BT Diverse 2010 manual When connected to a switchboard

Page 36

Recommended batteries should have a power rating of 600m Ah 1.2V. Batteries are available from the Diverse Helpline 0345 908070 and your local BT shop.

BT accepts no responsibility for damage caused to your Diverse 2010 handset by the use of non-approved batteries.

No display appears

Is the handset switched on? The battery may be flat or dead. Recharge or replace the battery.

No dial tone

Is the telephone line cord plugged into the phone socket and the base station?

If other handsets are registered on the base, the outside line may already be in use. Wait until the call is finished and try again.

The symbol is flashing or you cannot link up with the base station

Is the handset registered with the base station? To register the handset, see page 26. Is the power cable connected at the base and the power switched on at the wall socket?

If you press the PHONE button whilst is flashing, you will hear four short

beeps from the handset.

Please note:

If you go out of range of a base station for a long time while your handset is switched ON, it may take more than 20 minutes to ÔfindÕ the base station again when you come back within range. However, by simply switching the handset OFF for a moment, and then ON again, it will find the base station within a few seconds.

The base station or handset does

not ring

The ringer volume may be set too low, or switched off at the base station. To adjust the ringer volume at the handset or base station, see pages 17 or 18 respectively.

Is the telephone line cord connected correctly? See page 6.

Can’t get through, even though a

dialling tone can be heard

You may be set to the wrong signalling method. To change between TONE and PULSE dialling, see ‘Additional features’, page 15.

When connected to a switchboard

You can’t get a connection or you get

the wrong connection after speed

dialling

Have you entered a pause after the access code? See page 24.

Check you have selected the correct dialling mode. See page 15.

Handset beeps

Are the handset batteries low? You will hear a beep every 30 seconds.

If is flashing?

You will hear four short beeps when you press the PHONE button. Check you are still in range of your base station.

Buzzing noise on my

Radio/TV/Answering Machine/PC

Diverse is too close and is causing interference. Move it further away.

If you are still experiencing difficulty, please call the Diverse Helpline on

0345 908070.

33

Image 36
Contents Diverse For your records Base Station PIN Number Handset PIN NumberAt a glance INTDiverse Base station underside view Power cord Telephone Line cord This guide Hints and tips boxesIntroducing the Diverse Building up a phone systemSetting up General cleaningFollow these steps to get your Diverse 2010 ready for use Connect the power cable Install the rechargeable batteries in the handset Fit the handset Belt clipBattery display when inserting or replacing a battery Battery performanceBattery low warning Getting the most out of your batteriesIf the symbol flashes Using your Diverse To switch to Protected when Handset is onOn/Off and Protected modes Call timer To make an external callTo end a call To receive an external callTo page a handset from the base station To make an internal intercom call to Another handsetTo receive an internal call To make an internal call to all HandsetsTo transfer an external call between Handsets Quick call transferTo store a number To speed dial a number stored on MemoryTo clear all the numbers stored on a Handset’s memory Additional features Setting to Tone or Pulse diallingSecurity code and handset PIN To change a system code for Diverse 2010 base stationAdjusting volumes and tones To adjust the ringer volume HandsetAdjusting the ear piece volume To adjust the tone of the handsetTo adjust the ringer volume Base station To adjust the tone of the base station Ringer‘Confirmation’ tones ‘Wrong key’ tone‘Settings confirmation’ tone Battery warning tone‘Range warning’ tone ‘In-range’ toneTo reset your Diverse 2010 handset to the original settings Secrecy Call allocationTo set which handset will receive ring Priority To set the number of rings on ring PriorityTo add and remove handsets that Respond to group ringing To cancel your own ‘special numbers’ Call barringTo store your own ‘special numbers’ Using your Diverse 2010 with a switchboard Entering access codesTo insert an access code Setting the access pause At the base station To register a handsetPlease Note To remove a handset registered at Base stationHow to set up multiple base stations and handsets Operating with additional base stationsTo set/clear the base station number Display from a handset To set your handset for automatic base selectionSTO INT Maintenance ServiceWithin the warranty period Outside the warranty periodHelp Emergency callsReplacing handset batteries When connected to a switchboard If the power fails Technical informationEnvironment ApprovalTechnical specification Index RENOffices in Europe, North America, Japan and Asia Pacific 504116