Vertex Standard FT-1000MP manual Installing Internal Accessories, TCXO-6 Installation

Page 114

Installing Internal Accessories

This section contains the installation procedures for installable options available for theMARK-VFT-1000MP. A complete list of options and their corresponding Yaesu P/N is provided on pages 5 and 6 of this manual. Please check with your dealer for pricing and availability.

Figure 1

Figure 2

TCXO UNIT

The Temperature-Compensated Crystal Oscillator is the heart of the master reference oscillator used throughout the transceiver. An optional TCXO unit is available for installation into the MARK-VFT-1000MP. The ±0.25-ppm TCXO-6replaces the factory-installed TCXO unit, and it provides enhanced frequency stabil- ity compared to the standard ±0.5-ppm module.

If you also have the optional YF-115CSub Receiver filter, now would be a good time to install it, as its mount- ing position is also exposed during the TCXO installa- tion procedures.

TCXO-6 Installation

rDisconnect all cables from the transceiver.

rReferring to Figure 1, remove the four screws (ð) on each side of the transceiver, and the seven screws (ž) from the bottom of the transceiver, then lift off the bottom cover.

rReferring to Figure 2, remove the six screws (Æ) from the top panel. Pry the top cover open and dis- connect the speaker cable from the speaker, then lift off the top and side covers.

rLocate the factory-installed TCXO UNIT in the front right corner of the chassis (see drawing below), and remove the wiring connector from the board. Use a small screwdriver to pry up the rear edge of the connector, and avoid pulling on the wires.

rRemove the four screws at the corners of the board, and remove the factory-installed TCXO UNIT.

rPosition the new TCXO-6in place, and use the same screws just removed to affix the new board in place.

rReinstall the wiring connector.

This completes the installation; connect the speaker cable to the speaker on the top cover, then replace the all covers and screws removed above (unless install- ing other options now).

