Panasonic KX-TG2361JX operating instructions General, Problem Cause & Remedy, Recharge battery is

Page 77

		Troubleshooting

	Problem	Cause & Remedy

	When you play back messages	• The date and time may be set incorrectly.
	or turn on the Answering	Set the date and time again (p. 14).
	System, the handset and/or
	base unit announces the wrong
	day and time.
	General

	Problem	Cause & Remedy

	The handset and/or base unit	• Check the settings (p. 9–11).
	does not work.	• Check whether the dialing mode setting is
		correct (p. 15).
		• Fully charge the battery (p. 10).
		• Clean the charge contacts and charge again
		(p. 11).
		• Check battery installation (p. 10).
		• Unplug the base unit’s AC adaptor to reset
		it. Plug in, and try again.
		• Re-install the battery (p. 10) and fully charge
		it.

	Time setting is erased, and “E”	• If a power failure occurs, time setting may
	flashes on the base unit	be erased. Set the date and time again
	display or “E Press MENU.”	(p. 14).
	flashes on the handset display.

	“Recharge battery” is	• Fully charge the battery (p. 10).
	displayed, “7” flashes, or
	the handset beeps
	intermittently.

	“Charge for 6h” and “8”	• The battery has been discharged. Fully
	are displayed and the handset	charge the battery (p. 10).
	does not work.	• Check battery installation (p. 10).

	You charged the battery fully,	• Clean the charge contacts and charge again
	but “Recharge battery” is	(p. 11).
	still displayed and/or “7”	• The battery may need to be replaced. If you
	continues to flash, or “Charge	install a new battery, fully charge it (p. 10).
	for 6h” and “8” are
	displayed.

	The CHARGE indicator does	• This is normal.
	not go out after the battery has
	been charged.

