Aussie Kanga, Bonza Deluxe owner manual Grill BODY/CART ASSEMBLY- Bonza Models, 6mm x 110mm Bolts

Page 17

STEP 7-(CONTINUED) GRILL BODY/CART ASSEMBLY- BONZA MODELS

•Lay Grill Body on its back side with control panel up. Place Grill Body between legs and Side Tables with Hose and Regulator on Wheel Leg end. Do not lay Grill Body on, or step on Hose and

Regulator.

•Align slotted holes on sides of Grill Body with holes through edges of legs (Fig F). Hold Spacers between Leg and Body (Needle Nose Pliers may help) and insert Body Bolts through Leg, Spacers, and slotted holes in Grill Body. Secure using Wing Nuts, but only partially tighten. Repeat assembly for remaining three Cart Legs.

•Using a second person, turn full grill assembly upright with wheels and legs/casters on the ground. Grill Body should slide down and seat itself within the slotted holes. If not, loosen the Body Bolts and push Body down at the corners. Tighten all Body Bolts and Wing Nuts and then tighten all other Bolts.

•Adjust the Lock Lever up or down on each Caster to lock or unlock as desired. (NOTE: Deluxe models do not use casters.)

CONTINUE ASSEMBLY OF BONZA & BONZA DELUXE MODELS AT STEP 8.

CONTROL PANEL UP

GRILL BODY LYING

ON BACK SIDE

FIG. F

WINGNUTS

SPACERSBOLTS

SPACERS

WINGNUTS

WINGNUTS

6mm x 110mm BOLTS

SPACERS

CART ASSEMBLY

17

Image 17

Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone Kanga Bonza PART/DESCRIPTIONBonza QTY Kanga Bonza PART/ DescriptionPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcs Wheel LEG/ Side Table Assembly ToolsItem 9 8 pcs Fixed LEG/SIDE Table Assembly ToolsItem 10 8 pcs Tear Drop Table ShownX 1 Bolt 8 pcs Pcs Legbrace Assembly ToolsItem 19, 20 Bottom SHELF/LEG & Caster Assembly ToolsX 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt Metal X 2 Bolt Wood 1/4 X 1 3/8 Bolt MetalItem 23, 24 WHEEL/ Cylinder Bracket Assembly ToolsItem 27 4 pcs X 1/2 BoltAssembly Next Grill BODY/CART ASSEMBLY- Kanga Models ToolsItem 30 Spacer 8 pcs Item 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUT6mm X 110mm Assemble Grill Body to CART- Kanga ModelsItem 31 Actual Size 6mm x 110mm Bolt Pcs Grill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models ToolsItem 32 6mm Wing NUT 8pcs 6mm x 110mm Bolts Grill BODY/CART ASSEMBLY- Bonza ModelsContinue Assembly of Bonza & Bonza Deluxe Models AT Step Attach Decorative Privacy Panel to Cart ALL Models Install Burner ToolsNext Or 4 PCS16 GAP Adjust Tab if greater than 3/16Cotter PIN Install from underneath Backside of grill #8 X 1/2 Screw 2pcs Install Bottom Body PANEL/GREASE TRAY- ALL ModelsInstall Ceramic Briquette Trays & Grids ALL Models #10 X 3/8 Screw Attach Handle to Weather Cover LID Kanga Models ToolsSCREW, #10 X 3/8 Attach Handle and Heat Indicator to Hood Bonza Models Tools FIG. K Attach LP Cylinder to Grill ALL ModelsHow to perform a leak test Leak Testing to be Performed in a WELL-VENTILATED AreaLP Gas Cylinder Connecting/ Disconnecting LP Gas Cylinder to GrillGAS, CYLINDER, Hose Regulator Information Selecting a Location Before Using Your LP GAS GrillPrecautions Operating the LP GAS Grill LeakTestingPreparation Before Cooking Lighting the Grill Using the Integra Spark Ignition SystemTurn LP cylinder handle counter-clockwise on Confirm each burner is lit before lighting another burnerManual Lighting of the Grill Check Your Flame End of Cooking Session Care and MaintenanceTurn off Your LP Gas Grill Grill CookingHow to clean procelain coated cast iron burners Burner MaintenancePreventive Maintenance Cleaning the Grill BodyCeramic Briquettes Bottom Panel/ Grease TrayUsing a match Using the ignitorBurners will not light Low flame or low heatPersistent grease fire Flames blow outFlare up Important Notice Aussie Grill Company Limited Warranty