page 112

MARK-V FT-1000MP Operating Manual

Image 114
Contents Vertex Standard Yaesu Europe B.VTabel of Contents General Description MARK-V FT-1000MP Operating ManualMARK-V FT-1000MP Operating Manual Transmitter SpecificationsGeneral ReceiverPLUG/CONNECTOR Pinout Diagrams Accessories & Options Supplied AccessoriesOptional Sub Receiver Filter If Crystal Filter OptionsOptional Main Receiver Filters Available OptionsSafety Precautions Power ConnectionsGround Connections Antenna Precautions Electrical Shock PreventionRF Field Exposure Advisory & Electromagnetic Compatibility Preliminary Inspection General SetupFP-29 Transceiver LocationAntenna Considerations Adjusting the Front FeetMemory Backup RG-8XQSK Accessory InstallationLinear Amplifier Interfacing Operation with QSK AmplifiersOperation with NON-QSK Amplifiers FL-2100SERIES or Others About ALC Transverter Operation Digital Modem TNC, WEATHERFAX, ETC. Interfacing Digital Modes with a TNC Or Computer Sound Card PSK-31MARK-V FT-1000MP TNC Accessory Installation Accessory Installation Other DIGITAL/RECORDING Device Interfacing FeaturesConfiguration Suggestions CW KEY/PADDLE and Computer Keying Interface SuggestionsLarge Receive Antennas Antenna ConnectionsPersonal Computer Interfacing for Contest SOFTWARE, ETC Front Panel Controls SUB AF Knob AF Gain RF Gain KnobRF PWR Knob Moni KnobCLASS-A Button Mode Selection ButtonsEdsp Filters Fast ButtonShuttle Jog and VRF & Idbt Buttons Main VFO-A Tuning KnobMain VFO-A RX & TX Switch-LED AF REV ButtonVFO & Memory Control Band KeypadSUB SQL Knob SUB VFO-B RX & TX Switch-LEDLock Button CW and Electronic Keyer ControlsNB Button NOR NAR ModeBandwidth Buttons NOR/NAR1/NAR2 Buttons 2nd and 3rd if Filter BandwidthVRF/MEM CH Knob VRF IndicatorTuner Button VRF/MEM CH Knob SequenceLCD Bargraph Meter Indications Wait Sub Receiver ModeMEM F HI SWRTOP Panel Access & Controls 12. CW PKTRtty Additional NoteCW Sidetone Trimmer Rear Panel Controls & ConnectorsRemote Jack Packet DIN JackBand Data DIN Jack DC in JackBefore Starting OperationKey Beeper Menu ProgrammingSpecial Note for CW Mode Reverse CW sideband Mode SelectionFast Button Operation VFO KnobShuttle Jog VRF/MEM CHMicrophone Up/Dwn Buttons Display SettingsPanel Up/Down Buttons VFO Channel SteppingVFO Selection & Receiver Muting Alternate VFO Operation Front & RearevfoToggle VFOs Keypad Frequency EntrySignal Tuning Meter Indications CW TuningRTTY/PKT Tuning Expanded Tuning Scale AM Synchronous TuningAM Synchronous Tuning SUB-DISPLAY Mode Selection AM Broadcast Reception General Coverage ReceptionMeter Frequency Band Range MHz Dealing with Interference Receiver Front End Configuration For illustrative purposesWide Band and Tuned Preamp Selection VRF Variable RF FRONT-END FilterRF Gain Setting IPO Intercept Point OptimizationAGC Automatic Gain Control Selection Main receiver VFO-A if Bandwidth Filter Selection Noise BlankerIf Filter Bandwidth Selection There are two banks of select Width Action Using Width control to reduce QRM Width ControlIf Shift Action SHIFT/WIDTH Tuning StepsUsing if Shift to reduce QRM Notch FilterAdvice on QRM Reduction Clarifier RX/TX Offset TuningClarifier Settings Offset Display ModeBand TX Range TransmittingAntenna Selection Selecting AntennasImportant Note Transmitter MonitorSSB Transmission Class-A Operation Microphone Tone SelectionRF Speech Processor Carrier Point OffsetVOX Operation Voice-Actuated T/R Switching Operation Straight-Key OperationCW Transmission Electronic Keyer Operation ACS Auto Character SpacingCW Straight Key and Paddle Connections Keyer Settings CW Pitch Setting and Spot ToneBaud Packet Digital Mode OperationRtty Operation AM TransmissionPacket Operation Baud FM PacketTNC Tone Pair Tone Center Frequency FM Repeater Operation FM TransmissionMain and Sub VFO Audio Dual ReceptionUsing Headphones for Dual Receive Headphone Audio AdjustmentsSplit Operation Mode SUB VFO-B SettingsSplit Frequency Operation Sideband Diversity Reception Bandwidth Diversity ReceptionVFO Tracking Memory Features Memory StructureRegarding the VRF/MEM CH Knob Basic Memory Storage ProcedureAuto Channel-Up Memory ProgrammingMemory Tuning Recalling & Operating on Memory ChannelsMemory Checking Limiting Memory Group Operation Copying a Selected Memory to VFO-A Grouping MemoriesCopying Between Memories QMB Quick Memory Bank Operation Memory Scanning Auto Memory WriteVFO Scanning Memory Scan SkipScan Resume Mode Scan Skip DisableMemory Masking Programmed Memory Scanning PMS Memories P1 ~ P9 Advanced Features Edsp Functions Edsp ModulationEdsp Contours Edsp RX Audio EnhancementEdsp Noise Reducer Edsp Auto Multiple Notch FilterEdsp Auto Multiple Notch Action Important Note About Edsp Introduction FeaturesRemote Control Operation Contest Keyer ControlUser Message Memories 1 Contest Number MemoryCQ or ID Memory Message StorageTune Mode Contest Keyer OperationIII. Main VFO-A Control II. VFO/MEMORY ControlComments USER-CUSTOMIZED Operating ModeOverview Sub VFO B Dial Main VFO a DialDVS-2 Controls Segment Message Recording PlaybackMessage Recording No Function SegmentMessage Transmission Receiver Recording withSelecting Receiver Audio Message MonitorPhone Patch Operation OperationTuning Meter RE-CALIBRATION Packet TuningOpcode CAT 5-BYTE Command StructureOverview CAT Data Protocol CAT Data Byte FormatDATA/ARGUMENT Bytes Constructing and Sending CAT Commands50 H 03 H 00 H 81 H 09 H 0A HStatus Flags Bytes 1~ Status Update Data OrganizationDownloading Memory Channel Data ByteStatus Flag Byte #2 Contents Status Flag Byte #1 ContentsStatus Flag Byte #4 Contents Status Flag Byte #5 ContentsMemory Channel Data Hex Codes Byte Data Record Structure Rtty PKT Coding Examples 0CH Opcode Command Chart0AH 0EHEdsp Command Parameter Bytes Opcode Or Key 1st 2rd 3rd 4th 5th70H 75HVFO RPT8AH 8CHFAH Byte Format F = 00H Byte Format F = 01HGrP3-cH GrP1-cHGrP2-cH GrP4-cHDiAL-SPd Auto-uPEdSP SJ-SPEEdSc-dL-ti Auto-inScAn-ALL NotcHBEEP SP-HoLdNot Used RF out BEEP-FSub-FiL CW norDAtAnAr2 FiLTonE SEt PAc-tonENot Used CtcSS RPt-SHFtLock-SEL Rc-FuncFASt-SEt PA-cntTunEr USEr-SEtSub-AGc CAr oFStCustom Frequency & Display Offset Information 1st Fc = F + 70.455 BFO kHzKHz 500 Hz 250 Hz PKT-F UserMenu Selection Setting Table Func No Function Setting Range DefaultSEPARATE/BALANCE Separate Main VFO-A/SUB VFO-BMONO/STEREO 1/STEREO Stereo NORMAL/REVERSE NormalDefault User Function Settings LSB USB CW USB CW LSB Rtty LSB Rtty USB PKT LSBEasy Set Mode Settings RX PLLTX PLL Installing Internal Accessories TCXO-6 InstallationMain Receiver 2ND and 3RD if Filters Filter InstallationInstallation SUB Receiver CW Narrow FilterLithium Battery Replacement Internal 13.8V Fuse ReplacementMemory BACK-UP Switch POWER-ON Microprocessor Reset Procedures MARK-V FT-1000MP Operating Manual