Invacare Ranger X, Arrow, Torque SP ANTI-TIPPER Wheel Replacement Figure, Instructions

Page 89

RWD WHEELCHAIRS

PROCEDURE 16

 

 

8.Torque suspension arm hex screws (1/2 x 7-inches) to 85 FOOT pounds (approximately 1,020-inch pounds) and replace plug buttons.

9.Reinstallthegearboxontotheexistingsuspensionarm. RefertoREMOVING/INSTALLINGGEARBOXinthis procedure of the manual.

10.Tighten the hex screws that secure wiring harness to sub-frame assembly securely.

11.Reinstall the drive wheel onto the wheelchair. Refer to REMOVING/INSTALLINGDRIVEWHEELSinPRO- CEDURE 12 of this manual.

12.RepeatSTEPS1-12fortheoppositesideofthewheel- chair, if necessary.

REPLACING SUSPENSION ARM FOR WHEELCHAIRS WITH GEARLESS/BRUSHLESS MOTORS (FIGURE 16)

1.

Perform one (1) of the following:

 

A. Remove the seating system. Refer to the seating

 

systems owner’s manual for removal/installation

 

instructions.

 

B. Remove the seat pan. Refer to REMOVING/IN-

 

STALLINGTHESEATPANinPROCEDURE6of

 

this manual.

2.

Removethemotor.RefertoREMOVING/INSTALLING

 

THE MOTOR in PROCEDURE 12 of this manual.

3.

Cut the tie-wrap(s) that secure the wiring harness/

 

charger cable to the suspension arm.

4.

Remove the anti-tip assembly from the rear of the sus-

 

pensionarm.RefertoREMOVING/INSTALLINGTHE

 

ANTI-TIPASSEMBLYinthisprocedureofthemanual.

5.

Remove the shock from the suspension arm. Refer to

 

REMOVING/INSTALLINGTHESHOCKASSEMBLY

 

in this procedure of the manual.

6.

Remove the plug buttons from the side of the base

 

frame.

12.Install the shock onto the new suspension arm. Refer to REMOVING/INSTALLING THE SHOCK ASSEM- BLY in this procedure of the manual.

13.Install the motor onto the new suspension arm. Refer to REMOVING/INSTALLING THE MOTOR in PRO- CEDURE 12 of this manual.

14.Install anti-tip assembly onto the rear of the new sus- pensionarm.RefertoREMOVING/INSTALLINGTHE ANTI-TIPASSEMBLYinthisprocedureofthemanual.

15.Perform one (1) of the following:

A.Remove the seating system. Refer to the seating systems owner’s manual for removal/installation instructions.

B.Remove the seat pan. Refer to REMOVING/IN- STALLINGTHESEATPANinPROCEDURE6of this manual.

Suspension Arm

Beveled

Washers

Plug

Button

Suspension Arm Hex Screw

(1/2 x 7-inches)

FIGURE 16 - REPLACING SUSPENSION ARM FOR WHEELCHAIRS WITH GEARLESS/BRUSHLESS MOTOR

ANTI-TIPPER WHEEL

REPLACEMENT (FIGURE 9)

1.Remove the locknuts, hex screws and spacers that securetheanti-tipperwheelstotheshockmountplates.

2.Replace anti-tipper wheel(s) and torque existing hard- ware to 30-35-inch pounds. DO NOT overtighten.

R W D

W H E E L C H A I R S

7.

Remove the mounting screw and beveled washers

 

that secure the front of the suspension arm to the base

 

frame.

8.

Remove the existing suspension arm from the base

 

frame.

9.

Install the new suspension arm onto the base frame.

10.

Install mounting screw and beveled washers that se-

Anti-Tipper Wheel

Spacer

Locknut

curethefrontofthesuspensionarmtothebaseframe.

