Invacare Arrow Replacing Seat Mounting Plates Figure, Replacing Seat Support Brackets Figure

Page 33

BASE FRAME

PROCEDURE 7

 

 

This Procedure Includes the Following:

Replacing Seat Mounting Plates

Replacing Seat Support Brackets

Replacing Seat Support Bracket T-Nuts

Replacing Battery Charger Bracket and T-Nut

Removing/Installing Seat Stop Screws

WARNING

After ANY adjustments, repair or service and BE- FORE use, make sure that all attaching hardware is tightened securely - otherwise injury or dam- age may result.

REPLACING SEAT MOUNTING PLATES (FIGURE 1)

NOTE: When replacing components of the wheelchair, refer to the individual procedure for correct use of LOCTITE 242 and torque specifications or PROCEDURE 3 of this Manual.

1.Perform the instructions outlined in PREPARATIONS FORREMOVING/INSTALLINGSEATFRAME(STAN- DARD FRAME, ADJUSTABLE FRAME, AND CAP- TAINS VAN SEAT) in PROCEDURE 6 of this manual.

2.Perform one (1) of the following:

A.Remove standard seat frame subassembly. Refer to REMOVING/INSTALLING STANDARD SEAT FRAME SUBASSEMBLY in PROCEDURE 6 of this manual.

B.Remove adjustable seat frame subassembly. Re- fer to INSTALLING/REMOVING ADJUSTABLE SEAT FRAME ASSEMBLY AND OR COMPO- NENT REPLACEMENT in PROCEDURE 6 of this manual.

C.Remove captains van seat. Refer to INSTALLING/ REMOVINGCAPTAINSVANSEATASSEMBLYin PROCEDURE 6 of this manual.

NOTE: Before removing seat mounting plates, note the po- sitionofthewashers.

3.Remove the two (2) mounting screws, washers and boltstrap bracket thatsecure theseat mountingplateto the seat support bracket.

4.Secure NEW seat mounting plate with existing two (2) mounting screws, washers, and bolt straps to seat sup- port bracket using Loctite 242 and torque to 156-inch pounds.

5.Repeat STEPS 1-2 for opposite side, if necessary.

NOTE: For illustrations of the three (3) different seat mount- ing plates, refer to MOUNTING PLATE - SEAT ANGLE ADJUSTMENT AND INSTALLATION ORIENTATION in PROCEDURE 6 of this manual.

6.Adjust seat mounting plates to desired angle. Refer to

MOUNTING PLATE - SEAT ANGLE ADJUSTMENT ANDINSTALLATIONORIENTATIONinPROCEDURE 6 of this manual.

7.Reverse STEP 2A, 2B or 2C.

8.Perform the instructions outlined in PREPARATIONS FORREMOVING/INSTALLINGSEATFRAME(STAN- DARD FRAME, ADJUSTABLE FRAME, AND CAP- TAINS VAN SEAT) in PROCEDURE 6 of this manual.

Washer

Bolt Strap

Seat

MountingMounting

PlateScrews

Seat

Support

Bracket

Washer

Mounting

Screws

FIGURE 1 - REPLACING SEAT MOUNTING PLATES

REPLACING SEAT SUPPORT BRACKETS (FIGURE 2)

1.PerformtheinstructionsoutlinedinPREPARATIONSFOR REMOVING/INSTALLINGSEATFRAME(STANDARD FRAME,ADJUSTABLE FRAME,ANDCAPTAINSVAN SEAT) in PROCEDURE 6 of this manual.

2.Performone(1)ofthefollowing:

A.Remove standard seat frame subassembly. Refer to REMOVING/INSTALLING STANDARD SEAT FRAMESUBASSEMBLYinPROCEDURE6ofthis manual.

B.Remove adjustable seat frame subassembly. Re- fer to INSTALLING/REMOVING ADJUSTABLE SEAT FRAME ASSEMBLY AND OR COMPO- NENT REPLACEMENT in PROCEDURE 6 of this manual.

