Aussie Kanga, Bonza Deluxe owner manual Attach LP Cylinder to Grill ALL Models, Fig. K

Page 23

STEP 14-ATTACH LP CYLINDER TO GRILL - (ALL MODELS)

•Fill empty LP Cylinder at your local LP gas supplier.

•Set bottom ring of LP Cylinder into Cylinder Bracket through round hole in Bottom Shelf (Fig. K ). Turn Adjusting Knob clockwise to secure LP Cylinder inside Cylinder Bracket(Fig. K).

•Turn all control knobs and LP Cylinder valve to the “Off” position.

•Take the protective cap off the cylinder valve. (Fig. L) Hold Regulator in a straight line with LP Cylinder valve so the connection does not cross thread. Insert nipple into the cylinder valve. Hand tighten coupling nut in clockwise direction. Do not use tools.

•Make sure Regulator hose does not contact hot metal surfaces.

WARNING: Do not use grill if this connection can not be completed. Be sure to test this connection for gas leaks before operation of Gas Grill.

ROUTE HOSE UNDER	ROUTE HOSE ON
BRACE ON MODELS	OUTSIDE OF LEG ON
WITH WOODEN LEGS	ALL MODELS

LP

CYLINDER

FIG. K

ADJUSTING

KNOB

		LP GAS
		VALVE
REGULATOR		VALVE

FIG. L

	TURN REGULATOR COUPLING
	TURN REGULATOR COUPLING		PROTECTIVE CAP
	NUT CLOCKWISE TO TIGHTEN		PROTECTIVE CAP
	NUT CLOCKWISE TO TIGHTEN

23

Image 23

Contents AussieTM Important Safeguards Page Am 5 pm E.S.T Mon. Fri Telephone Kanga Bonza PART/DESCRIPTIONBonza QTY Kanga Bonza PART/ DescriptionPART/ Descripton PART# QTY. Kanga Bonza 47 6mm Item 1, 2, or 4 Side Table X 1 3/8 Bolt 8pcs X 1 Bolt 8 pcs Wheel LEG/ Side Table Assembly ToolsTear Drop Table Shown Fixed LEG/SIDE Table Assembly ToolsItem 9 8 pcs Item 10 8 pcsX 1 Bolt 8 pcs Pcs Legbrace Assembly ToolsX 2 Bolt Wood 1/4 X 1 3/8 Bolt Metal Bottom SHELF/LEG & Caster Assembly ToolsItem 19, 20 X 1 Bolt Wood LEG 1/4 x 1 3/8 Bolt MetalX 1/2 Bolt WHEEL/ Cylinder Bracket Assembly ToolsItem 23, 24 Item 27 4 pcsItem 31 6mm x 110mm Bolt 8 pcs Item 32 6mm Wing NUT Grill BODY/CART ASSEMBLY- Kanga Models ToolsAssembly Next Item 30 Spacer 8 pcs6mm X 110mm Assemble Grill Body to CART- Kanga ModelsItem 31 Actual Size 6mm x 110mm Bolt Pcs Grill BODY/CART ASSEMBLY- Bonza & Bonza Deluxe Models ToolsItem 32 6mm Wing NUT 8pcs 6mm x 110mm Bolts Grill BODY/CART ASSEMBLY- Bonza ModelsContinue Assembly of Bonza & Bonza Deluxe Models AT Step Or 4 PCS Install Burner ToolsAttach Decorative Privacy Panel to Cart ALL Models Next16 GAP Adjust Tab if greater than 3/16Cotter PIN Install from underneath Backside of grill #8 X 1/2 Screw 2pcs Install Bottom Body PANEL/GREASE TRAY- ALL ModelsInstall Ceramic Briquette Trays & Grids ALL Models #10 X 3/8 Screw Attach Handle to Weather Cover LID Kanga Models ToolsSCREW, #10 X 3/8 Attach Handle and Heat Indicator to Hood Bonza Models Tools FIG. K Attach LP Cylinder to Grill ALL ModelsHow to perform a leak test Leak Testing to be Performed in a WELL-VENTILATED AreaLP Gas Cylinder Connecting/ Disconnecting LP Gas Cylinder to GrillGAS, CYLINDER, Hose Regulator Information Selecting a Location Before Using Your LP GAS GrillPrecautions Operating the LP GAS Grill LeakTestingConfirm each burner is lit before lighting another burner Lighting the Grill Using the Integra Spark Ignition SystemPreparation Before Cooking Turn LP cylinder handle counter-clockwise onManual Lighting of the Grill Grill Cooking Care and MaintenanceCheck Your Flame End of Cooking Session Turn off Your LP Gas GrillHow to clean procelain coated cast iron burners Burner MaintenanceBottom Panel/ Grease Tray Cleaning the Grill BodyPreventive Maintenance Ceramic BriquettesLow flame or low heat Using the ignitorUsing a match Burners will not lightPersistent grease fire Flames blow outFlare up Important Notice Aussie Grill Company Limited Warranty