11. Install the plug buttons into the side of the base frame

Hex Screw Shock Mount Plates

FIGURE 9 - ANTI-TIPPER WHEEL REPLACEMENT

89

Page 88 Page 90
Image 89
Page 88 Page 90
Contents Storm Series Wheelchairs E C I a L T E S I N GTable of Contents Table of Contents Limited Warranty Specifications Specification SArrow FWD has a 400 lb. rating SpecificationsRepair or Service Information Procedure General GuidelinesMOTOR/GEARBOX General Guidelines ProcedureFWD Models MWD ModelsSuspension Arm Located on insideTroubleshooting Procedure Using Hydrometer to Check Battery Cells Lead Acid FigureBattery Charger Connector Digital Voltmeter Field Load Test FigureProcedure Troubleshooting Motor Testing FigureNumber of Floating Balls Will Vary According to ChargeOhmmeter Motor Connector ELECTRO-MECHANICAL Parking Brake Testing FigureCap Motor Pin Motor Connector Cap Motor Pin Motor Connector OhmmeterStandard Seat Frame Hardware Torque SpecificationsHardware Torque Specifications Procedure Adjustable Seat FrameCaptains VAN Seat Loctite and Torque to 75 in/lbs Torque to 156 in/lbsWheel Halves Inch WheelsPneumatic with Flat-Free Wheel Halves Torque to Pneumatic Wheel Halves 8 inch Torque to 18 in/lbsPneumatic Wheel Halves Pneumatic with Flat-FreeTorque to 360 in/lbs Torque to 156 in/lbs Torque to 156 in/lbs 1020 in/lbsTorque to 156 in/lbs Torque to 160 in/lbs Loctite This Procedure Includes the Following Arms ProcedureReplacing Captains VAN Seat Armrest Plate Figure Replacing Armrest Pads Captains VAN Seats FigureReplacing Back Upholstery Figure Replacing Seat Positioning Strap Captains VAN Seats FigureH O L S T E R Y Van Seat Frame Seat Positioning StrapΥSPREADER BAR Inches ΥSPREADER BARΥHeight of Spreader Bar from Bottom of Back Canes to Top of Spreader Bar ClampM E Seat Frame Procedure REMOVING/INSTALLING Standard Seat Frame Subassembly FigureReplacing Exact Same Size Standard Seat Frame RemovingSeat Frame Adjustable Seat Frame FigureInches Inch Inch deep InchesChanging Seat Depth Between 12 and 15- Inches Figure A T M ETorque to Brackets, note the Back Angle for reinstallation Changing Seat Width Standard and Adjustable Seat FrameWheelchair to hold the insert in place Mounting Screws Torque to 75-inch poundsSide Spacers Center Seat WidthMounting Screws Component ReplacementCoved Washer Center FrameInstalling Captains Van Seat INSTALLING/REMOVING Captains VAN Seat Assembly FigureRemoving Captains Van Seat Torque to 75-inchAdjustable Frames Remove the captains van seatAssembly. Refer toPerform one 1 of the following sections Perform the instructions outlined in PreparaRemove the seat cushion from the seat pan REMOVING/INSTALLING Seat PAN FigureInstalling Seat Dump Mount Seat Angle AdjustmentInstallation Orientation Replacing Seat Mounting Plates Figure Base Frame ProcedureReplacing Seat Support Brackets Figure S E M EReplacing Seat Support Bracket T-NUTS Figure Procedure Base FrameBattery Charger Connector Mount Replacing Battery Charger Bracket and T-NUTRWD and MWD Models Figure Arrow FWD Model FigureMounting Screw Battery Charger Connector Bracket Base Frame REMOVING/INSTALLING Seat Stop Screws FigureSeat Support Bracket Base Frame Stop Screw Front Seat Stop ScrewBack Frame Procedure REMOVING/INSTALLING CJ Back Brackets FigureC K CJ Bracket mounts Front Holes on Back Angle Detail a PlatesRemove the back assembly from the wheelchair Procedure Back FrameHeavy Duty Models Mine if new back upholstery is neededSteps 6,11 Steps 2Steps 6,17 Steps 4,8Back Angle Adjustment Figure T T E Batteries ProcedureProcedure 9BATTERIES Connecting Battery CablesT T E R I E S Group 24 BatteriesDetail a Battery Box BottomTerminals ends. Refer to Detail a in Figure Group 22 Battery Base Frames FigureRemove battery terminal caps from battery Bottom Tery Cable Rear Jumper Battery Single BatteryFront BoxBattery Discharge Indicator BDI Battery Discharge Indicator BDI in LCD ReadoutDescription and Use of Battery Chargers Charging Batteries FigureRequired Items If one 1 battery is defective INSTALLING/REMOVING Group 24 Battery Boxes FigureRecommended Battery Types Cleaning Battery TerminalsINSTALLING/REMOVING Group 22 Battery BOX Figure This manual REMOVING/INSTALLING the E Wiring Harness FigureProcedure Wiring Harness E S S Recline Angle 4 inches 61o Adjusting Limit Switch FigureReplacing Retainer Bar Retention STRAP/RETAINERReplacing Retainer Clip Perform one 1 the followingSpacer Locknuts Mounting Screws Battery Box Sub-Frame ProcedureSpacer Retainer Retainer ClipReplacing Pneumatic Tires REMOVING/INSTALLING Drive Wheels FigureTubes Drive WHEELS/CASTERS WHEELS/ MotorsREMOVING/INSTALLING Drive Wheel HUB Figure Installing Casters REMOVING/INSTALLING Casters