Vertex Standard FT-1000MP manual Message Recording Playback, No Function Segment

Page 84

Advanced Features

OPTIONAL DVS-2 DIGITAL VOICE RECORDER

MESSAGE RECORDING

PLAYBACK

(FROM MAIN OR SUB RECEIVER AUDIO)

(ON THE AIR OF RECORDED RECEIVER AUDIO)

When used in this mode, the DVS-2maintains a continuous recording of the last (approximately) 16 seconds of audio from either the main or sub-receiver. This can be particularly helpful in picking out callsigns during a pileup, as you can replay the same recording as often as you like (until you record over it). The record/ playback process in this mode is analogous to an 16- second “endless tape” - that is, you can turn the re- corder on and off to record up to a total of 16 seconds of small segments of audio, or you can leave the re- corder running to get one 16-second segment. In any case, the recorder overwrites data more than 16 (re- cording) seconds old.

rTo start the receiver recorder, just press the [REC] button. The yellow “REC” LED will light (and stay lit).

rWhen you hear something you want to play back, press the [STOP] button (the “REC” LED will turn off), and then press the [PLAY] button. Now the green “PLAY” LED will light as recorded audio is played back through the main receiver audio chan- nel.

Note that if you record for less than 16 seconds, playback will start at the point you first started record- ing (no “rewind” necessary). However, if you record for more than 16 seconds, playback will begin at the point 16 seconds before you stopped recording. In either case, playback will repeat any recorded audio every 16 seconds.

To stop the playback at any time, simply press [STOP]. If you then press [PLAY] again, playback will continue from the point you stopped it.

Once you have recorded an incoming transmission from another station, you can play it back to them by pressing the [PLAY] button on the DVS-2, followed im- mediately by the MOX switch on the front panel of the MARK-VFT-1000MP. This can be handy if you wish to advise another station of an anomalous signal condi- tion, for example.

Note: Communications-privacy regulations may re- quire you not to divulge the results of a prior contact (or a receiving session) to a third party. Consult the regulations for your country to ensure full compliance with your countries regulations.

MESSAGE RECORDING

(FROM MICROPHONE AUDIO)

This mode allows the DVS-2to record either two 8- second messages or four 4-second messages of au- dio from the microphone, such as contest exchanges or station IDs. Each can then be played back, either in monitor mode (without transmission), or directly over the air. Note that the digital memory used in this mode is independent from that used for receiver recording (so you can store both types of memory without inter- fering with one another).

The 8- and 4-second messages share the same memory, so two 4-second message segments (1 and 2 or 3 and 4) can be combined into one 8-second mes- sage for transmission, as indicated in the following table.

MEMORY SEGMENTS & MESSAGE NUMBERS

Button

Segment(s) Used in Record/Playback

 

 

2 x 8-second

4 x 4-second

Pressed

 

Message Mode

Message Mode

1

Segments 1 & 2

Segment 1

 

 

 

2

Segments 3 & 4

Segment 2

 

 

 

3

No Function

Segment 3

 

 

 

4

No Function

Segment 4

Before you record for transmission, check that the [MESSAGE MODE] Switch is set for the size message you want to record, either 4-second or 8-second (see the table above and the Example in the next section for help with this decision). You do not need to press the PTT switch while recording a message, although you can, in which case your audio will be transmitted and recorded simultaneously.

