Bottom SHELF/LEG & Caster Assembly ToolsItem 19, 20 X 2 Bolt Wood 1/4 X 1 3/8 Bolt MetalItem 27 4 pcs WHEEL/ Cylinder Bracket Assembly ToolsItem 23, 24 X 1/2 BoltItem 30 Spacer 8 pcs Grill BODY/CART ASSEMBLY- Kanga Models ToolsAssembly Next Item 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUTAssemble Grill Body to CART- Kanga Models 6mm X 110mmItem 31 Actual Size 6mm x 110mm Bolt Pcs Grill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models ToolsItem 32 6mm Wing NUT 8pcs 6mm x 110mm Bolts Grill BODY/CART ASSEMBLY- Bonza ModelsContinue Assembly of Bonza & Bonza Deluxe Models AT Step Next Install Burner ToolsAttach Decorative Privacy Panel to Cart ALL Models Or 4 PCS16 GAP Adjust Tab if greater than 3/16Cotter PIN Install from underneath Backside of grill #8 X 1/2 Screw 2pcs Install Bottom Body PANEL/GREASE TRAY- ALL ModelsInstall Ceramic Briquette Trays & Grids ALL Models #10 X 3/8 Screw Attach Handle to Weather Cover LID Kanga Models ToolsSCREW, #10 X 3/8 Attach Handle and Heat Indicator to Hood Bonza Models Tools Attach LP Cylinder to Grill ALL Models FIG. KLeak Testing to be Performed in a WELL-VENTILATED Area How to perform a leak testLP Gas Cylinder Connecting/ Disconnecting LP Gas Cylinder to GrillGAS, CYLINDER, Hose Regulator Information Selecting a Location Before Using Your LP GAS GrillPrecautions LeakTesting Operating the LP GAS GrillTurn LP cylinder handle counter-clockwise on Lighting the Grill Using the Integra Spark Ignition SystemPreparation Before Cooking Confirm each burner is lit before lighting another burnerManual Lighting of the Grill Turn off Your LP Gas Grill Care and MaintenanceCheck Your Flame End of Cooking Session Grill CookingBurner Maintenance How to clean procelain coated cast iron burnersCeramic Briquettes Cleaning the Grill BodyPreventive Maintenance Bottom Panel/ Grease TrayBurners will not light Using the ignitorUsing a match Low flame or low heatPersistent grease fire Flames blow outFlare up Important Notice Aussie Grill Company Limited Warranty