Vertex Standard FT-1000MP manual Rc-Func, FASt-SEt, Lock-SEL, PA-cnt, FrontEnd, Ant-SEL

Page 106

Menu Selection and Settings

7-9 rc-Func

8-2 SPLt-SEt

Remote Control Function - Selects the active fea- ture for remote control operation.

Note - Remote control operation requires a FH-1Remote Control Keypad for operation; see the descrip- tion and charts on pages 76 ~ 79 for details of opera- tion.

Keyer - Activates the contest keyer operation.

Function Keys - Emulate front panel Memory Con- trol keys.

VFO-A - Enables direct-frequency input to VFO-A by emulating the front panel keypad keys.

VFO-B - Enables direct-frequency input to VFO-B by emulating the front panel keypad keys.

If you wish to exercise remote control of the VL- 1000 Linear Amplifier from the MARK-VFT-1000MP, this menu must be set to “Keyer.”

8-0 FASt-SEt

FAST Button Operation - Selects front-panel [FAST] button actuation:

Momentary - Press and hold to engage fast tuning.

Continuous - Toggle on/toggle off fast tuning.

8-1 Lock-SEL

LOCK Button Operation - Sets up the panel “Lock” mode:

Dial - Locks MAIN VFO-A knob only.

Panel - Locks front panel buttons & keys (refer to drawing below).

Primary - locks front panel primary function keys (refer to drawing below).

Split Mode Operation - Select one of three split operating modes:

Normal - In this mode, pressing SUB VFO-B (TX) Switch-LEDactivates SUB VFO-B for transmission. Other settings (such as mode and frequency) must be manually set for the Sub VFO.

Auto - When the SUB VFO-B (TX) Switch/LED is pressed, SUB VFO-B is enabled for transmit, and the selected operating mode from MAIN VFO-A is automatically copied into SUB VFO-B.

A=B - Same as Auto mode above; however, a pre- set frequency offset is applied to SUB VFO-B for transmission (see menu selection 1-6: Quick Split).

8-3 PA-cnt

Power Amplifier - Enable/Disable the Power Am- plifier. When you are using a transverter, select this menu to “PA off.”

8-4 FrontEnd

Receiver Front-End RF Amplifier - Selects the de-

sired receiver front-end amplifier configuration:

Flat - A broadband amplifier with flat response.

Tuned - A separate tuned amplifier for the low and high bands.

8-5 Ant-SEL

Antenna Selection - Sets up the rear-panel an- tenna jack switching:

AUTO - Antenna selections are automatically cop- ied along with other operating parameters during memory programming.

ON - Enables the front panel [ANT] switch.

OFF - Disables the front panel [ANT] switch (only ANT-A is therefore available).

Panel Lock

When the Main VFO (A) [LOCK] button is pressed, all controls within the shaded area (except VRF and IDBT switches).

When the Sub VFO (B) [LOCK] button is pressed, only the SUB VFO Tuning knob.

Primary Lock

When the Main VFO (A) [LOCK] button is pressed, only the MAIN VFO Tuning knob.

When the Sub VFO (B) [LOCK] button is pressed, all controls within the shaded area.