page 82

MARK-V FT-1000MP Operating Manual

Image 84
Contents Vertex Standard Yaesu Europe B.VTabel of Contents General Description MARK-V FT-1000MP Operating ManualMARK-V FT-1000MP Operating Manual Specifications GeneralTransmitter ReceiverPLUG/CONNECTOR Pinout Diagrams Accessories & Options Supplied AccessoriesIf Crystal Filter Options Optional Main Receiver FiltersOptional Sub Receiver Filter Available OptionsSafety Precautions Power ConnectionsGround Connections Antenna Precautions Electrical Shock PreventionRF Field Exposure Advisory & Electromagnetic Compatibility General Setup FP-29Preliminary Inspection Transceiver LocationAdjusting the Front Feet Memory BackupAntenna Considerations RG-8XAccessory Installation Linear Amplifier InterfacingQSK Operation with QSK AmplifiersOperation with NON-QSK Amplifiers FL-2100SERIES or Others About ALC Transverter Operation Digital Modem TNC, WEATHERFAX, ETC. Interfacing Digital Modes with a TNC Or Computer Sound Card PSK-31MARK-V FT-1000MP TNC Accessory Installation Accessory Installation Features Configuration SuggestionsOther DIGITAL/RECORDING Device Interfacing CW KEY/PADDLE and Computer Keying Interface SuggestionsLarge Receive Antennas Antenna ConnectionsPersonal Computer Interfacing for Contest SOFTWARE, ETC Front Panel Controls AF Gain RF Gain Knob RF PWR KnobSUB AF Knob Moni KnobMode Selection Buttons Edsp FiltersCLASS-A Button Fast ButtonMain VFO-A Tuning Knob Main VFO-A RX & TX Switch-LEDShuttle Jog and VRF & Idbt Buttons AF REV ButtonVFO & Memory Control Band KeypadSUB VFO-B RX & TX Switch-LED Lock ButtonSUB SQL Knob CW and Electronic Keyer ControlsNOR NAR Mode Bandwidth Buttons NOR/NAR1/NAR2 ButtonsNB Button 2nd and 3rd if Filter BandwidthVRF Indicator Tuner ButtonVRF/MEM CH Knob VRF/MEM CH Knob SequenceLCD Bargraph Meter Indications Sub Receiver Mode MEM FWait HI SWRTOP Panel Access & Controls PKT Rtty12. CW Additional NoteRear Panel Controls & Connectors Remote JackCW Sidetone Trimmer Packet DIN JackBand Data DIN Jack DC in JackOperation Key BeeperBefore Starting Menu ProgrammingSpecial Note for CW Mode Reverse CW sideband Mode SelectionVFO Knob Shuttle JogFast Button Operation VRF/MEM CHDisplay Settings Panel Up/Down ButtonsMicrophone Up/Dwn Buttons VFO Channel SteppingAlternate VFO Operation Front & Rearevfo Toggle VFOsVFO Selection & Receiver Muting Keypad Frequency EntrySignal Tuning Meter Indications CW TuningRTTY/PKT Tuning Expanded Tuning Scale AM Synchronous TuningAM Synchronous Tuning SUB-DISPLAY Mode Selection AM Broadcast Reception General Coverage ReceptionMeter Frequency Band Range MHz Receiver Front End Configuration For illustrative purposes Wide Band and Tuned Preamp SelectionDealing with Interference VRF Variable RF FRONT-END FilterRF Gain Setting IPO Intercept Point OptimizationAGC Automatic Gain Control Selection Main receiver VFO-A if Bandwidth Filter Selection Noise BlankerIf Filter Bandwidth Selection There are two banks of select Width Action Using Width control to reduce QRM Width ControlSHIFT/WIDTH Tuning Steps Using if Shift to reduce QRMIf Shift Action Notch FilterAdvice on QRM Reduction Clarifier RX/TX Offset TuningClarifier Settings Offset Display ModeTransmitting Antenna SelectionBand TX Range Selecting AntennasImportant Note Transmitter MonitorSSB Transmission Microphone Tone Selection RF Speech ProcessorClass-A Operation Carrier Point OffsetVOX