Sennheiser 2015 HDX noise reduction system, RF link Inherent Noise of the RF link Transmitter

Page 47

HDX noise reduction system

RF link

Inherent

noise of the RF link

Transmitter

Receiver

You can hear the difference:

This product is equipped with HDX, the Sennheiser noise reduction system that reduces RF interference. It increases the signal-to-noise ratio in wireless audio transmission. HDX is a wideband compander system which compresses the audio signal in the transmitter in a 2:1 ratio (related to dB) to lift it above the inher- ent noise floor of the RF link. A 110 dB dynamic range signal is thus transmitted with an effective dynamic range of only 55 dB, which is above the 60 dB noise floor of the RF link. In the receiver the signal is expanded in an identical and opposite way in a 1:2 ratio to restore the original signal, at the same time reducing the RF noise to below the noise floor of the receiver.

HDX has been specially developed for high quality RF microphone systems.

Note:

Only transmitters and receivers that are equipped with HDX can work correctly with each other. If non HDX equipment was mixed with HDX, the dynamic range would be drastically reduced and the trans- mission would sound blunt and flat. HDX is permanently active and cannot be switched off.

99

Image 47
Contents Mikroport System 209 Bedienungsanleitung105 157Mikroport System Safety instructions Contents 102 Warranty regulationsOperating principle of the 2015 Mikroport System 2015 Mikroport System2015 EZB Transport case Transport holding device EZG Delivery includesMKE Operating controls of the EK 2015 receiver Alphanumeric display Battery status indicationAudio signal indication Indications and displays on the receiverDisplay for the RF level Display for lock modeDisplay for the audio level Display for microphone level internal microphoneOperating controls of the SK 2015 transmitter Audio peak indication Red LED flashing Battery pack or the batteriesIndications and displays on the transmitter Mute indicationDisplay for microphone level Display for line levelTransport case Transport holding device Preparing the units for useTransporting the transmitter and receiver Connecting the microphones to the transmitter Connecting sound sources to the transmitterHow to properly use the battery pack or the batteries MKE ME 2015-H Attaching and positioning the microphonesConnecting the headphones Connecting the receiver to hearing aids or headphonesConnecting audio sources to the transmitter Wearing the transmitter or receiver around your neck Attaching the transmitter or receiver to clothingActivating/deactivating the lock mode Using the receiverSwitching the receiver on/off Switching the channel Adjusting the level of the received audio signalAdjusting the level of the internal microphone Displaying the frequency MIC Operating menu of the EK 2015 receiverMuting the microphone Using the transmitterSwitching the transmitter on/off Activating/deactivating the lock mode Function of the buttons Working with the transmitter’s operating menuPress the / rocker button UP/DOWN to select a menu Adjusting a settingGetting into the operating menu Selecting a menuExiting the operating menu Storing a settingOverview of menus Operating menu Operating menu of the SK 2015 transmitterAdjusting the sensitivity of the line input Adjustment tips for the operating menu of the transmitterAdjusting the microphone sensitivity Tion-free Switching between the channelsNel that is released on all receivers Error checklist TroubleshootingFor system planning For the MKE 2015-0 plug-on microphone optional accessoryFor the ME 2015-H headset microphone optional accessory Recommendations and tipsFor multi-channel operation Care and maintenanceFor optimum reception Working with the configuration menu Configuration of the units by the technical expertGetting into the configuration menu Exiting the configuration menu Reset Structure of the configuration menu of the EK 2015 receiverAccess Reset Receiver only Adjustment tips for the configuration menuSwitching the internal microphone on or off receiver only Adjusting the squelch threshold receiver onlyReleasing channels for the user Mitter and receiver Press the SET button and the button UP simultaneouslyThen displays the next channel that can be released PlayEntering a name Resetting the unit to the factory-preset default settingsChanging the face plate receiver only Colored battery doors and face platesChanging the battery compartment cover Close the battery compartmentRange C Additional informationChannel bank system Range BYou can hear the difference HDX noise reduction systemRF link Inherent Noise of the RF link Transmitter Mikroport System SpecificationsOFF EK 2015 receiverMm stereo jack plug, unbalanced Mm mono jack plug 102 Connector assignmentSK 2015 transmitter System variants and accessories 104 NT 3-USGarantiebestimmungen Garanzia prodotti Conditions de garantieDeclaración de garantia Page FCC DMOB2AUWG Opmerking BemerkungNota ObservaciónPage
Related manuals
Manual 4 pages 9.73 Kb