C.Remove captains van seat. Refer to INSTALLING/ REMOVINGCAPTAINSVANSEATASSEMBLYin PROCEDURE 6 of this manual.

3.Removeseatmountplates.RefertoREPLACINGSEAT MOUNTINGPLATESinthisprocedureofthemanual.

NOTE: Note the position of the seat support brackets before removingtoensureproperreinstallation.

B A S E

F

R A M E

33

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Storm Series Wheelchairs E C I a L T E S I N GTable of Contents Table of Contents Limited Warranty Specifications Specification SArrow FWD has a 400 lb. rating SpecificationsRepair or Service Information Procedure General GuidelinesMOTOR/GEARBOX General Guidelines ProcedureFWD Models MWD ModelsSuspension Arm Located on insideTroubleshooting Procedure Using Hydrometer to Check Battery Cells Lead Acid FigureBattery Charger Connector Digital Voltmeter Field Load Test FigureProcedure Troubleshooting Motor Testing FigureNumber of Floating Balls Will Vary According to ChargeOhmmeter Motor Connector ELECTRO-MECHANICAL Parking Brake Testing FigureCap Motor Pin Motor Connector Cap Motor Pin Motor Connector OhmmeterStandard Seat Frame Hardware Torque SpecificationsHardware Torque Specifications Procedure Adjustable Seat FrameCaptains VAN Seat Loctite and Torque to 75 in/lbs Torque to 156 in/lbsWheel Halves Inch WheelsPneumatic with Flat-Free Wheel Halves Torque to Pneumatic Wheel Halves 8 inch Torque to 18 in/lbsPneumatic Wheel Halves Pneumatic with Flat-FreeTorque to 156 in/lbs 1020 in/lbs Torque to 156 in/lbs Torque to 160 in/lbs LoctiteTorque to 360 in/lbs Torque to 156 in/lbs This Procedure Includes the Following Arms ProcedureReplacing Captains VAN Seat Armrest Plate Figure Replacing Armrest Pads Captains VAN Seats FigureReplacing Back Upholstery Figure Replacing Seat Positioning Strap Captains VAN Seats FigureH O L S T E R Y Van Seat Frame Seat Positioning StrapΥSPREADER BAR Inches ΥSPREADER BARΥHeight of Spreader Bar from Bottom of Back Canes to Top of Spreader Bar ClampM E Seat Frame Procedure REMOVING/INSTALLING Standard Seat Frame Subassembly FigureReplacing Exact Same Size Standard Seat Frame RemovingSeat Frame Adjustable Seat Frame FigureInches Inch Inch deep InchesA T M E Torque toChanging Seat Depth Between 12 and 15- Inches Figure Brackets, note the Back Angle for reinstallation Changing Seat Width Standard and Adjustable Seat FrameWheelchair to hold the insert in place Mounting Screws Torque to 75-inch poundsSide Spacers Center Seat WidthMounting Screws Component ReplacementCoved Washer Center FrameInstalling Captains Van Seat INSTALLING/REMOVING Captains VAN Seat Assembly FigureRemoving Captains Van Seat Torque to 75-inchAdjustable Frames Remove the captains van seatAssembly. Refer toPerform one 1 of the following sections Perform the instructions outlined in PreparaREMOVING/INSTALLING Seat PAN Figure InstallingRemove the seat cushion from the seat pan Seat Angle Adjustment Installation OrientationSeat Dump Mount Replacing Seat Mounting Plates Figure Base Frame ProcedureReplacing Seat Support Brackets Figure S E M EReplacing Seat Support Bracket T-NUTS Figure Procedure Base FrameBattery Charger Connector Mount Replacing Battery Charger Bracket and T-NUTRWD and MWD Models