BT Diverse 2010 manual ‘Settings confirmation’ tone, Battery warning tone, ‘Range warning’ tone

Page 22

‘Settings confirmation’ tone

You will hear a confirmation tone each time you successfully complete a setting. You can turn this sound on and off. (The standard setting is ON.)

 

DEF

PQRS

1 or 0

STO

3

7

 

 

 

Press the STO button.

Press 3 then 7. Display shows the current setting: 1 = ON, 0 = OFF.

Press 1 to switch the tone ON. Or

Press 0 to switch the tone OFF.

Press the STO button to confirm the new setting.

Battery warning tone

You will hear a tone when the batteries need to be recharged. If the batteries are already fully charged, hearing the signal means they should be replaced. You can turn this sound on and off (the standard setting is ON).

 

DEF

ABC

1 or 0

STO

3

2

 

 

 

Press the STO button.

Press 3 then 2. Display shows the current setting: 1 = ON, 0 = OFF.

Press 1 to switch the tone ON. Or

Press 0 to switch the tone OFF.

Press the STO button to confirm the new setting.

‘Range warning’ tone

If you are on a call as you reach the limit of your handset’s range, you will hear a tone to warn you that you will lose the call if you move further away. You can turn this sound on and off (the standard setting is OFF).

 

DEF

DEF

1 or 0

STO

3

3

 

 

 

Press the STO button.

Press 3 then 3 again. Display shows the current setting: 1 = ON, 0 = OFF.

Press 1 to switch the tone ON.

Or

Press 0 to switch the tone OFF.

Press the STO button to confirm the new setting.

‘In-range’ tone

If you have taken the handset outside the phone’s range – provided the handset is switched on – you will hear a tone when you come back within range. You can turn this sound on and off. (The standard setting is OFF.)

 

DEF

JKL

1 or 0

STO

3

5

 

 

 

Press the STO button.

Press 3 then 5. Display shows the current setting: 1 = ON, 0 = OFF.

Press 1 to switch the tone ON. Or

Press 0 to switch the tone OFF.

Press the STO button to confirm the new setting.

19

Image 22
Contents Diverse For your records Base Station PIN Number Handset PIN NumberAt a glance INTDiverse Base station underside view Power cord Telephone Line cord This guide Hints and tips boxesIntroducing the Diverse Building up a phone systemGeneral cleaning Setting upFollow these steps to get your Diverse 2010 ready for use Connect the power cable Install the rechargeable batteries in the handset Fit the handset Belt clipBattery low warning Battery display when inserting or replacing a batteryBattery performance Getting the most out of your batteriesIf the symbol flashes To switch to Protected when Handset is on Using your DiverseOn/Off and Protected modes To end a call Call timerTo make an external call To receive an external callTo receive an internal call To page a handset from the base stationTo make an internal intercom call to Another handset To make an internal call to all HandsetsTo transfer an external call between Handsets Quick call transferTo speed dial a number stored on Memory To store a numberTo clear all the numbers stored on a Handset’s memory Additional features Setting to Tone or Pulse diallingSecurity code and handset PIN To change a system code for Diverse 2010 base stationAdjusting the ear piece volume Adjusting volumes and tonesTo adjust the ringer volume Handset To adjust the tone of the handset‘Confirmation’ tones To adjust the ringer volume Base stationTo adjust the tone of the base station Ringer ‘Wrong key’ tone‘Range warning’ tone ‘Settings confirmation’ toneBattery warning tone ‘In-range’ toneTo reset your Diverse 2010 handset to the original settings Secrecy Call allocationTo set the number of rings on ring Priority To set which handset will receive ring PriorityTo add and remove handsets that Respond to group ringing Call barring To cancel your own ‘special numbers’To store your own ‘special numbers’ Entering access codes Using your Diverse 2010 with a switchboardTo insert an access code Setting the access pause At the base station To register a handsetPlease Note To remove a handset registered at Base stationHow to set up multiple base stations and handsets Operating with additional base stationsTo set/clear the base station number Display from a handset To set your handset for automatic base selectionSTO INT Within the warranty period MaintenanceService Outside the warranty periodEmergency calls HelpReplacing handset batteries When connected to a switchboard Environment If the power failsTechnical information ApprovalTechnical specification Index RENOffices in Europe, North America, Japan and Asia Pacific 504116