page 104

MARK-V FT-1000MP Operating Manual

Page 105 Page 107
Image 106
Page 105 Page 107
Contents Vertex Standard Yaesu Europe B.VTabel of Contents General Description MARK-V FT-1000MP Operating ManualMARK-V FT-1000MP Operating Manual Transmitter SpecificationsGeneral ReceiverPLUG/CONNECTOR Pinout Diagrams Accessories & Options Supplied AccessoriesOptional Sub Receiver Filter If Crystal Filter OptionsOptional Main Receiver Filters Available OptionsPower Connections Safety PrecautionsGround Connections Electrical Shock Prevention Antenna PrecautionsRF Field Exposure Advisory & Electromagnetic Compatibility Preliminary Inspection General SetupFP-29 Transceiver LocationAntenna Considerations Adjusting the Front FeetMemory Backup RG-8XQSK Accessory InstallationLinear Amplifier Interfacing Operation with QSK AmplifiersOperation with NON-QSK Amplifiers FL-2100SERIES or Others About ALC Transverter Operation Digital Modem TNC, WEATHERFAX, ETC. Interfacing Digital Modes with a TNC Or Computer Sound Card PSK-31MARK-V FT-1000MP TNC Accessory Installation Accessory Installation Other DIGITAL/RECORDING Device Interfacing FeaturesConfiguration Suggestions CW KEY/PADDLE and Computer Keying Interface SuggestionsLarge Receive Antennas Antenna ConnectionsPersonal Computer Interfacing for Contest SOFTWARE, ETC Front Panel Controls SUB AF Knob AF Gain RF Gain KnobRF PWR Knob Moni KnobCLASS-A Button Mode Selection ButtonsEdsp Filters Fast ButtonShuttle Jog and VRF & Idbt Buttons Main VFO-A Tuning KnobMain VFO-A RX & TX Switch-LED AF REV ButtonVFO & Memory Control Band KeypadSUB SQL Knob SUB VFO-B RX & TX Switch-LEDLock Button CW and Electronic Keyer ControlsNB Button NOR NAR ModeBandwidth Buttons NOR/NAR1/NAR2 Buttons 2nd and 3rd if Filter BandwidthVRF/MEM CH Knob VRF IndicatorTuner Button VRF/MEM CH Knob SequenceLCD Bargraph Meter Indications Wait Sub Receiver ModeMEM F HI SWRTOP Panel Access & Controls 12. CW PKTRtty Additional NoteCW Sidetone Trimmer Rear Panel Controls & ConnectorsRemote Jack Packet DIN JackBand Data DIN Jack DC in JackBefore Starting OperationKey Beeper Menu ProgrammingSpecial Note for CW Mode Reverse CW sideband Mode SelectionFast Button Operation VFO KnobShuttle Jog VRF/MEM CHMicrophone Up/Dwn Buttons Display SettingsPanel Up/Down Buttons VFO Channel SteppingVFO Selection & Receiver Muting Alternate VFO Operation Front & RearevfoToggle VFOs Keypad Frequency EntryCW Tuning Signal Tuning Meter IndicationsRTTY/PKT Tuning AM Synchronous Tuning Expanded Tuning ScaleAM Synchronous Tuning SUB-DISPLAY Mode Selection General Coverage Reception AM Broadcast ReceptionMeter Frequency Band Range MHz Dealing with Interference Receiver Front End Configuration For illustrative purposesWide Band and Tuned Preamp Selection VRF Variable RF FRONT-END FilterIPO Intercept Point Optimization RF Gain SettingAGC Automatic Gain Control Selection Noise Blanker Main receiver VFO-A if Bandwidth Filter SelectionIf Filter Bandwidth Selection There are two banks of select Width Action Using Width control to reduce QRM Width ControlIf Shift Action SHIFT/WIDTH Tuning StepsUsing if Shift to reduce QRM Notch FilterAdvice on QRM Reduction Clarifier RX/TX Offset TuningClarifier Settings Offset Display ModeBand TX Range TransmittingAntenna Selection Selecting AntennasTransmitter Monitor Important NoteSSB Transmission Class-A Operation Microphone Tone SelectionRF Speech Processor Carrier Point