Figure Arrow FWD Model FigureMounting Screw Battery Charger Connector Bracket Base Frame REMOVING/INSTALLING Seat Stop Screws FigureSeat Support Bracket Base Frame Stop Screw Front Seat Stop ScrewBack Frame Procedure REMOVING/INSTALLING CJ Back Brackets FigureC K CJ Bracket mounts Front Holes on Back Angle Detail a PlatesRemove the back assembly from the wheelchair Procedure Back FrameHeavy Duty Models Mine if new back upholstery is neededSteps 6,11 Steps 2Steps 6,17 Steps 4,8Back Angle Adjustment Figure T T E Batteries ProcedureProcedure 9BATTERIES Connecting Battery CablesT T E R I E S Group 24 BatteriesDetail a Battery Box BottomGroup 22 Battery Base Frames Figure Remove battery terminal caps from batteryTerminals ends. Refer to Detail a in Figure Bottom Tery Cable Rear Jumper Battery Single BatteryFront BoxBattery Discharge Indicator BDI Battery Discharge Indicator BDI in LCD ReadoutDescription and Use of Battery Chargers Charging Batteries FigureRequired Items If one 1 battery is defective INSTALLING/REMOVING Group 24 Battery Boxes FigureRecommended Battery Types Cleaning Battery TerminalsINSTALLING/REMOVING Group 22 Battery BOX Figure REMOVING/INSTALLING the E Wiring Harness Figure Procedure Wiring HarnessThis manual E S S Recline Angle 4 inches 61o Adjusting Limit Switch FigureReplacing Retainer Bar Retention STRAP/RETAINERReplacing Retainer Clip Perform one 1 the followingSpacer Locknuts Mounting Screws Battery Box Sub-Frame ProcedureSpacer Retainer Retainer ClipReplacing Pneumatic Tires REMOVING/INSTALLING Drive Wheels FigureTubes Drive WHEELS/CASTERS WHEELS/ MotorsREMOVING/INSTALLING Drive Wheel HUB Figure Installing Casters REMOVING/INSTALLING Casters FigureReplacing Forks Figure WHEELS/MOTORSMotor Connector Coupling Allen Locknut SpacerWasher Shock Remove motor with motor lock lever from suspen- sion arm Brake Release Shaft REMOVING/INSTALLING Motor GEARLESS/BRUSHLESSRepositioning Mkiv Joystick VAN Seat Models Figure REMOVING/INSTALLING Mkiv Controller FigureElectronics E C T R O N I C SArrow Fwd Model Base Frame SpacerMounting Screw Shock Switch Washers Actuator Overtighten Positioning Limit Switch FigureRecliner C L I N E RGas Cylinder Replacing Recliner Cable Assemblies FigureRod Measures 21/32-inches Mounting Screws and Washers Do not Over-Tighten Gas Cylinder ActuatorReplacing Gas Cylinder REPLACING/ADJUSTING GAS Cylinders FigureProcedure Recliner Adjusting Gas CylinderChanging Back Height Seat Pan Removal/Replacement Procedures Recliner ProcedureChanging Seat Depth Figure Changing Seat WidthPlate Inside Suspension Arm Assembly Remove seat pan on reclinerSpacer Base Frame Seat Mount REMOVING/INSTALLING Group 22 Battery BOX Tray Figure REMOVING/INSTALLING GroupBattery BOX SUB-FRAME Figure MWD Wheelchairs ProcedureFront Locknuts Battery Mount Procedure MWD WheelchairsInstalling Group 24 Components Figure Frame Rear LocknutsBattery Box Shock ReplacementGroup 24 Battery Base Frames Figure StepsMounting Screw Spring Washer Shock Battery Box Sub-Frame Retainer Clip Top of ShockBase Frame Mounting Shock Screw Inner Link Spacer Suspension ArmBattery Mount Bracket Base Frame Shock Spring Replacement FigureMounting Screw Suspension Arm