Invacare Torque SP, Arrow Replacing Seat Support Bracket T-NUTS Figure, Procedure Base Frame

Page 34

PROCEDURE 7

BASE FRAME

 

 

WARNING

Do not adjust the position of the seat sup- port bracket in this procedure. If an ad- justment is desired, refer to ADJUSTING

BWEIGHT DISTRIBUTION in PROCEDURE 15 -

AMWD WHEELCHAIRS, PROCEDURE 16 - RWD

SWHEELCHAIRS, or PROCEDURE 17 - FWD

B. Remove adjustable seat frame subassembly. Re-

fer to INSTALLING/REMOVING ADJUSTABLE

SEAT FRAME ASSEMBLY AND OR COMPO-

NENT REPLACEMENT in PROCEDURE 6 of

this manual.

C. Remove captains van seat. Refer toINSTALLING/

REMOVINGCAPTAINSVANSEATASSEMBLYin

E

WHEELCHAIRS of this manual.

PROCEDURE 6 of this manual.

4. Removethetwo(2)mountingscrewsandwashersthat

Fsecure the seat support bracket to the base frame.

R

A

WARNING

M

When installing seat support bracket, en-

sure the mounting screws are threaded

E

into the T-Nuts located inside the channel

 

 

of the base frame.

5. Secure the NEW seat support bracket to base frame with the existing two (2) mounting screws and washers. Torqueto156-inchpounds.

6. Reinstallseatmountplates.RefertoREPLACINGSEAT MOUNTINGPLATESinthisprocedureofthemanual.

7. Adjust seat mount plates to desired angle. Refer to

MOUNTING PLATE - SEAT ANGLE ADJUSTMENT ANDINSTALLATIONORIENTATIONinPROCEDURE 6 of this manual.

8. Reverse STEP 2A, 2B or 2C.

9. Perform the instructions outlined in PREPARATIONS FORREMOVING/INSTALLINGSEATFRAME(STAN- DARD FRAME, ADJUSTABLE FRAME, AND CAP- TAINS VAN SEAT) in PROCEDURE 6 of this manual.

3. Removetheseatmountplates.RefertoREPLACINGSEAT

MOUNTINGPLATESinthisprocedureofthemanual.

NOTE: Before removing seat mounting plates, note the po- sitionofthewashers.

4.Remove the seat support brackets. Refer to REPLAC- INGSEATSUPPORTBRACKETSinthisprocedureof the manual.

5.Remove the seat stop screw that is closest to the end cap. Refer to REMOVING/INSTALLING SEAT STOP SCREWS in this procedure of the manual.

6.Remove the end cap and channel cover.

7.Slide existing T-Nut(s) out of channel.

8.Insert NEW T-Nut(s) into channel in correct orientation.

9.Replace channel cover and end cap.

WARNING

The seat stop screws must be in place be- fore operation of your power wheelchair. Ensure the T-Nut(s) are positioned between both seat stop screws.

10. Use Loctite 242and reinstall seat stop screw into base

frame.

Washer

Mounting Screws

Seat Support

Bracket

11. Reinstall the seat seat support brackets. Refer to RE-

PLACING SEAT SUPPORT BRACKETS in this pro-

cedure of the manual.

Channel Cover

Seat Support

Base

T-Nut

Frame

 

FIGURE 2 - REPLACING SEAT SUPPORT BRACKETS

REPLACING SEAT SUPPORT BRACKET T-NUTS (FIGURE 3)

1.Perform the instructions outlined in PREPARATIONS FORREMOVING/INSTALLINGSEATFRAME(STAN- DARD FRAME, ADJUSTABLE FRAME, AND CAP- TAINS VAN SEAT) in PROCEDURE 6 of this manual.

2.Perform one (1) of the following:

A.Remove standard seat frame subassembly. Refer to REMOVING/INSTALLING STANDARD SEAT FRAME SUBASSEMBLY in PROCEDURE 6 of this manual.

Mounting Screw

Bracket

Washer

 

Channel

 

 

Stop

 

Screw

Base

 

Frame

End Cap

 

 

