Aussie Bonza Burners will not light, Using the ignitor, Using a match, Low flame or low heat

Page 33

TROUBLESHOOTING

Problem

Possible Cause

Solution

 

 

 

Burners will not light

Burners not assembled cor-

See Step 9 - Install Burners of the Assembly Instructions

using the ignitor

rectly

 

Not pausing long enough before clicking the control panel knob

No spark

LP gas cylinder is empty

Coupling nut is not fully con- nected to regulator

Excess flow valve tripped in regulator

Obstructions in burners

Electrodes and burners are wet

Wire is loose or disconnected

Wire is shorting (sparking between ignitor and elec- trode)

When lighting the 1st (Leftmost) Burner, push-in and turn con- trol panel knob counter-clockwise until you feel resistance with turning. Pause 4 seconds with knob still pushed in, then contin- ue turning knob counter-clockwise until a click is heard

Gas collector tab is bent (making too large or small of a gap between electrode and tab). By hand, bend gas collector tab back within a maximum of 3/16” gap to electrode. (See page 19 for illustration).

Take LP gas cylinder to licensed LP gas supplier to be refilled

Tighten coupling nut by hand about one-half to three quarters additional turn. Do not use tools.

Turn control knobs to “off” position and turn LP gas cylinder handle clockwise until it stops. Wait five minutes. Relight LP gas grill.

Clean burners (See Burner Maintenance in Care and Maintenance section of this manual)

Dry electrode with clean cloth

Reconnect the wire

Replace ignitor wire/electrode assembly (Call the Customer Service Department)

Burners will not light

Burners not assembled cor-

See Step 9 - Install Burners page of the Assembly Instructions

using a match

rectly

 

 

LP gas cylinder is empty

Take LP gas cylinder to licensed LP gas supplier to be refilled

 

Excess flow valve tripped in

Turn control knobs to “off” position and turn LP gas cylinder

 

regulator

handle clockwise until it stops. Wait five minutes. Relight LP

 

 

gas grill.

 

Coupling nut is not fully con-

Tighten coupling nut by hand about one-half to three quarters

 

nected to regulator

 

 

Obstructions in burners

Clean burners (See Burner Maintenance in Care and

 

 

Maintenance section of this manual)

 

 

 

Low flame or low heat

Gas in LP cylinder is low

Check LP gas cylinder. Refill if necessary.

 

Excess flow valve tripped in

Turn control knobs to “off” position and turn LP gas cylinder

 

regulator

handle clockwise until it stops. Wait five minutes. Relight LP

 

 

gas grill. If flame remains to be low, turn off gas at cylinder and

 

 

grill. Disconnect the regulator from the LP gas cylinder.

 

 

Reconnect the regulator to the LP gas cylinder. Perform a leak

 

 

test. Relight grill. This will reset the excess flow valve.

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone PART/DESCRIPTION BonzaKanga Bonza QTY Kanga Bonza PART/ DescriptionPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcs Wheel LEG/ Side Table Assembly ToolsItem 9 8 pcs Fixed LEG/SIDE Table Assembly ToolsItem 10 8 pcs Tear Drop Table ShownX 1 Bolt 8 pcs Pcs Legbrace Assembly ToolsItem 19, 20 Bottom SHELF/LEG & Caster Assembly ToolsX 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt Metal X 2 Bolt Wood 1/4 X 1 3/8 Bolt MetalItem 23, 24 WHEEL/ Cylinder Bracket Assembly ToolsItem 27 4 pcs X 1/2 BoltAssembly Next Grill BODY/CART ASSEMBLY- Kanga Models ToolsItem 30 Spacer 8 pcs Item 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUT6mm X 110mm Assemble Grill Body to CART- Kanga ModelsGrill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models Tools Item 32 6mm Wing NUT 8pcsItem 31 Actual Size 6mm x 110mm Bolt Pcs Grill BODY/CART ASSEMBLY- Bonza Models Continue Assembly of Bonza & Bonza Deluxe Models AT Step6mm x 110mm Bolts Attach Decorative Privacy Panel to Cart ALL Models Install Burner ToolsNext Or 4 PCSAdjust Tab if greater than 3/16 Cotter PIN Install from underneath Backside of grill16 GAP Install Bottom Body PANEL/GREASE TRAY- ALL Models Install Ceramic Briquette Trays & Grids ALL Models#8 X 1/2 Screw 2pcs Attach Handle to Weather Cover LID Kanga Models Tools SCREW, #10 X 3/8#10 X 3/8 Screw Attach Handle and Heat Indicator to Hood Bonza Models Tools FIG. K Attach LP Cylinder to Grill ALL ModelsHow to perform a leak test Leak Testing to be Performed in a WELL-VENTILATED AreaConnecting/ Disconnecting LP Gas Cylinder to Grill GAS, CYLINDER, Hose Regulator InformationLP Gas Cylinder Before Using Your LP GAS Grill PrecautionsSelecting a Location Operating the LP GAS Grill LeakTestingPreparation Before Cooking Lighting the Grill Using the Integra Spark Ignition SystemTurn LP cylinder handle counter-clockwise on Confirm each burner is lit before lighting another burnerManual Lighting of the Grill Check Your Flame End of Cooking Session Care and MaintenanceTurn off Your LP Gas Grill Grill CookingHow to clean procelain coated cast iron burners Burner MaintenancePreventive Maintenance Cleaning the Grill BodyCeramic Briquettes Bottom Panel/ Grease TrayUsing a match Using the ignitorBurners will not light Low flame or low heatFlames blow out Flare upPersistent grease fire Important Notice Aussie Grill Company Limited Warranty
Top Page Image Contents