Pride Mobility Outlander DE, Outlander LP, Outlander XL manual Battery Replacement

Page 19

V . B A T T E R Y C H A R G I N G

BATTERY REPLACEMENT

WARNING! Battery posts, terminals, and related accessories contain lead and lead compounds. Wear goggles and gloves and wash hands after handling.

MANDATORY! Use only AGM or Gel-Cell batteries to reduce the risk of leakage or explosive conditions.

WARNING! Corrosive chemicals contained in battery.

WARNING! Keep tools and other metal objects away from battery terminals. Contact with tools can cause electrical shock.

WARNING! Connect the battery harnesses in the proper manner. RED (+) cables must be connected to positive (+) battery terminals/posts. BLACK (-) cables must be connected to negative (-) battery terminals/posts. REPLACE cables immediately if damaged. Protective caps must be installed over all battery terminals.

NOTE: If you encounter a damaged or cracked battery, immediately enclose it in a plastic bag and contact your local waste disposal agency or your authorized Pride Provider for instructions on disposal and battery recycling, which is our recommended course of action.

Follow these steps to replace the onboard battery (see figure 21):

1.Unfasten the battery securement strap located at the bottom of the battery box.

2.Remove the hardware from the battery securement bracket and remove the bracket.

3.Remove the hardware from the battery connector.

4.Slide the battery out of the battery box to expose the battery harness.

5.Disconnect the battery harnesses from the bat- tery terminals.

6.Connect the battery harnesses to the new battery.

7.Slide the new battery into the battery box.

8.Reinstall the hardware to secure the battery connector and tighten.

9.Reinstall the battery securement bracket and tighten the hardware.

10.Refasten the battery securement strap.

BATTERY BOX

BATTERY SECUREMENT STRAP

BATTERY SECUREMENT BRACKET

BATTERY CONNECTOR

Figure 21. Battery Replacement

Outlander Series

www.pridemobility.com

19

Image 19

Contents Outlander Series F E T Y G U I D E L I N E S N T E N T S Information Exchange N T R O D U C T I O NInternet and Private Purchases PURCHASER’S Agreement Shipping and DeliveryS a F E T Y Product Safety SymbolsS a F E T Y S a F E T Y Operator Positioning Lifting Capabilities InstallationLifting NON-PRIDE Products Prelift InspectionHitch Classes Hitch Class InformationLift System Installation I . InstallationTension Bolt and Clevis Pin Adjustment Follow these steps to install the lift systemFollow these steps to route the lift system wiring harness Wiring Harness InstallationFollow these steps to install the onboard battery Onboard Battery InstallationLicense Plate Holder Follow these steps to install the wheel chocks Wheel Chock InstallationSee figure Loading and Securing Your Mobility Device O P E R a T I O NLift System Operation Follow these steps to operate the lift systemUnlocking the Retractable Tie-down Strap Manual Lift System Operation Power Chair Hold-down BarFollow these steps to charge the onboard battery Battery ChargingA T T E R Y C H a R G I N G Follow these steps to replace the onboard battery see figure Battery ReplacementC a R E a N D M a I N T E N a N C E Care and MaintenanceLift Removal General Cleaning GuidelinesWiring Harness Lift Platform/Metal ComponentsWhat if the lift system operates slowly up or down? I . TroubleshootingTroubleshooting What if the motor on my lift system will not operate?I I . W a R R a N T Y THREE-YEAR Transferable Limited WarrantyONE-YEAR Warranty Service Checks and Warranty ServiceSpecifications P E N D I X I Specification SN S I G N E S D E S E C U R I T E B L E D E S M a T I E R E S Transport ET Reception Achat Prive ET PAR Internet Convention a LachatEchange D’INFORMATIONS Pictogrammes DE Securite S E C U R I T ES E C U R I T E S E C U R I T E Positionnement DE L’OPERATEUR Puissance DE LevageLevage D’UN Produit NON-PRIDE Inspection Avant LevageClasses d’attelage Information SUR LES Attelages DE RemorqueInstallation du bras de blocage Installation DU Systeme DE LevageRéglage du boulon de tension et de la broche Installation du câblage Installation du câblageVoici les étapes pour installer la batterie interne Installation de la batterie interneSupport de plaque d’immatriculation Voici les instructions d’installations des cales de roues Installation des cales de rouesFonctionnement DU Systeme DE Levage F O N C T I O N N E M E N TEmbarquement et ancrage de votre appareil de mobilité Outlander Series Barre de blocage pour fauteuil motorisé Fonctionnement Manuel DU Systeme DE LevageRecharge DES Batteries E C H a R G E D E S B a T T E R I E SVoir la figure Remplacement d’une batteries Remplacement D’UNE BatteriesCédule d’entretien 2 ans S O I N S E T E N T R E T I E NSoins ET Entretien Programme d’entretien 90 joursEnlèvement de l’appareil de levage Consignes pour le nettoyageCâble de batterie Plateforme/ Composantes en métalI . P R O B L E M E S E T S O L U T I O N S Problemes ET SolutionsQue faire si mon appareil fonctionne au ralenti seulement? Garantie DE UN AN Service ET Reparation Sous GarantieI I . G a R a N T I E Garantie Limitee Transferable DE Trois ANSN E X E I Specification S INFMANU3882