Invacare X-Terminator QR, X-Terminator Titanium Inspect/Adjust Weekly, Inspect/Adjust Monthly

Page 25

SECTION 3—SAFETY INSPECTION

Inspect wheel/fork assembly for proper tension by spinning caster; caster should come to a gradual stop.

Loosen/tighten locknut if wheel wobbles noticeably or binds to a stop.

Ensure wheel bearings are clean and free of moisture.

Inspect tires for flat spots and wear.

If pneumatic tires check for proper inflation.

Check that all labels are present and legible. Replace if necessary.

Inspect/Adjust Weekly

Ensure hand grips (if equipped) are not loose.

Ensure quick release axles and camber inserts are clean.

Ensure quick/quad release axles lock properly.

Inspect handrims for signs of rough edges or peeling.

Inspect spokes for bent or broken spokes.

Ensure All spokes uniformly tight.

CAUTION

As with any vehicle, the wheels and tires should be checked periodically for cracks and wear, and should be replaced if damaged.

Inspect wheel/fork assembly for proper tension by spinning caster; caster should come to a gradual stop.

Inspect tires for flat spots and wear.

Ensure that casters are free of debris.

If pneumatic tires check for proper inflation.

Inspect/Adjust Monthly

Ensure wheel locks DO NOT interfere with tires when rolling.

Ensure pivot points are free of wear and looseness.

Inspect upholstery fastening flaps to ensure they securely latch.

Ensure that casters are free of debris.

Inspect seat positioning strap for any signs of wear. Ensure buckle latches. Verify hardware that attaches strap to frame is secure and undamaged. Replace if necessary.

Ensure adjustable axle position camber bar is securely tightened.

Part No 1114851

25

Everyday and Sport Series Wheelchairs

Image 25
Contents Everyday and Sport Series Wheelchairs Everyday and Sport Series Wheelchairs Table of Contents Wheels Suspension Complete and mail the form on the next Register Your ProductProduct Registration Form Fold Here Cut Along Line Wheelchair TIE-DOWN Restraints and Seat Positioning Straps Special NotesTerminator Typical Product ParametersTypical Product Parameters Terminator Titanium Titanium Paul Schulte Signature BB Transformer ALL-SPORT Stability Warning General GuidelinesOperating Information General Guidelines Weight Limitation Weight TrainingTire Pressure and Information Stability and Balance Safe HandlingCoping with Everyday Obstacles Percentage of Weight DistributionReaching, Leaning Backwards Reaching, Leaning and Bending ForwardTipping Curbs TippingStairways Transferring To and From Other Seats Safety Inspection Checklist Safety InspectionInspect Initially Inspect/Adjust Monthly Inspect/Adjust WeeklyInspect/Adjust Periodically TroubleshootingMaintenance Safety Precautions MaintenanceSuggested Maintenance Procedures Safety Inspection Back Back Angle AdjustmentUnfolding/Folding the Back Back Angle Adjustment Installing Foldover Back Upholstery Removing/Installing Foldover Back UpholsteryRemoving Foldover Back Upholstery Adjustable Tension Straps Adjustable Tension Back UpholsteryReplacing Adjustable Tension Back Upholstery Back Upholstery CoverBack Height Adjustment Adjustable Backs Only Back Original Back Height in Inches Wheels Removing/Installing Rear WheelsReplacing Quad-Release Axles Adjusting Quick-Release AxlesAnd/or Out Adjusting Quad-Release HandlesRemoving Play from Rear Wheels Repairing/Replacing Rear Wheel, Tire/Tube Handrim ReplacementOpening/Closing Camber Clamps Opening/Closing Camber Clamps Camber Tube Adjusting Rear Wheel CamberA4 Camber System Determining Toe In/Toe Out Adjusting Toe In/Toe Out Camber Tube Adjusting Toe In/Toe OutCourse Adjustment Fine Adjustment 11 Adjusting Toe In/Toe Out A4 Camber System Fine Adjustment Adjusting Wheelbase Length Adjusting Center of Gravity12 Adjusting Wheelbase Length Adjusting Center of Gravity 13 Adjusting Wheelbase Width Camber Tube Adjusting Wheelbase WidthReplacing Axle Tube 14 Adjusting Wheelbase Width A4 Camber SystemWheels Adjusting the Axle Tube 16 Adjusting the Axle Tube Camber Tube 17 Adjusting the Axle Tube A4 Camber System Repeat Steps 1‐3 for the opposite caster if necessary Replacing/Adjusting CastersParallel to the floor Adjusting Front Caster HeightWheel Lock Adjustment/Replacement 20 Wheel Lock Adjustment/Replacement Seat Replacing Adjustable Tension Seat UpholsteryReplacing Screw-On Seat Upholstery Replacing Adjustable Tension Seat UpholsteryAdjusting Front Seat Height Adjusting Transformer Seat HeightAdjusting Rear Seat Height Adjusting Transformer Seat Height Footrest ANTI-TIPPER Adjusting the FootrestReplacing the Footrest Replacing/Adjusting Optional A4 Footrest Installing/Adjusting Optional Clamp on Raised FootrestInstalling AdjustingAdjusting Footplate Angle Installing the X-Terminator FootrestAdjusting Footplate Depth Depth Adjusting the X-terminator and Transformer FootrestsAngle Terminator HeightAdjusting/Replacing Anti-tipper Replacing Anti-tipper Adjusting Anti-tipperInstalling/Depth Adjustment Installing/Removing/Adjusting Swivel Anti-TipRemoving Paul Schulte Signature BB and T-5 Tennis Elite Models only Adjusting HeightElastomers and Suspension Replacing Rear Elastomers SuspensionReplacing Rear Elastomers Replacing Front ElastomersReplacing Front Elastomers WING/BUMPER Installing/Removing the Wing/BumperWING/BUMPER Limited Warranty USA