Vertex Standard FT-1000MP manual Bandwidth Buttons NOR/NAR1/NAR2 Buttons, NB Button, NOR NAR Mode

Page 30

FRONT PANEL CONTROLS

48. BANDWIDTH Buttons (NOR/NAR1/NAR2) Buttons

These three buttons select the 2nd and 3rd IF fil- ters for the receiver (except in the FM mode). The LED inside each button glows red when the corresponding bandwidth is selected.

The available 2nd and 3rd IF filters are as follows:

49.NB Button

Pressing this button activates the IF Noise Blanker, which may help reduce many different types of man- made impulse noise (but not atmospherics). When the Noise Blanker is activated, the LED inside button will glow red.

You can select the Noise Blanker Type (for short- duration pulses or for long-duration pulses) and its blanking level via menu selection 2-8.

2nd and 3rd IF Filter Bandwidth

 

 

NOR

NAR 1

NAR 2

 

 

MODE

2nd IF

3rd IF

2nd IF

3rd IF

2nd IF

3rd IF

 

 

 

(8.2MHz)

(455 kHz)

(8.2MHz)

(455 kHz)

(8.2MHz)

(455 kHz)

 

 

SSB

2.4 kHz/ATTø1

2.4/6.0 kHzø1

2.0 (2.4) kHz

2.0 (2.4) kHz

N/A (2.0 kHz)

N/A (2.0 kHz)

 

 

CW

2.0/2.4 kHzø2

2.0/2.4 kHzø2

500 Hz

500 Hz

250 Hz

250 Hz

 

 

AM

ATT

6.0 kHz

2.4 kHz

2.4 kHz

2.0 kHz

2.0 kHz

 

 

RTTY/PKT/USER

2.4 kHz

2.4 kHz

2.0 kHz

2.0 kHz

250/500 Hzø3

250/500 Hzø3

 

ø1: You can select the bandwidth via menu selection 5-0. The first value (bandwidth) is factory default.

ø2: You can select the bandwidth via menu selection 5-2. The first value (bandwidth) is factory default.

ø3: You can select the bandwidth via menu selection 5-4. The first value (bandwidth) is factory default.

Note 1 - In the factory default condition, the SSB NAR 1 bandwidth is “2.0 kHz/2.0 kHz (2nd IF/3rd IF)” and the SSB NAR 2 bandwidth is disabled. If you set the SSB NOR bandwidth to “ATT/6.0 kHz (2nd IF/3rd IF)” via menu selection 5- 0, the NAR 1 bandwidth will be set to “2.4 kHz/2.4 kHz (2nd IF/3rd IF)” and the NAR 2 bandwidth will be set to “2.0 kHz/ 2.0 kHz (2nd IF/3rd IF)” automatically.

Note 2 - The 2nd IF (8.2 MHz) 2.0-kHz BW filter (Yaesu P/N YF-114SN) and 250 Hz BW filter (Yaesu P/N YF-114CN) and 3rd IF (455 kHz) 2.0-kHz BW filter (Yaesu P/N YF-110SN), 500 Hz BW filter (Yaesu P/N YF-115C) and 250 Hz BW filter (Yaesu P/N YF-110CN) are option.

Note 3 - The Sub Receiver use a double-conversion circuit with 47.21 MHz and 455 kHz intermediate frequencies. Both the 6.0 kHz and 2.4 kHz filters are selected automatically according to mode, and with the optional 500 Hz Collins me- chanical filter (Yaesu P/N YF-115C) installed and enabled via menu programming, it can be selected for CW operation.

