Vertex Standard FT-1000MP Panel Up/Down Buttons, Microphone Up/Dwn Buttons, VFO Channel Stepping

Page 41

OPERATION

RECEIVING

Panel Up/Down Buttons

Press the large UP(p) and DOWN(q) buttons below the key- pad to step around the band in 100-kHz steps, and then tune around the band a bit with the tuning knob.

If the “FAST” icon appears on the display, pressing these buttons will cause stepping in 1 MHz increments.

Microphone Up/Dwn Buttons

If your microphone has UP and DWN buttons, (such as the MH-31B8D) you can press them momentarily to tune in 10-Hz steps, or hold them to start VFO scan- ning. If it has a FST button, you can use it to duplicate the function of the [FAST] key on the transceiver front panel.

VFO Channel Stepping

This feature utilizes the VRF/MEM CH knob at the upper right corner, and i s u n i q u e b e c a u s e i t a l l o w s “channellizing” the VFO for quick, yet precise, frequency navigation. For ex- ample, setting this feature to 1 kHz pro- vides an easy wasy of steping around an SSB band, looking for activity. Many bands such as AM broad- cast, HF maritime, aeronautical, and citizen’s band in- corporate assigned channels using discrete frequency steps. By configuring this feature for the service in in- terest, you can hop from one channel to the next with- out having to zero in (manually) each station’s signal with the VFO knob.

To enable operation using the VFO Step feature, it first must be enabled by press and holding the VRF/ MEM CH knob for ½ second.

Once enabled, rotating VRF/MEM CH knob as you would to tune a channelized FM rig. While VFO chan- nel stepping is enabled, “- - - -” appears in the channel number display, until the knob is pressed in again to disable channel stepping. Channel stepping is config- ured by menu selection 1-5on page 99; also see Gen- eral Coverage Reception.

To disable the VFO Step feature, just press the VRF/ MEM CH knob momentarily.

Display Settings

Display Mode - By default, switching to and from CW, PKT or RTTY modes causes the display to change by the amount of offset selected by the CW PITCH (page 56), RTTY, and PKT tone & offset configurations (pages 15 and 16). If you prefer the display to remain unchanged when switching modes, this can be done by setting menu selection 3-0to BFO (carrier) display on page 100. However, the actual carrier offsets configured by the menu selections, relative to the display and IF bandpass are unaffected, regardless of the setting for menu selection 3-0.

Display Resolution - Although the MARK-V FT- 1000MP DDS (Direct Digital Synthesizer) tunes in frequency increments as small as .625 Hz, display resolution is limited to 10 Hz. The 10 Hz and 100 Hz digits display can be turned off, as desired, if smaller frequency resolution is not needed (tuning steps are not affected).

Select the desired display resolution via menu se- lection 3-1on page 100.

VFO & Panel Locking Schemes

The locking scheme for the MAIN VFO-A [LOCK] button offers three choices. By default, pressing the [LOCK] button so that “LOCK” appears only disables the tuning knob (it still turns, but does noth- ing). However, it can disable all front panel keys, or else all except the primary function keys. To se- lect the locking scheme, recall menu function 8-1, as shown on page 104.

Important! - Holding the [LOCK] button without releasing it activates the dual VFO tracking fea- ture, which is discussed later in the chapter.