FigureReplacing Forks Figure WHEELS/MOTORSWasher Shock Motor Connector Coupling AllenLocknut Spacer Remove motor with motor lock lever from suspen- sion arm Brake Release Shaft REMOVING/INSTALLING Motor GEARLESS/BRUSHLESSRepositioning Mkiv Joystick VAN Seat Models Figure REMOVING/INSTALLING Mkiv Controller FigureElectronics E C T R O N I C SMounting Screw Shock Arrow Fwd ModelBase Frame Spacer Switch Washers Actuator Overtighten Positioning Limit Switch FigureRecliner C L I N E RGas Cylinder Replacing Recliner Cable Assemblies FigureRod Measures 21/32-inches Mounting Screws and Washers Do not Over-Tighten Gas Cylinder ActuatorReplacing Gas Cylinder REPLACING/ADJUSTING GAS Cylinders FigureChanging Back Height Procedure ReclinerAdjusting Gas Cylinder Seat Pan Removal/Replacement Procedures Recliner ProcedureChanging Seat Depth Figure Changing Seat WidthSpacer Base Frame Seat Mount Plate Inside Suspension Arm AssemblyRemove seat pan on recliner REMOVING/INSTALLING Group 22 Battery BOX Tray Figure REMOVING/INSTALLING GroupBattery BOX SUB-FRAME Figure MWD Wheelchairs ProcedureFront Locknuts Battery Mount Procedure MWD WheelchairsInstalling Group 24 Components Figure Frame Rear LocknutsBattery Box Shock ReplacementGroup 24 Battery Base Frames Figure StepsMounting Screw Spring Washer Shock Battery Box Sub-Frame Retainer Clip Top of ShockBase Frame Mounting Shock Screw Inner Link Spacer Suspension ArmBattery Mount Bracket Base Frame Shock Spring Replacement FigureMounting Screw Suspension Arm Spring Washer Shock LocknutShock Spring Base Replacing Stabilizer Fork Assembly FigureReplacing Stabilizer Wheels Figure MWD Wheelchairsprocedure Adjusting Weight DistributionReplacing Stabilizer Cylinder Spring FigureAdjusting Spring Compression Adjusting Stabilizers FigureHeight Adjustment Replacing Suspension ARM Figure REMOVING/INSTALLING Gearbox Figure16-18 x 1-1/4-inch Mounting Screws 16-18 x 2-1/2-inch Motor Gearbox Suspension ArmBracket End Suspension Arm Inner Link Spacer Mounting Screw Tubular End Suspension ArmSteps 6,10 Shock Replacement REMOVING/INSTALLING Group 22 Battery BOX Tray FigureAnti-Tipper Wheel Replacement Age may resultBattery Tray Procedure RWD WheelchairsRubber ElementRWD Wheelchairs Procedure Shock Replacement FigureSpacer Retainer Clip Or Rubber ElementShock Retainer Bar Spacer TopShock Mounting Screw Suspension Arm Locknut Shock Mounting Screw Suspension ArmBattery BOX or INSTALLING/REMOVING RWD WheelchairsprocedureSpacer Clip is against the battery box retainer This manual Shock Eyelet Assembly Retainer Spring BaseBase Frame Mounting Screw Rubber Element Replacement FigureShock Hex Screw Battery Mount Bracket Adjusting Weight Distribution Figure REMOVING/INSTALLING GearboxAdjustment Options 16-18 2-inch 4-inchAdjusting Weight Distribution Procedure AssemblyRepositioning the MOTOR/ Gearbox Figure Mounting Screws Washer Seat Support Bracket Base FrameInch Rearward Lengthens the wheelbase Repositioning the GEARLESS/BRUSHLESS Motor ,14Standard Position Lengthens the wheel Batterybase Frames in Procedure 9 This manual Brushless Motor in this procedure of theW ManualSecurely tighten adjustment screw Suspension Arm Mounting Washer ScrewsInstructions ANTI-TIPPER Wheel Replacement FigureCharger cable to the suspension arm Anti-Tipper Wheel Spacer LocknutAnti-Tip REMOVING/INSTALLING ANTI-TIP AssemblyLower Washers LocknutsREMOVING/INSTALLING Rear Shroud Figure REMOVING/INSTALLING Front Shroud FigureREMOVING/INSTALLING Side Shroud Assembly Figure FWD Wheelchairs ProcedureFWD Wheelchairs REMOVING/INSTALLING Counterweight FigureHandle Outside LowerEdgeCounterweight Replacing Group 24 Battery BOX SUB-FRAME FigureMounting Bracket Counterweight Bottom Shoulder Screw Bottom Shoulder Screw Bottom Slot in Mounting BracketProcedure FWD Wheelchairs REMOVING/INSTALLING Shocks FigureAdjusting/Installing TIE ROD Replacement FigureIng tie rods Battery wiring harness Detail C Sensor Cable Assembly Replacement FigureRemove the Existing sensor cable assembly Socket Suspension Screw ArmSHORT Motor GearboxTie Wrap C Battery Box Sub Frame Sensor WasherReplacing the Suspension ARM REMOVING/INSTALLING Wiring Harness FigureCurelyTighten ChargerporttothemountingbracketDETAILA.SeTie Wrap B Tie Wrap a14 to 16 inches Inches 17 to 18 inches 19 to 20 inches Adjusting Weight Distribution For New Seat DepthMounting Screws Seat Support Brackets Front Depth Footboard ADJUSTMENTS- DEPTH/HEIGHT/ANGLE FigureAngle HeightFlat Screws Footrest Angle AdjustmentsMounting Positions Hub CapRight FWD Wheelchairs ProcedureHorizontal Position Cam Front Shroud Footrest105 106 Limtied Warranty Limited Warranty
Related manuals
Manual 222 pages 55.68 Kb
Top Page Image Contents