page 28

MARK-V FT-1000MP Operating Manual

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Vertex Standard Yaesu Europe B.VTabel of Contents General Description MARK-V FT-1000MP Operating ManualMARK-V FT-1000MP Operating Manual Transmitter SpecificationsGeneral ReceiverPLUG/CONNECTOR Pinout Diagrams Accessories & Options Supplied AccessoriesOptional Sub Receiver Filter If Crystal Filter OptionsOptional Main Receiver Filters Available OptionsSafety Precautions Power ConnectionsGround Connections Antenna Precautions Electrical Shock PreventionRF Field Exposure Advisory & Electromagnetic Compatibility Preliminary Inspection General SetupFP-29 Transceiver LocationAntenna Considerations Adjusting the Front FeetMemory Backup RG-8XQSK Accessory InstallationLinear Amplifier Interfacing Operation with QSK AmplifiersOperation with NON-QSK Amplifiers FL-2100SERIES or Others About ALC Transverter Operation Digital Modem TNC, WEATHERFAX, ETC. Interfacing Digital Modes with a TNC Or Computer Sound Card PSK-31MARK-V FT-1000MP TNC Accessory Installation Accessory Installation Other DIGITAL/RECORDING Device Interfacing FeaturesConfiguration Suggestions CW KEY/PADDLE and Computer Keying Interface SuggestionsLarge Receive Antennas Antenna ConnectionsPersonal Computer Interfacing for Contest SOFTWARE, ETC Front Panel Controls SUB AF Knob AF Gain RF Gain KnobRF PWR Knob Moni KnobCLASS-A Button Mode Selection ButtonsEdsp Filters Fast Button Shuttle Jog and VRF & Idbt Buttons Main VFO-A Tuning Knob Main VFO-A RX & TX Switch-LED AF REV ButtonVFO & Memory Control Band KeypadSUB SQL Knob SUB VFO-B RX & TX Switch-LEDLock Button CW and Electronic Keyer ControlsNB Button NOR NAR ModeBandwidth Buttons NOR/NAR1/NAR2 Buttons 2nd and 3rd if Filter BandwidthVRF/MEM CH Knob VRF IndicatorTuner Button VRF/MEM CH Knob SequenceLCD Bargraph Meter Indications Wait Sub Receiver ModeMEM F HI SWRTOP Panel Access & Controls 12. CW PKTRtty Additional NoteCW Sidetone Trimmer Rear Panel Controls & ConnectorsRemote Jack Packet DIN JackBand Data DIN Jack DC in JackBefore Starting OperationKey Beeper Menu ProgrammingSpecial Note for CW Mode Reverse CW sideband Mode SelectionFast Button Operation VFO KnobShuttle Jog VRF/MEM CHMicrophone Up/Dwn Buttons Display SettingsPanel Up/Down Buttons VFO Channel SteppingVFO Selection & Receiver Muting Alternate VFO Operation Front & RearevfoToggle VFOs Keypad Frequency EntrySignal Tuning Meter Indications CW TuningRTTY/PKT Tuning Expanded Tuning Scale AM Synchronous TuningAM Synchronous Tuning SUB-DISPLAY Mode Selection AM Broadcast Reception General Coverage ReceptionMeter Frequency Band Range MHz Dealing with Interference Receiver Front End Configuration For illustrative purposesWide Band and Tuned Preamp Selection VRF Variable RF FRONT-END FilterRF Gain Setting IPO Intercept Point OptimizationAGC Automatic Gain Control Selection Main receiver VFO-A if Bandwidth Filter Selection Noise BlankerIf Filter Bandwidth Selection There are two banks of select Width Action Using Width control to reduce QRM Width ControlIf Shift Action SHIFT/WIDTH Tuning StepsUsing if Shift to reduce QRM Notch FilterAdvice on QRM Reduction Clarifier RX/TX Offset TuningClarifier Settings Offset Display ModeBand TX Range TransmittingAntenna Selection Selecting AntennasImportant Note Transmitter MonitorSSB Transmission Class-A Operation Microphone Tone SelectionRF Speech Processor Carrier Point OffsetVOX