BT Diverse 2010 manual Sto Int

Page 33

The handset must be switched ON.

STO INT 0

•Press the STO button.

•Press the INT button. Display shows the numbers of the base stations at which the handset is registered.

•Press the 0 button to set automatic selection.

•Press the STO button to confirm. The handset will now select the base offering the strongest signal. Display can show the base station selected (see previous section ‘To set/clear the base station number display’).

If you are in an area where base station signals overlap it is best to specify the base/ telephone line you operate through. In this case you change automatic base selection to manual selection (with an automatic search default), see opposite.

To set your handset for manual base

selection (with an automatic search

default)

This setting tells your handset to search for a specific base signal for 30 seconds. If the signal can not be found, the handset reverts to automatic selection of the base with the best signal. This setting is recommended where there is an overlap between two or three base stations.

The handset must be switched ON.

	INT	1	GHI
STO			4

•Press the STO button.

•Press the INT button. Display shows the numbers of the base stations at which the handset is registered.

•Press the number of the base (from 1 to 4) through which you wish to make calls.

•Press the same number again. This tells the handset to revert to automatic search if the chosen base is unavailable.

•Press STO to confirm.

If you do not wish to allow the handset to revert to automatic signal selection press the base station number just once. This will mean that the handset can only operate through the base you select.

If you move out of range from one base station and into the range of another during a call, you will lose your connection.

If your handset is taken out of range, switch it off, move back into base station range, and then switch on again. This will speed up re-registration to the base signal.

30

Image 33

Contents Diverse Base Station PIN Number Handset PIN Number For your recordsINT At a glanceDiverse Base station underside view Power cord Telephone Line cord Hints and tips boxes This guideBuilding up a phone system Introducing the DiverseSetting up General cleaningFollow these steps to get your Diverse 2010 ready for use Connect the power cable Fit the handset Belt clip Install the rechargeable batteries in the handsetBattery performance Battery display when inserting or replacing a batteryBattery low warning Getting the most out of your batteriesIf the symbol flashes Using your Diverse To switch to Protected when Handset is onOn/Off and Protected modes To make an external call Call timerTo end a call To receive an external callTo make an internal intercom call to Another handset To page a handset from the base stationTo receive an internal call To make an internal call to all HandsetsQuick call transfer To transfer an external call between HandsetsTo store a number To speed dial a number stored on MemoryTo clear all the numbers stored on a Handset’s memory Setting to Tone or Pulse dialling Additional featuresTo change a system code for Diverse 2010 base station Security code and handset PINTo adjust the ringer volume Handset Adjusting volumes and tonesAdjusting the ear piece volume To adjust the tone of the handsetTo adjust the tone of the base station Ringer To adjust the ringer volume Base station‘Confirmation’ tones ‘Wrong key’ toneBattery warning tone ‘Settings confirmation’ tone‘Range warning’ tone ‘In-range’ toneTo reset your Diverse 2010 handset to the original settings Call allocation SecrecyTo set which handset will receive ring Priority To set the number of rings on ring PriorityTo add and remove handsets that Respond to group ringing To cancel your own ‘special numbers’ Call barringTo store your own ‘special numbers’ Using your Diverse 2010 with a switchboard Entering access codesTo insert an access code Setting the access pause To register a handset At the base stationTo remove a handset registered at Base station Please NoteOperating with additional base stations How to set up multiple base stations and handsetsTo set your handset for automatic base selection To set/clear the base station number Display from a handsetSTO INT Service MaintenanceWithin the warranty period Outside the warranty periodHelp Emergency callsReplacing handset batteries When connected to a switchboard Technical information If the power failsEnvironment ApprovalTechnical specification REN Index504116 Offices in Europe, North America, Japan and Asia Pacific