T-Nut

FIGURE 3 - REPLACING SEAT SUPPORT BRACKET

T-NUTS

34

Page 33 Page 35
Image 34
Page 33 Page 35
Contents Storm Series Wheelchairs I N G E C I a L T E STable of Contents Table of Contents Limited Warranty Specification S SpecificationsSpecifications Arrow FWD has a 400 lb. ratingProcedure General Guidelines Repair or Service InformationGeneral Guidelines Procedure MOTOR/GEARBOXSuspension Arm MWD ModelsFWD Models Located on insideBattery Charger Connector Digital Voltmeter Using Hydrometer to Check Battery Cells Lead Acid FigureTroubleshooting Procedure Field Load Test FigureNumber of Floating Balls Will Vary Motor Testing FigureProcedure Troubleshooting According to ChargeCap Motor Pin Motor Connector ELECTRO-MECHANICAL Parking Brake Testing FigureOhmmeter Motor Connector Cap Motor Pin Motor Connector OhmmeterHardware Torque Specifications Standard Seat FrameCaptains VAN Seat Adjustable Seat FrameHardware Torque Specifications Procedure Loctite and Torque to 75 in/lbs Torque to 156 in/lbsPneumatic with Flat-Free Wheel Halves Torque to Inch WheelsWheel Halves Pneumatic Wheel Halves 8 inch Torque to 18 in/lbsPneumatic with Flat-Free Pneumatic Wheel HalvesTorque to 156 in/lbs Torque to 160 in/lbs Loctite Torque to 156 in/lbs 1020 in/lbsTorque to 360 in/lbs Torque to 156 in/lbs Replacing Captains VAN Seat Armrest Plate Figure Arms ProcedureThis Procedure Includes the Following Replacing Armrest Pads Captains VAN Seats FigureH O L S T E R Y Replacing Seat Positioning Strap Captains VAN Seats FigureReplacing Back Upholstery Figure Van Seat Frame Seat Positioning StrapΥHeight of Spreader Bar from Bottom of Back ΥSPREADER BARΥSPREADER BAR Inches Canes to Top of Spreader Bar ClampM E Replacing Exact Same Size Standard Seat Frame REMOVING/INSTALLING Standard Seat Frame Subassembly FigureSeat Frame Procedure RemovingInches Adjustable Seat Frame FigureSeat Frame Inch Inch deep InchesTorque to A T M EChanging Seat Depth Between 12 and 15- Inches Figure Wheelchair to hold the insert in place Changing Seat Width Standard and Adjustable Seat FrameBrackets, note the Back Angle for reinstallation Mounting Screws Torque to 75-inch poundsSeat Width Side Spacers CenterCoved Washer Component ReplacementMounting Screws Center FrameRemoving Captains Van Seat INSTALLING/REMOVING Captains VAN Seat Assembly FigureInstalling Captains Van Seat Torque to 75-inchPerform one 1 of the following sections Remove the captains van seatAssembly. Refer toAdjustable Frames Perform the instructions outlined in PreparaInstalling REMOVING/INSTALLING Seat PAN FigureRemove the seat cushion from the seat pan Installation Orientation Seat Angle AdjustmentSeat Dump Mount Replacing Seat Support Brackets Figure Base Frame ProcedureReplacing Seat Mounting Plates Figure S E M EProcedure Base Frame Replacing Seat Support Bracket T-NUTS FigureRWD and MWD Models Figure Replacing Battery Charger Bracket and T-NUTBattery Charger Connector Mount Arrow FWD Model FigureSeat Support Bracket Base Frame REMOVING/INSTALLING Seat Stop Screws FigureMounting Screw Battery Charger Connector Bracket Base Frame Stop Screw Front Seat Stop ScrewC K REMOVING/INSTALLING CJ Back Brackets FigureBack Frame Procedure CJ Bracket mounts Front Holes on Back Angle Detail a PlatesHeavy Duty Models Procedure Back FrameRemove the back assembly from the wheelchair Mine if new back upholstery is neededSteps 6,17 Steps 2Steps 6,11 Steps 4,8Back Angle Adjustment Figure Batteries Procedure T T ET T E R I E S Connecting Battery CablesProcedure 9BATTERIES Group 24 BatteriesBattery Box Bottom Detail aRemove battery terminal caps from battery Group 22 Battery Base Frames FigureTerminals ends. Refer to Detail a in Figure Front Single BatteryBottom Tery Cable Rear Jumper Battery BoxDescription and Use of Battery Chargers Battery Discharge Indicator BDI in LCD ReadoutBattery Discharge Indicator BDI Charging Batteries FigureRequired Items Recommended Battery Types INSTALLING/REMOVING Group 24 Battery Boxes FigureIf one 1 battery is defective Cleaning Battery TerminalsINSTALLING/REMOVING Group 22 Battery BOX Figure Procedure Wiring Harness REMOVING/INSTALLING the E Wiring Harness FigureThis manual E S S Adjusting Limit Switch Figure Recline Angle 4 inches 61oReplacing Retainer Clip Retention STRAP/RETAINERReplacing Retainer Bar Perform one 1 the followingSpacer Retainer ProcedureSpacer Locknuts Mounting Screws Battery Box Sub-Frame Retainer ClipTubes Drive WHEELS/CASTERS REMOVING/INSTALLING Drive Wheels FigureReplacing Pneumatic Tires WHEELS/ MotorsREMOVING/INSTALLING Drive Wheel HUB Figure Replacing Forks Figure REMOVING/INSTALLING Casters FigureInstalling Casters WHEELS/MOTORSLocknut