Useful Information

77

Image 77

Contents Pulse-or-tone dialing capability Charge the battery for 6 hours before initial useDual Handsets Digital Cordless Answering System For your future reference Accessories includedBase Unit Location/Noise Battery ChargeFor Best Performance Contents Contents Base unit Location of ControlsAnswer on Button Message Button p Greeting REC RecordHandset Location of ControlsCharger unit OFF ButtonHandset navigator key Handset soft keysBase unit display Talk 00-00-32 KVE MuteLConnections InstallationBattery strength Installation Installing the Battery in the HandsetTo replace the battery Display prompt Battery strengthBattery information InstallationBattery replacement RechargeHow to select a function item from the menu Programmable SettingsInitial setting Then press Save to save your settingMain menu Programmable Settings Function Menu Table HandsetTo confirm the date and time, repeat steps 1 and 2 above Programmable Settings Date and Time HandsetProgrammable Settings Dialing Mode Handset Auto Talk Handset Programmable Settings Line Mode HandsetRinger setting Programmable Settings Ringer VolumeHandset ringer volume Handset Base unit ringer volume Base Unit Programmable SettingsTo turn the ringer on, press Volume or Ringer ToneSelect the desired ringer tone by pressing d or B Setting the base unit ringer tone by using the HandsetRinger tone 1Tone KBack dB SaveL To 3 Bell ringer patterns To 7 Melody patternsPreparing the Answering System Programmable Settings LCD Contrast HandsetGreeting Message Base Unit Scroll to LCD contrast by pressing d orTo record a greeting message Preparing the Answering SystemTo review the greeting To erase the greetingCaller’s Recording Time Handset Flash Memory Message Backup Message storagePre-recorded greeting Recording timeSelect the number of rings by pressing d or Number of Rings HandsetToll saver Number of ringsRecording mode Preparing the Answering System Recording Mode HandsetScroll to Recording mode by pressing d Select the recording mode by pressing d orMaking Calls Using the Handset HandsetTo have a hands-free phone conversation Hands-free Digital Duplex SpeakerphoneMaking Calls To redial using the redial list Memory RedialTo dial after confirming the entered number To redial the last number dialedBacklit LCD display/Lighted handset keypad To put a call on holdVoice Enhancer Technology To adjust the speaker volume during a conversation Making Calls Using the Base Unit Base UnitPress SP-PHONE Dial a phone numberTalk into the MIC To hang up, press SP-PHONE Answering CallsOFF s Auto Talk To transfer the call to another person, see pagesHow Caller ID information is displayed Caller ID ServicePrivate name display Display MeaningAnnouncing caller information Talker Caller ID Caller ID Service Using Talking Caller IDHandset Talking Caller ID feature Handset Caller ID ServiceBase unit Talking Caller ID feature Handset To turn Talking Caller ID on or offPress Rcvd calls, d, or B to enter the Caller List Using the Caller ListViewing the Caller List Handset Calling Back from the Caller List Handset Using the Caller ListWhat , means If a caller calls more than oncePress Select Press Edit Scroll to the desired caller by pressing d or15553215555 15553215555 Kf MENU=Save PL 015553215555Caller List Press Rcvd calls, d, or B to enterScroll to the desired caller by pressing d or Press SelectTo erase a specific caller Using the Caller List Erasing Caller Information HandsetTo erase all entries Then press EraseTo store an emergency number Phone BookStoring Names and Numbers Handset Phone Book If you make a mistake when entering a name or numberSelecting characters to enter names For example, to enter TomPress Search Phone Book Dialing from the Phone Book HandsetTo search for a name by initial Press d repeatedly until the desired name is displayedIndex table Chain Dial HandsetWhile you are on a call Press Menu Search for the desired item by pressing d orJane Walker Phone Book Editing an Item in the Phone Book HandsetErasing an Item in the Phone Book Handset To copy one phone book item to another handset Phone Book Copying Items in the Phone Book HandsetPress Menu Scroll to Copy phone book by pressing d Press Select at Copy 1 itemCopy phone book Phone BookCopy all items Scroll to Copy all items by pressing dMaking Intercom Calls IntercomPress HOLD/INTERCOM Press LOCATOR/INTERCOMAnswering Intercom Calls IntercomDuring an intercom call Press C, s or HOLD/INTERCOMTo make a voice announcement to all handsets, press 3 When stop paging, press SP-PHONE or LOCATOR/INTERCOMIntercom Voice Paging Base Unit Press SP-PHONE or LOCATOR/INTERCOM to answer Transferring a CallQuick call transfer Transferring a CallFrom a Handset to another Handset To join a conversation Call Share Conference CallsDuring a call, press HOLD/ Intercom To page the base unit, pressFor Call Waiting Service Users Special FeaturesTemporary Tone Dialing Muting Your ConversationSelecting the flash time Handset Special Features Using the Pause KeySet flash time Scroll to Set flash time by pressing dHandset incoming call tone Handset Special Features Incoming Call Tone Handset Base UnitBase unit incoming call tone Handset Incoming callTo turn the Dial Lock on Special Features Key Tone HandsetDial Lock Handset Dial lock Special FeaturesTo cancel the Dial Lock Handset 1 Registered Handset RegisteringAutomatic Answering Operation Setting the Unit to Answer Calls Base UnitPress Answer on to turn on the Answering System Press Answer ON, Greeting REC, orTo turn the incoming call monitoring feature off Press Message Listening to MessagesTo play back messages Voice menu Press Menu Press Select at Message playTo end remote operation, press OFF Listening to Messages For Caller ID service users pTo call back the displayed number 5557778888 KRepeat SkipL KEdit CallLErasing a specific message Erasing MessagesErasing all messages Within 10 seconds, press Erase againRecording a Memo Message When finished, press Memo or StopRemote Code Handset Remote Operation from a Touch Tone PhoneSummary of remote operation Enter a 2-digit remote codeTalk after the long beep Remote Operation from a Touch Tone Phone Voice MenuSkipping the greeting Direct commandsTo turn on the Answering System Belt Clip Connecting the optional headsetOptional Headset To attach the belt clip To remove the belt clipWall Template Wall MountingWall Template for the Charger unit Wall MountingMenu item Command Selection items Direct CommandsDuring programming Direct CommandsDisplay message Cause & Remedy If the Following Appears on Your DisplayIf the Following Appears on Your Display Telephone System TroubleshootingProblem Cause & Remedy Troubleshooting Answering System TroubleshootingRecharge battery is Problem Cause & RemedyBut Recharge battery is GeneralSafety Instructions Safety Instructions SpecificationsPQQX14264ZA F0504-0D 62, 4-chome, Minoshima, Hakata-ku, Fukuoka 812-8531, Japan