MARK-V FT-1000MP Operating Manual

page 39

Image 41
Contents Yaesu Europe B.V Vertex StandardTabel of Contents MARK-V FT-1000MP Operating Manual General DescriptionMARK-V FT-1000MP Operating Manual General SpecificationsTransmitter ReceiverPLUG/CONNECTOR Pinout Diagrams Supplied Accessories Accessories & OptionsOptional Main Receiver Filters If Crystal Filter OptionsOptional Sub Receiver Filter Available OptionsGround Connections Safety PrecautionsPower Connections RF Field Exposure Advisory & Electromagnetic Compatibility Antenna PrecautionsElectrical Shock Prevention FP-29 General SetupPreliminary Inspection Transceiver LocationMemory Backup Adjusting the Front FeetAntenna Considerations RG-8XLinear Amplifier Interfacing Accessory InstallationQSK Operation with QSK AmplifiersOperation with NON-QSK Amplifiers FL-2100SERIES or Others About ALC Transverter Operation Digital Modes with a TNC Or Computer Sound Card PSK-31 Digital Modem TNC, WEATHERFAX, ETC. InterfacingMARK-V FT-1000MP TNC Accessory Installation Accessory Installation Configuration Suggestions FeaturesOther DIGITAL/RECORDING Device Interfacing CW KEY/PADDLE and Computer Keying Interface SuggestionsAntenna Connections Large Receive AntennasPersonal Computer Interfacing for Contest SOFTWARE, ETC Front Panel Controls RF PWR Knob AF Gain RF Gain KnobSUB AF Knob Moni KnobEdsp Filters Mode Selection ButtonsCLASS-A Button Fast ButtonMain VFO-A RX & TX Switch-LED Main VFO-A Tuning KnobShuttle Jog and VRF & Idbt Buttons AF REV ButtonBand Keypad VFO & Memory ControlLock Button SUB VFO-B RX & TX Switch-LEDSUB SQL Knob CW and Electronic Keyer ControlsBandwidth Buttons NOR/NAR1/NAR2 Buttons NOR NAR ModeNB Button 2nd and 3rd if Filter BandwidthTuner Button VRF IndicatorVRF/MEM CH Knob VRF/MEM CH Knob SequenceLCD Bargraph Meter Indications MEM F Sub Receiver ModeWait HI SWRTOP Panel Access & Controls Rtty PKT12. CW Additional NoteRemote Jack Rear Panel Controls & ConnectorsCW Sidetone Trimmer Packet DIN JackDC in Jack Band Data DIN JackKey Beeper OperationBefore Starting Menu ProgrammingMode Selection Special Note for CW Mode Reverse CW sidebandShuttle Jog VFO KnobFast Button Operation VRF/MEM CHPanel Up/Down Buttons Display SettingsMicrophone Up/Dwn Buttons VFO Channel SteppingToggle VFOs Alternate VFO Operation Front & RearevfoVFO Selection & Receiver Muting Keypad Frequency EntryRTTY/PKT Tuning Signal Tuning Meter IndicationsCW Tuning AM Synchronous Tuning SUB-DISPLAY Mode Selection Expanded Tuning ScaleAM Synchronous Tuning Meter Frequency Band Range MHz AM Broadcast ReceptionGeneral Coverage Reception Wide Band and Tuned Preamp Selection Receiver Front End Configuration For illustrative purposesDealing with Interference VRF Variable RF FRONT-END FilterAGC Automatic Gain Control Selection RF Gain SettingIPO Intercept Point Optimization If Filter Bandwidth Selection There are two banks of select Main receiver VFO-A if Bandwidth Filter SelectionNoise Blanker Width Control Width Action Using Width control to reduce QRMUsing if Shift to reduce QRM SHIFT/WIDTH Tuning StepsIf Shift Action Notch FilterClarifier RX/TX Offset Tuning Advice on QRM ReductionOffset Display Mode Clarifier SettingsAntenna Selection TransmittingBand TX Range Selecting AntennasSSB Transmission Important NoteTransmitter Monitor RF Speech Processor Microphone Tone SelectionClass-A Operation Carrier Point OffsetCW