Operation Voice-Actuated T/R Switching Operation Straight-Key OperationCW Transmission Electronic Keyer Operation ACS Auto Character SpacingCW Straight Key and Paddle Connections Keyer Settings CW Pitch Setting and Spot ToneBaud Packet Digital Mode OperationRtty Operation AM TransmissionPacket Operation Baud FM PacketTNC Tone Pair Tone Center Frequency FM Repeater Operation FM TransmissionMain and Sub VFO Audio Dual ReceptionUsing Headphones for Dual Receive Headphone Audio AdjustmentsSplit Operation Mode SUB VFO-B SettingsSplit Frequency Operation Sideband Diversity Reception Bandwidth Diversity ReceptionVFO Tracking Memory Features Memory StructureRegarding the VRF/MEM CH Knob Basic Memory Storage ProcedureAuto Channel-Up Memory ProgrammingMemory Tuning Recalling & Operating on Memory ChannelsMemory Checking Limiting Memory Group Operation Copying a Selected Memory to VFO-A Grouping MemoriesCopying Between Memories QMB Quick Memory Bank Operation Memory Scanning Auto Memory WriteVFO Scanning Memory Scan SkipScan Resume Mode Scan Skip DisableMemory Masking Programmed Memory Scanning PMS Memories P1 ~ P9 Advanced Features Edsp Functions Edsp ModulationEdsp Contours Edsp RX Audio EnhancementEdsp Noise Reducer Edsp Auto Multiple Notch FilterEdsp Auto Multiple Notch Action Important Note About Edsp Introduction FeaturesRemote Control Operation Contest Keyer ControlUser Message Memories 1 Contest Number MemoryCQ or ID Memory Message StorageTune Mode Contest Keyer OperationIII. Main VFO-A Control II. VFO/MEMORY ControlComments USER-CUSTOMIZED Operating ModeOverview Sub VFO B Dial Main VFO a DialDVS-2 Controls Segment Message Recording PlaybackMessage Recording No Function SegmentMessage Transmission Receiver Recording withSelecting Receiver Audio Message MonitorPhone Patch Operation OperationTuning Meter RE-CALIBRATION Packet TuningOpcode CAT 5-BYTE Command StructureOverview CAT Data Protocol CAT Data Byte FormatDATA/ARGUMENT Bytes Constructing and Sending CAT Commands50 H 03 H 00 H 81 H 09 H 0A HStatus Flags Bytes 1~ Status Update Data OrganizationDownloading Memory Channel Data ByteStatus Flag Byte #2 Contents Status Flag Byte #1 ContentsStatus Flag Byte #4 Contents Status Flag Byte #5 ContentsMemory Channel Data Hex Codes Byte Data Record Structure Rtty PKT Coding Examples 0CH Opcode Command Chart0AH 0EHEdsp Command Parameter Bytes Opcode Or Key 1st 2rd 3rd 4th 5th70H 75HVFO RPT8AH 8CHFAH Byte Format F = 00H Byte Format F = 01HGrP3-cH GrP1-cHGrP2-cH GrP4-cHDiAL-SPd Auto-uPEdSP SJ-SPEEdSc-dL-ti Auto-inScAn-ALL NotcHBEEP SP-HoLdNot Used RF out BEEP-FSub-FiL CW norDAtAnAr2 FiLTonE SEt PAc-tonENot Used CtcSS RPt-SHFtLock-SEL Rc-FuncFASt-SEt PA-cntTunEr USEr-SEtSub-AGc CAr oFStCustom Frequency & Display Offset Information 1st Fc = F + 70.455 BFO kHzKHz 500 Hz 250 Hz PKT-F UserMenu Selection Setting Table Func No Function Setting Range DefaultSEPARATE/BALANCE Separate Main VFO-A/SUB VFO-BMONO/STEREO 1/STEREO Stereo NORMAL/REVERSE NormalDefault User Function Settings LSB USB CW USB CW LSB Rtty LSB Rtty USB PKT LSBEasy Set Mode Settings RX PLLTX PLL Installing Internal Accessories TCXO-6 InstallationMain Receiver 2ND and 3RD if Filters Filter InstallationInstallation SUB Receiver CW Narrow FilterLithium Battery Replacement Internal 13.8V Fuse ReplacementMemory BACK-UP Switch POWER-ON Microprocessor Reset Procedures MARK-V FT-1000MP Operating Manual
Top Page Image Contents