Operation Voice-Actuated T/R Switching Operation Straight-Key OperationCW Transmission Electronic Keyer Operation ACS Auto Character SpacingCW Straight Key and Paddle Connections Keyer Settings CW Pitch Setting and Spot ToneDigital Mode Operation Rtty OperationBaud Packet AM TransmissionPacket Operation Baud FM PacketTNC Tone Pair Tone Center Frequency FM Repeater Operation FM TransmissionMain and Sub VFO Audio Dual ReceptionUsing Headphones for Dual Receive Headphone Audio AdjustmentsSplit Operation Mode SUB VFO-B SettingsSplit Frequency Operation Sideband Diversity Reception Bandwidth Diversity ReceptionVFO Tracking Memory Features Memory StructureBasic Memory Storage Procedure Auto Channel-UpRegarding the VRF/MEM CH Knob Memory ProgrammingMemory Tuning Recalling & Operating on Memory ChannelsMemory Checking Limiting Memory Group Operation Copying a Selected Memory to VFO-A Grouping MemoriesCopying Between Memories QMB Quick Memory Bank Operation Auto Memory Write VFO ScanningMemory Scanning Memory Scan SkipScan Resume Mode Scan Skip DisableMemory Masking Programmed Memory Scanning PMS Memories P1 ~ P9 Advanced Features Edsp Modulation Edsp ContoursEdsp Functions Edsp RX Audio EnhancementEdsp Noise Reducer Edsp Auto Multiple Notch FilterEdsp Auto Multiple Notch Action Important Note About Edsp Features Remote Control OperationIntroduction Contest Keyer ControlContest Number Memory CQ or ID MemoryUser Message Memories 1 Message StorageTune Mode Contest Keyer OperationIII. Main VFO-A Control II. VFO/MEMORY ControlUSER-CUSTOMIZED Operating Mode OverviewComments Sub VFO B Dial Main VFO a DialDVS-2 Controls Message Recording Playback Message RecordingSegment No Function SegmentReceiver Recording with Selecting Receiver AudioMessage Transmission Message MonitorPhone Patch Operation OperationTuning Meter RE-CALIBRATION Packet TuningCAT 5-BYTE Command Structure Overview CAT Data ProtocolOpcode CAT Data Byte FormatConstructing and Sending CAT Commands 50 H 03 H 00 H 81 H 09 HDATA/ARGUMENT Bytes 0A HStatus Update Data Organization DownloadingStatus Flags Bytes 1~ Memory Channel Data ByteStatus Flag Byte #1 Contents Status Flag Byte #4 ContentsStatus Flag Byte #2 Contents Status Flag Byte #5 ContentsMemory Channel Data Hex Codes Byte Data Record Structure Rtty PKT Coding Examples Opcode Command Chart 0AH0CH 0EHCommand Parameter Bytes Opcode Or Key 1st 2rd 3rd 4th 5th 70HEdsp 75HRPT 8AHVFO 8CHFAH Byte Format F = 00H Byte Format F = 01HGrP1-cH GrP2-cHGrP3-cH GrP4-cHAuto-uP EdSPDiAL-SPd SJ-SPEEdAuto-in ScAn-ALLSc-dL-ti NotcHSP-HoLd Not Used RF outBEEP BEEP-FCW nor DAtAnAr2Sub-FiL FiLPAc-tonE Not Used CtcSSTonE SEt RPt-SHFtRc-Func FASt-SEtLock-SEL PA-cntUSEr-SEt Sub-AGcTunEr CAr oFStCustom Frequency & Display Offset Information 1st Fc = F + 70.455 BFO kHzKHz 500 Hz 250 Hz PKT-F UserMenu Selection Setting Table Func No Function Setting Range DefaultMain VFO-A/SUB VFO-B MONO/STEREO 1/STEREO StereoSEPARATE/BALANCE Separate NORMAL/REVERSE NormalDefault User Function Settings LSB USB CW USB CW LSB Rtty LSB Rtty USB PKT LSBEasy Set Mode Settings RX PLLTX PLL Installing Internal Accessories TCXO-6 InstallationFilter Installation InstallationMain Receiver 2ND and 3RD if Filters SUB Receiver CW Narrow FilterLithium Battery Replacement Internal 13.8V Fuse ReplacementMemory BACK-UP Switch POWER-ON Microprocessor Reset Procedures MARK-V FT-1000MP Operating Manual