Transmission VOX Operation Voice-Actuated T/R Switching OperationStraight-Key Operation CW Straight Key and Paddle Connections Electronic Keyer OperationACS Auto Character Spacing CW Pitch Setting and Spot Tone Keyer SettingsRtty Operation Digital Mode OperationBaud Packet AM TransmissionTNC Tone Pair Tone Center Frequency Packet OperationBaud FM Packet FM Transmission FM Repeater OperationDual Reception Main and Sub VFO AudioHeadphone Audio Adjustments Using Headphones for Dual ReceiveSplit Frequency Operation Split Operation ModeSUB VFO-B Settings VFO Tracking Sideband Diversity ReceptionBandwidth Diversity Reception Memory Structure Memory FeaturesAuto Channel-Up Basic Memory Storage ProcedureRegarding the VRF/MEM CH Knob Memory ProgrammingMemory Checking Memory TuningRecalling & Operating on Memory Channels Copying Between Memories Limiting Memory Group OperationCopying a Selected Memory to VFO-A Grouping Memories QMB Quick Memory Bank Operation VFO Scanning Auto Memory WriteMemory Scanning Memory Scan SkipMemory Masking Scan Resume ModeScan Skip Disable Programmed Memory Scanning PMS Memories P1 ~ P9 Advanced Features Edsp Contours Edsp ModulationEdsp Functions Edsp RX Audio EnhancementEdsp Auto Multiple Notch Action Edsp Noise ReducerEdsp Auto Multiple Notch Filter Important Note About Edsp Remote Control Operation FeaturesIntroduction Contest Keyer ControlCQ or ID Memory Contest Number MemoryUser Message Memories 1 Message StorageContest Keyer Operation Tune ModeII. VFO/MEMORY Control III. Main VFO-A ControlOverview USER-CUSTOMIZED Operating ModeComments Sub VFO B Dial Main VFO a DialDVS-2 Controls Message Recording Message Recording PlaybackSegment No Function SegmentSelecting Receiver Audio Receiver Recording withMessage Transmission Message MonitorOperation Phone Patch OperationPacket Tuning Tuning Meter RE-CALIBRATIONOverview CAT Data Protocol CAT 5-BYTE Command StructureOpcode CAT Data Byte Format50 H 03 H 00 H 81 H 09 H Constructing and Sending CAT CommandsDATA/ARGUMENT Bytes 0A HDownloading Status Update Data OrganizationStatus Flags Bytes 1~ Memory Channel Data ByteStatus Flag Byte #4 Contents Status Flag Byte #1 ContentsStatus Flag Byte #2 Contents Status Flag Byte #5 ContentsMemory Channel Data Hex Codes Byte Data Record Structure Rtty PKT Coding Examples 0AH Opcode Command Chart0CH 0EH70H Command Parameter Bytes Opcode Or Key 1st 2rd 3rd 4th 5thEdsp 75H8AH RPTVFO 8CHByte Format F = 00H Byte Format F = 01H FAHGrP2-cH GrP1-cHGrP3-cH GrP4-cHEdSP Auto-uPDiAL-SPd SJ-SPEEdScAn-ALL Auto-inSc-dL-ti NotcHNot Used RF out SP-HoLdBEEP BEEP-FDAtAnAr2 CW norSub-FiL FiLNot Used CtcSS PAc-tonETonE SEt RPt-SHFtFASt-SEt Rc-FuncLock-SEL PA-cntSub-AGc USEr-SEtTunEr CAr oFSt1st Fc = F + 70.455 BFO kHz Custom Frequency & Display Offset InformationPKT-F User KHz 500 Hz 250 HzFunc No Function Setting Range Default Menu Selection Setting TableMONO/STEREO 1/STEREO Stereo Main VFO-A/SUB VFO-BSEPARATE/BALANCE Separate NORMAL/REVERSE NormalLSB USB CW USB CW LSB Rtty LSB Rtty USB PKT LSB Default User Function SettingsTX PLL Easy Set Mode SettingsRX PLL TCXO-6 Installation Installing Internal AccessoriesInstallation Filter InstallationMain Receiver 2ND and 3RD if Filters SUB Receiver CW Narrow FilterMemory BACK-UP Switch Lithium Battery ReplacementInternal 13.8V Fuse Replacement POWER-ON Microprocessor Reset Procedures MARK-V FT-1000MP Operating Manual