OffsetStraight-Key Operation VOX Operation Voice-Actuated T/R Switching OperationCW Transmission ACS Auto Character Spacing Electronic Keyer OperationCW Straight Key and Paddle Connections Keyer Settings CW Pitch Setting and Spot ToneBaud Packet Digital Mode OperationRtty Operation AM TransmissionBaud FM Packet Packet OperationTNC Tone Pair Tone Center Frequency FM Repeater Operation FM TransmissionMain and Sub VFO Audio Dual ReceptionUsing Headphones for Dual Receive Headphone Audio AdjustmentsSUB VFO-B Settings Split Operation ModeSplit Frequency Operation Bandwidth Diversity Reception Sideband Diversity ReceptionVFO Tracking Memory Features Memory StructureRegarding the VRF/MEM CH Knob Basic Memory Storage ProcedureAuto Channel-Up Memory ProgrammingRecalling & Operating on Memory Channels Memory TuningMemory Checking Copying a Selected Memory to VFO-A Grouping Memories Limiting Memory Group OperationCopying Between Memories QMB Quick Memory Bank Operation Memory Scanning Auto Memory WriteVFO Scanning Memory Scan SkipScan Skip Disable Scan Resume ModeMemory Masking Programmed Memory Scanning PMS Memories P1 ~ P9 Advanced Features Edsp Functions Edsp ModulationEdsp Contours Edsp RX Audio EnhancementEdsp Auto Multiple Notch Filter Edsp Noise ReducerEdsp Auto Multiple Notch Action Important Note About Edsp Introduction FeaturesRemote Control Operation Contest Keyer ControlUser Message Memories 1 Contest Number MemoryCQ or ID Memory Message StorageTune Mode Contest Keyer OperationIII. Main VFO-A Control II. VFO/MEMORY ControlComments USER-CUSTOMIZED Operating ModeOverview Sub VFO B Dial Main VFO a DialDVS-2 Controls Segment Message Recording PlaybackMessage Recording No Function SegmentMessage Transmission Receiver Recording withSelecting Receiver Audio Message MonitorPhone Patch Operation OperationTuning Meter RE-CALIBRATION Packet TuningOpcode CAT 5-BYTE Command StructureOverview CAT Data Protocol CAT Data Byte FormatDATA/ARGUMENT Bytes Constructing and Sending CAT Commands50 H 03 H 00 H 81 H 09 H 0A HStatus Flags Bytes 1~ Status Update Data OrganizationDownloading Memory Channel Data ByteStatus Flag Byte #2 Contents Status Flag Byte #1 ContentsStatus Flag Byte #4 Contents Status Flag Byte #5 ContentsMemory Channel Data Hex Codes Byte Data Record Structure Rtty PKT Coding Examples 0CH Opcode Command Chart0AH 0EHEdsp Command Parameter Bytes Opcode Or Key 1st 2rd 3rd 4th 5th70H 75HVFO RPT8AH 8CHFAH Byte Format F = 00H Byte Format F = 01HGrP3-cH GrP1-cHGrP2-cH GrP4-cHDiAL-SPd Auto-uPEdSP SJ-SPEEdSc-dL-ti Auto-inScAn-ALL NotcHBEEP SP-HoLdNot Used RF out BEEP-FSub-FiL CW norDAtAnAr2 FiLTonE SEt PAc-tonENot Used CtcSS RPt-SHFtLock-SEL Rc-FuncFASt-SEt PA-cntTunEr USEr-SEtSub-AGc CAr oFStCustom Frequency & Display Offset Information 1st Fc = F + 70.455 BFO kHzKHz 500 Hz 250 Hz PKT-F UserMenu Selection Setting Table Func No Function Setting Range DefaultSEPARATE/BALANCE Separate Main VFO-A/SUB VFO-BMONO/STEREO 1/STEREO Stereo NORMAL/REVERSE NormalDefault User Function Settings LSB USB CW USB CW LSB Rtty LSB Rtty USB PKT LSBRX PLL Easy Set Mode SettingsTX PLL Installing Internal Accessories TCXO-6 InstallationMain Receiver 2ND and 3RD if Filters Filter InstallationInstallation SUB Receiver CW Narrow FilterInternal 13.8V Fuse Replacement Lithium Battery ReplacementMemory BACK-UP Switch POWER-ON Microprocessor Reset Procedures MARK-V FT-1000MP Operating Manual
Top Page Image Contents