Spring Washer Shock LocknutReplacing Stabilizer Fork Assembly Figure Replacing Stabilizer Wheels FigureShock Spring Base MWD Wheelchairsprocedure Adjusting Weight DistributionReplacing Stabilizer Cylinder Spring FigureAdjusting Stabilizers Figure Height AdjustmentAdjusting Spring Compression Replacing Suspension ARM Figure REMOVING/INSTALLING Gearbox Figure16-18 x 1-1/4-inch Mounting Screws 16-18 x 2-1/2-inch Motor Gearbox Suspension ArmTubular End Suspension Arm Steps 6,10Bracket End Suspension Arm Inner Link Spacer Mounting Screw Shock Replacement REMOVING/INSTALLING Group 22 Battery BOX Tray FigureAnti-Tipper Wheel Replacement Age may resultBattery Tray Procedure RWD WheelchairsRubber ElementRWD Wheelchairs Procedure Shock Replacement FigureSpacer Retainer Clip Or Rubber ElementShock Retainer Bar Spacer TopShock Mounting Screw Suspension Arm Locknut Shock Mounting Screw Suspension ArmBattery BOX or INSTALLING/REMOVING RWD WheelchairsprocedureSpacer Clip is against the battery box retainer This manual Shock Eyelet Assembly Retainer Spring BaseRubber Element Replacement Figure Shock Hex Screw Battery Mount BracketBase Frame Mounting Screw Adjusting Weight Distribution Figure REMOVING/INSTALLING GearboxAdjustment Options 16-18 2-inch 4-inchAdjusting Weight Distribution Procedure AssemblyRepositioning the MOTOR/ Gearbox Figure Mounting Screws Washer Seat Support Bracket Base FrameRepositioning the GEARLESS/BRUSHLESS Motor ,14 Standard Position Lengthens the wheelInch Rearward Lengthens the wheelbase Batterybase Frames in Procedure 9 This manual Brushless Motor in this procedure of theW ManualSecurely tighten adjustment screw Suspension Arm Mounting Washer ScrewsInstructions ANTI-TIPPER Wheel Replacement FigureCharger cable to the suspension arm Anti-Tipper Wheel Spacer LocknutAnti-Tip REMOVING/INSTALLING ANTI-TIP AssemblyLower Washers LocknutsREMOVING/INSTALLING Rear Shroud Figure REMOVING/INSTALLING Front Shroud FigureREMOVING/INSTALLING Side Shroud Assembly Figure FWD Wheelchairs ProcedureFWD Wheelchairs REMOVING/INSTALLING Counterweight FigureHandle Outside LowerEdgeCounterweight Replacing Group 24 Battery BOX SUB-FRAME FigureMounting Bracket Counterweight Bottom Shoulder Screw Bottom Shoulder Screw Bottom Slot in Mounting BracketProcedure FWD Wheelchairs REMOVING/INSTALLING Shocks FigureAdjusting/Installing TIE ROD Replacement FigureIng tie rods Battery wiring harness Detail C Sensor Cable Assembly Replacement FigureRemove the Existing sensor cable assembly Socket Suspension Screw ArmSHORT Motor GearboxTie Wrap C Battery Box Sub Frame Sensor WasherReplacing the Suspension ARM REMOVING/INSTALLING Wiring Harness FigureCurelyTighten ChargerporttothemountingbracketDETAILA.SeTie Wrap B Tie Wrap aAdjusting Weight Distribution For New Seat Depth Mounting Screws Seat Support Brackets Front14 to 16 inches Inches 17 to 18 inches 19 to 20 inches Depth Footboard ADJUSTMENTS- DEPTH/HEIGHT/ANGLE FigureAngle HeightFlat Screws Footrest Angle AdjustmentsMounting Positions Hub CapRight FWD Wheelchairs ProcedureHorizontal Position Cam Front Shroud Footrest105 106 Limtied Warranty Limited Warranty
Related manuals
Manual 222 pages 55.68 Kb
Top Page Image Contents