Spacer Motor Connector Coupling AllenWasher Shock Remove motor with motor lock lever from suspen- sion arm REMOVING/INSTALLING Motor GEARLESS/BRUSHLESS Brake Release ShaftElectronics REMOVING/INSTALLING Mkiv Controller FigureRepositioning Mkiv Joystick VAN Seat Models Figure E C T R O N I C SBase Frame Spacer Arrow Fwd ModelMounting Screw Shock Recliner Positioning Limit Switch FigureSwitch Washers Actuator Overtighten C L I N E RRod Measures 21/32-inches Mounting Screws and Washers Replacing Recliner Cable Assemblies FigureGas Cylinder Do not Over-Tighten Gas Cylinder ActuatorREPLACING/ADJUSTING GAS Cylinders Figure Replacing Gas CylinderAdjusting Gas Cylinder Procedure ReclinerChanging Back Height Changing Seat Depth Figure Recliner ProcedureSeat Pan Removal/Replacement Procedures Changing Seat WidthRemove seat pan on recliner Plate Inside Suspension Arm AssemblySpacer Base Frame Seat Mount Battery BOX SUB-FRAME Figure REMOVING/INSTALLING GroupREMOVING/INSTALLING Group 22 Battery BOX Tray Figure MWD Wheelchairs ProcedureInstalling Group 24 Components Figure Procedure MWD WheelchairsFront Locknuts Battery Mount Frame Rear LocknutsGroup 24 Battery Base Frames Figure Shock ReplacementBattery Box StepsBase Frame Mounting Shock Screw Shock Battery Box Sub-Frame Retainer Clip Top of ShockMounting Screw Spring Washer Inner Link Spacer Suspension ArmMounting Screw Suspension Arm Spring Washer Shock Spring Replacement FigureBattery Mount Bracket Base Frame Shock LocknutReplacing Stabilizer Wheels Figure Replacing Stabilizer Fork Assembly FigureShock Spring Base Replacing Stabilizer Adjusting Weight DistributionMWD Wheelchairsprocedure Cylinder Spring FigureHeight Adjustment Adjusting Stabilizers FigureAdjusting Spring Compression 16-18 x 1-1/4-inch Mounting Screws 16-18 x 2-1/2-inch REMOVING/INSTALLING Gearbox FigureReplacing Suspension ARM Figure Motor Gearbox Suspension ArmSteps 6,10 Tubular End Suspension ArmBracket End Suspension Arm Inner Link Spacer Mounting Screw Anti-Tipper Wheel Replacement REMOVING/INSTALLING Group 22 Battery BOX Tray FigureShock Replacement Age may resultRubber Procedure RWD WheelchairsBattery Tray ElementSpacer Retainer Clip Shock Replacement FigureRWD Wheelchairs Procedure Or Rubber ElementShock Mounting Screw Suspension Arm Spacer TopShock Retainer Bar Locknut Shock Mounting Screw Suspension ArmSpacer Clip is against the battery box retainer RWD WheelchairsprocedureBattery BOX or INSTALLING/REMOVING This manual Shock Eyelet Assembly Retainer Spring BaseShock Hex Screw Battery Mount Bracket Rubber Element Replacement FigureBase Frame Mounting Screw Adjustment Options REMOVING/INSTALLING GearboxAdjusting Weight Distribution Figure 16-18 2-inch 4-inchRepositioning the MOTOR/ Gearbox Figure AssemblyAdjusting Weight Distribution Procedure Mounting Screws Washer Seat Support Bracket Base FrameStandard Position Lengthens the wheel Repositioning the GEARLESS/BRUSHLESS Motor ,14Inch Rearward Lengthens the wheelbase Securely tighten adjustment screw Brushless Motor in this procedure of theW ManualBatterybase Frames in Procedure 9 This manual Suspension Arm Mounting Washer ScrewsCharger cable to the suspension arm ANTI-TIPPER Wheel Replacement FigureInstructions Anti-Tipper Wheel Spacer LocknutLower REMOVING/INSTALLING ANTI-TIP AssemblyAnti-Tip Washers LocknutsREMOVING/INSTALLING Side Shroud Assembly Figure REMOVING/INSTALLING Front Shroud FigureREMOVING/INSTALLING Rear Shroud Figure FWD Wheelchairs ProcedureREMOVING/INSTALLING Counterweight Figure FWD WheelchairsMounting Bracket Counterweight Bottom Shoulder Screw Replacing Group 24 Battery BOX SUB-FRAME FigureHandle Outside LowerEdgeCounterweight Bottom Shoulder Screw Bottom Slot in Mounting BracketREMOVING/INSTALLING Shocks Figure Procedure FWD WheelchairsTIE ROD Replacement Figure Adjusting/InstallingIng tie rods Remove the Existing sensor cable assembly Sensor Cable Assembly Replacement FigureBattery wiring harness Detail C Socket Suspension Screw ArmSHORT Motor GearboxBattery Box Sub Frame Sensor Washer Tie Wrap CREMOVING/INSTALLING Wiring Harness Figure Replacing the Suspension ARMTie Wrap B ChargerporttothemountingbracketDETAILA.SeCurelyTighten Tie Wrap aMounting Screws Seat Support Brackets Front Adjusting Weight Distribution For New Seat Depth14 to 16 inches Inches 17 to 18 inches 19 to 20 inches Angle Footboard ADJUSTMENTS- DEPTH/HEIGHT/ANGLE FigureDepth HeightMounting Positions Footrest Angle AdjustmentsFlat Screws Hub CapHorizontal Position Cam FWD Wheelchairs ProcedureRight Front Shroud Footrest105 106 Limited Warranty Limtied Warranty
Related manuals
Manual 222 pages 55.68 Kb
Top Page Image Contents