BT 4016 Classic manual Battery level icons, Out of range?, Battery performance

Page 16

Diverse 4016 Classic ~ Issue 2 ~ 6th Edition ~ 1st March ’02 ~ 4416

SETTING UP

Battery level icons

When the batteries are almost flat a beep sounds and the display shows the empty battery icon. You will need to recharge your handset before you can use it. The various states of charge are shown below:

Batteries fully charged

Batteries at 66%

Batteries at 33%

Batteries empty

Out of range?

If you go out of range of a base station for a long time while your handset is switched ON, it may take more than 20 minutes to ‘find’ the base station again when you come back within range. However, by simply switching the handset OFF for a moment, then ON again, it will find the base station within a few seconds.

Battery performance

After charging your handset batteries for the first time, subsequent charging time is approximately 4–5 hours.

Batteries and case may become warm during charging. This is normal.

Under ideal conditions, the handset batteries should give about 10 hours talktime or 200 hours standby time on a single charge. However, new NiCad batteries do not reach their full capacity until they have been in normal use for several days.

Fully discharging the batteries at least once a week will help them last as long as possible. However, the charge capacity of rechargeable batteries will reduce with time as they wear out, so reducing the talk/standby time of the handset. Eventually they will need to be replaced. New batteries can be obtained from any BT shop or from the Diverse Helpline 08457 908070.

If you replace the handset batteries with ones that have been fully charged, the battery indicator will not show full until the next charge cycle has been completed. Charge the handset until the batteries register full again. From then on the display will be correct.

14

Image 16

Contents Diverse 4016 Classic Page At a glance Use lightHandset display BaseHelpline This guideHints and tips boxes DTMF-EARTH Menu structure for directory, redial list, extra directory Menu structure for message handling Commonly used handset functions and settings Quick guideCommonly used answering machine functions and settings Quick guide to handset display icons Unpacking your Diverse 4016 Classic IntroductionFor your records General Safety informationEnvironmental Setting up Plug the power supply unit into the wall socketPlan the location Connect the base stationInsert the batteries If the icons on the display Flash continuouslyBattery performance Battery level iconsOut of range? Setting the date and time To set the time mode 12 or 24-hour clock Please noteUsing the telephone Making and ending callsCall timer Name and number directoryTo receive an external call To store a name and number in the directoryTo dial a number from the directory To edit a directory entryCharacter map Extra directory To delete an entry from the directoryTo delete all entries from the directory To store names and numbers in the Extra directoryRedial To dial a number in the redial listTo copy numbers shown in the redial list to the directory To delete the redial listTo switch secrecy on/off SecrecyPaging and internal calls BackADD Features To switch 3-way conversation function on/offTo transfer an external call between handsets Base SETTo hold a 3-way conversation Alarm clock To set the alarmTo cancel the alarm setting To stop the alarm ringingCalls list Caller Display and other Select ServicesOn 0800 800 To view the Calls list RememberDeleted Store a number from the Calls list into the directoryTo switch Call Waiting on/off During a call when you hear the Call Waiting beepsCall Waiting To accept a waiting callCall Divert Withhold numberTo divert calls To withhold your number from being sentTo switch Ring Back off if set Ring BackHandset settings To adjust the handset ringer volumeTo adjust the handset ringer melody Shortcut buttonTo adjust the earpiece volume To switch autotalk on and offTo reset your handset to the original settings RESET?To switch keyguard on KeyguardBase station settings To adjust the base ringer volumeBase station PIN Personal Identification NumberTo reset your base station to its original settings To adjust the base ringer melodyIt will not reset To switch the answering machine on and off To record your own outgoing messageTo play your outgoing message AnnouncementRight now, please leave a message after the tone RED Phone button Please noteTo delete your outgoing message Call screeningTo use call screening New message indicator Playing messagesTo adjust the message length Additional answering machine settingsTo set the number of rings To switch the base station loudspeaker on or off To adjust the recording qualityQuality Remote access To switch on your answering machine from another phoneTo access your answering machine from another phone To control the answering machine functions during playbackUsing additional handsets and bases Registering additional handsetsPlease note To change the name of a handset To de-register a handsetTo change the internal number of a handset Help NumberCompatibility Approved rechargeable batteriesGuarantee Conditions of this guarantee areWithin the 12-month guarantee period Outside the 12-month guarantee periodSwitchboard compatibility To set the dialling modeTechnical information How many telephones can you have?MS is the standard setting for most UK switchboards To switch temporarily from pulse to tone diallingThis setting is only for the duration of the call To set the recall timeSetting pauses To set a pause before diallingTo set a pause after pressing Recall SavedIndex PIN 0682