VTech CS5121-3, CS5121-2, CS5122-3, CS5121-4 Important safety instructions

Page 50
47 Appendix

Important safety instructions

When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1.Read and understand all instructions.

2.Follow all warnings and instructions marked on the product.

3.Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

4.Do not use this product near water (for example, near a bathtub, kitchen sink, or swimming pool).

5.Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

6.Slots and openings in the back or bottom of the telephone base and handset are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. This product should not be placed in any area where proper ventilation is not provided.

7.This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company.

8.Do not allow anything to rest on the power cord. Do not install this product where the cord may be walked on.

9.Never push objects of any kind into this product through the slots in the telephone base or handset because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product.

10.To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the telephone base or handset other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

11.Do not overload wall outlets and extension cords.

12.Unplug this product from the wall outlet and refer servicing to an authorized service facility under the following conditions:

A.When the power supply cord or plug is damaged or frayed.

B.If liquid has been spilled onto the product.

C.If the product has been exposed to rain or water.

D.If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operation instructions. Improper adjustment of other controls may result in damage and often requires extensive work by an authorized technician to restore the product to normal operation.

E.If the product has been dropped and the telephone base and/or handset has been damaged.

F.If the product exhibits a distinct change in performance.

13.Avoid using a telephone (other than cordless) during an electrical storm. There is a remote risk of electric shock from lightning.

14.Do not use the telephone to report a gas leak in the vicinity of the leak.

15.Only put the handset of your telephone next to your ear when it is in normal talk mode.

16.The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling or an under-the-table/cabinet outlet.

SAVE THESE INSTRUCTIONS

www.vtechphones.com

Image 50
Contents Important safety instructions CongratulationsTable of contents Appendix Parts checklist Getting startedTelephone base and chargers installation Battery installation and charging Mounting bracket installation Wall mounting bracket installationDesktop/tabletop bracket installation Handset layout VOL-/CIDTelephone base layout DeleteTelephone settings Date and timeRinger volume handset RingerDial mode Home area codeLanguage Telephone operation Call waiting Temporary tone dialingRedial Find handsetTransfer an external call Directory Store a directory entryCharacter chart Review the directoryEdit a directory entry DirectoryDelete a directory entry Copy a directory entry into speed dial Dial a number from the directorySpeed dial Store a speed dial entryEdit a speed dial entry Delete a speed dial entry Dial a speed dial numberReassign speed dial locations About caller ID Call log Review the call log Make call log entries ready to dialDial a call log number Save a call log entry to the directory Entries ready to dial section onDelete from the call log Delete an entryCall log display screen messages Displays WhenAnswering system Message capacityActivate the answering system Set the clockAnswering system setup Set number of ringsSet remote access code Set telephone base ringerSet message alert tone Outgoing announcement Play your announcementRecord your own announcement Delete your announcementOptions during playback New message indicationMessage playback Record a memo Delete all messagesRecord and play memos Memo playbackCall screening Call interceptMessage window displays Window displays WhenRemote access Command FunctionHandset display screen messages Appendix Battery Important safety instructions Troubleshooting Problem SuggestionAppendix Connecting To take place Your area. See Dial mode on page 10 to set the dial type Telephone company charges may apply Remove and re-insert the battery System does Troubleshooting Troubleshooting Maintenance Operating rangeWarranty About cordless telephonesHow do you get warranty service? FCC, Acta and IC regulations FCC PartRbrc seal Technical specifications Index Transfer an external call  91-002141-010-100 User’s manual