BT Diverse 2010 manual Technical specification

Page 38

Technical specification

Standard	DECT, GAP

Number of channels	120 duplex channels

Radio frequency range	1880 MHz to 1900 MHz

Duplex method	Time-division multiplexing. 10 ms frame length

Channel grid	1728 kHz

Bit rate	1152 kbit/s

Modulation	GFSK

Voice coding	32 kbit/s

Transmitted power	10 mW, average output per channel

Range (in ideal conditions)	UP TO 300 METERS OUTDOORS
	UP TO 50 METERS IN BUILDINGS

Power supply	Base station 220/230 V –/ 50 Hz (AC adaptor)

Power consumption base station	Standby: approx. 3 W
	Call mode: approx. 5 W

Operating time, mobile station	Standby: up to 40 hours
(with fully charged battery)	Phone in use: Up to 7 hours

Permitted ambient conditions	+5˚C to 45˚C
for operation (maximum)	20% to 75% rel. humidity

Permitted storage temperature	–10˚C to +60˚C

Signaling method	Dial pulsing/DTMF

Signal key function	Earth Recall/Timed Break Recall

Base station dimensions (mm)	Approx. 146 x 117 x 70 (L x W x H)

Handset dimensions (mm)	Approx. 160 x 55 x 25 (L x W x H)

Weight	Base station: 210g
	Mobile station: 165g

Charging time in base station	Approx. 5 hours

Cable lengths	Telephone line approx. 3m
	Power cable approx. 3m

Connecting plug	BT-plug TSV 6/4 (telephone line cord)
	TSV 6/4 (power cable)
	BT-plug (power adaptor)

35

Image 38

Contents Diverse For your records Base Station PIN Number Handset PIN NumberAt a glance INTDiverse Base station underside view Power cord Telephone Line cord This guide Hints and tips boxesIntroducing the Diverse Building up a phone systemFollow these steps to get your Diverse 2010 ready for use Setting upGeneral cleaning Connect the power cable Install the rechargeable batteries in the handset Fit the handset Belt clipBattery low warning Battery display when inserting or replacing a batteryBattery performance Getting the most out of your batteriesIf the symbol flashes On/Off and Protected modes Using your DiverseTo switch to Protected when Handset is on To end a call Call timerTo make an external call To receive an external callTo receive an internal call To page a handset from the base stationTo make an internal intercom call to Another handset To make an internal call to all HandsetsTo transfer an external call between Handsets Quick call transferTo clear all the numbers stored on a Handset’s memory To store a numberTo speed dial a number stored on Memory Additional features Setting to Tone or Pulse diallingSecurity code and handset PIN To change a system code for Diverse 2010 base stationAdjusting the ear piece volume Adjusting volumes and tonesTo adjust the ringer volume Handset To adjust the tone of the handset‘Confirmation’ tones To adjust the ringer volume Base stationTo adjust the tone of the base station Ringer ‘Wrong key’ tone‘Range warning’ tone ‘Settings confirmation’ toneBattery warning tone ‘In-range’ toneTo reset your Diverse 2010 handset to the original settings Secrecy Call allocationTo add and remove handsets that Respond to group ringing To set which handset will receive ring PriorityTo set the number of rings on ring Priority To store your own ‘special numbers’ To cancel your own ‘special numbers’Call barring To insert an access code Using your Diverse 2010 with a switchboardEntering access codes Setting the access pause At the base station To register a handsetPlease Note To remove a handset registered at Base stationHow to set up multiple base stations and handsets Operating with additional base stationsTo set/clear the base station number Display from a handset To set your handset for automatic base selectionSTO INT Within the warranty period MaintenanceService Outside the warranty periodReplacing handset batteries HelpEmergency calls When connected to a switchboard Environment If the power failsTechnical information ApprovalTechnical specification Index RENOffices in Europe, North America, Japan and Asia Pacific 504116