Panasonic KX-TG6562E, KX-TG6561E Error messages, Display message Cause/solution

Page 44

TG6561E(e).book Page 44 Tuesday, July 13, 2010 1:50 PM

Useful Information

Error messages

If the unit detects a problem, one of the following messages is shown on the display.

Display message	Cause/solution
Base no power	L The handset has lost communication with the base
or	unit. Move closer to the base unit and try again.
No link.	L Unplug the base unit’s AC adaptor to reset the unit.
Reconnect AC	Reconnect the adaptor and try again.
adaptor.	L The handset’s registration may have been cancelled.
	Re-register the handset (page 29).
Check Phone Line	L The supplied telephone line cord has not been
	connected yet or not connected properly. Check the
	connections (page 10).
Error	L Recording was too short. Try again.
Failed	L Phonebook copy failed (page 21). Confirm the other
	handset (the receiver) is in standby mode and try
	again.
Incomplete	L The receiver’s phonebook memory is full. Erase the
	unwanted phonebook entries from the other handset
	(the receiver) and try again.
Memory Full	L The phonebook memory is full. Erase unwanted
	entries (page 20).
	L Message memory is full. Erase unwanted messages
	(page 35).
	L The call barred list memory is full. Erase unwanted
	entries (page 29).
Use rechargeable	L A wrong type of battery such as Alkaline or
battery.	Manganese was inserted. Use only the rechargeable
	Ni-MH batteries noted on page 4, 7.
You must first	L You must subscribe to a Caller ID service. Once you
subscribe to	receive caller information after subscribing to a Caller
Caller ID.	ID service, this message will not be displayed.

44Helpline Tel. No.: U.K. 0844 844 3898 R.O.I. 01289 8333

Image 44

Contents Before initial use, see Getting Started on Caller ID Service Voice Mail ServiceIntroduction Important InformationAccessory information Supplied accessoriesAccessory item/Part number Quantity KX-TG6561 KX-TG6562 Model compositionSales and support information Additional/replacement accessoriesExpanding your phone system Declaration of Conformity General informationFor your future reference For your safety Important safety instructions Other information TG6561Ee.book Page 9 Tuesday, July 13, 2010 150 PM Setting up Battery installationBattery charge ConnectionsOperation Operating time During a power failureBattery level Icon Base unit ControlsHandset Soft key icons Icon Action DisplayHandset display items Meaning Turning the power on/off Initial settingsDisplay language Date and timeOne touch eco mode Wall mountingUsing the handset Using the base unit Service usersMaking calls Pause for PBX/long distanceUseful features during a call Using the handsetAnswering calls HoldCall share MuteRecall/flash Handset key lock Handset phonebook Copying all entries Copying phonebook entriesCopying an entry Making a call using the speed dial keys Base unit speed dialAdding phone numbers to speed dial To erase a stored phone numberMain menu Sub-menu Programmable settingsProgramming by scrolling through the display menus Display Setup Programming using the direct commands Feature Code SettingFor the answering system Feature Code Setting Answer OffTG6561Ee.book Page 27 Tuesday, July 13, 2010 150 PM Alarm Special programmingChanging the handset name Incoming call barring Caller ID subscribers onlyChanging the base unit PIN Personal Identification Number Deregistering a handset Setting the repeater modeIncreasing the range of the base unit Using Caller ID service Caller ID featuresCaller list Viewing the caller list and calling backEditing a caller’s phone number before calling back Erasing selected caller informationErasing all caller information Storing caller information to the phonebookAnswering system Turning the answering system on/offMemory capacity including your greeting message Call screeningListening to messages using the base unit Using a pre-recorded greeting messageGreeting message Recording your greeting messageListening to messages using the handset Operating the answering system during playbackErasing all messages Operating the answering systemRemote access code Using the answering system remotelyRemote operation Calling back Caller ID subscribers onlyAnswering system settings Remote commandsTurning on the answering system remotely Number of rings before the unit answers a callCaller’s recording time Selecting Greeting OnlyVoice mail service Intercom Handset locatorTransferring calls, conference calls Making an intercom callTo complete the transfer Press ic To establish a conference call Press wTo complete the transfer Press s To establish a conference call PressCharacter entry modes When the unit displays the character entry screenCharacter entry Extended 1 character table N Extended 2 character table OError messages Display message Cause/solutionProblem Cause/solution TroubleshootingGeneral use Problem Cause/solution Battery recharge Problem Cause/solution Making/answering calls, intercomCaller ID Problem Cause/solution Answering system Problem Cause/solution Own greeting message againLiquid damage Problem Cause/solution Conditions of guarantee Panasonic Business Systems U.KIndex Sales Department Copyright