Vertex Standard FT-1000MP manual Operation with NON-QSK Amplifiers FL-2100SERIES or Others

Page 14

ACCESSORY INSTALLATION

LINEAR AMPLIFIER INTERFACING

If using an FL-7000, connect optional cable E-767(P/N D4000019) from the transceiver BAND DATA jack to the amplifier ACC-2jack. This provides automatic band selection for the linear, as well as QSK Tx/Rx switching control. Turn on the FL-7000rear panel ATT switch to activate the 3 dB input RF power attenuator, to pad the 200 Watt input power from the MARK-V FT- 1000MP.

If using another manufacturer’s QSK linear, and if its switching circuitry consumes less than 150 mA of DC voltage below 40 V, you can connect the Tx/Rx switching line for the linear to pin 2 (“TX GND”) of the BAND DATA jack (use pin 3 for ground), and the linear’s exciter-enable output to pin 8 (“TX INHIBIT”) of the BAND DATA jack. This line must be switched to ground to enable transmission once the linear is ready for ex- citation from the MARK-VFT-1000MP. If your QSK lin- ear sinks more than 100 mA or uses more than 15 V for T/R relay switching, you will have to provide a suit- able external interface transistor, controlled by pin 2. Be certain to make provision for suitable reduction of the drive power from the MARK-VFT-1000MP, so as not to damage your amplifier.

OPERATION WITH NON-QSK AMPLIFIERS (FL-2100SERIES OR OTHERS)

The TX GND jack on the transceiver rear panel is connected to an internal relay, for non-QSK T/R switch- ing of linear amplifiers that use AC switching voltage, or DC voltage greater than +15 V, negative DC voltage of any kind (such as the Heath® SB-220/SB-221 mod- els), or if they are required to sink more than 100 mA for T/R switching. A schematic diagram of the relay circuit is provided below. If not using your linear ampli- fier in a full break-in environment, the use of this relay for amplifier switching is highly recommended.

This relay comes disabled (rear-panel LIN set to “OFF”) to avoid the clicking sound when the transceiver is used alone or with a QSK linear. To enable the relay for non-QSK linears that exceed the above T/R switch- ing requirements, you will need to move the LIN switch, located in the hole near the center of the rear panel, to its right position (see the drawing). Use a thin, insu- lated, sharp object to move the switch. Then connect the center contact of the TX GND jack to the positive relay-control line to your linear, and the outer contact to the “common” line or the linear’s chassis ground. Refer to the diagram at the next page; in this example, a older non-QSK amplifier (FL-2100B) is shown.

With the relay now enabled, the MARK-V FT- 1000MP can support non-QSK linear T/R switching voltages up to 100 VAC @ 500 mA, or DC voltage up to 60 V @ 200 mA, or closed-circuit current up to 1 A with DC voltage up to 30 V.

page 12

MARK-V FT-1000MP Operating Manual

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Vertex Standard Yaesu Europe B.VTabel of Contents General Description MARK-V FT-1000MP Operating ManualMARK-V FT-1000MP Operating Manual Transmitter SpecificationsGeneral ReceiverPLUG/CONNECTOR Pinout Diagrams Accessories & Options Supplied AccessoriesOptional Sub Receiver Filter If Crystal Filter OptionsOptional Main Receiver Filters Available OptionsGround Connections Safety PrecautionsPower Connections RF Field Exposure Advisory & Electromagnetic Compatibility Antenna PrecautionsElectrical Shock Prevention Preliminary Inspection General Setup FP-29 Transceiver LocationAntenna Considerations Adjusting the Front FeetMemory Backup RG-8XQSK Accessory InstallationLinear Amplifier Interfacing Operation with QSK AmplifiersOperation with NON-QSK Amplifiers FL-2100SERIES or Others About ALC Transverter Operation Digital Modem TNC, WEATHERFAX, ETC. Interfacing Digital Modes with a TNC Or Computer Sound Card PSK-31MARK-V FT-1000MP TNC Accessory Installation Accessory Installation Other DIGITAL/RECORDING Device Interfacing FeaturesConfiguration Suggestions CW KEY/PADDLE and Computer Keying Interface SuggestionsLarge Receive Antennas Antenna ConnectionsPersonal Computer Interfacing for Contest SOFTWARE, ETC Front Panel Controls SUB AF Knob AF Gain RF Gain KnobRF PWR Knob Moni KnobCLASS-A Button Mode Selection ButtonsEdsp Filters Fast ButtonShuttle Jog and VRF & Idbt Buttons Main VFO-A Tuning KnobMain VFO-A RX & TX Switch-LED AF REV ButtonVFO & Memory Control Band KeypadSUB SQL Knob SUB VFO-B RX & TX Switch-LEDLock Button CW and Electronic Keyer ControlsNB Button NOR NAR ModeBandwidth Buttons NOR/NAR1/NAR2 Buttons 2nd and 3rd if Filter BandwidthVRF/MEM CH Knob VRF IndicatorTuner Button VRF/MEM CH Knob SequenceLCD Bargraph Meter Indications Wait Sub Receiver ModeMEM F HI SWRTOP Panel Access & Controls 12. CW PKTRtty Additional NoteCW Sidetone Trimmer Rear Panel Controls & ConnectorsRemote Jack Packet DIN JackBand Data DIN Jack DC in JackBefore Starting OperationKey Beeper Menu ProgrammingSpecial Note for CW Mode Reverse CW sideband Mode SelectionFast Button Operation VFO KnobShuttle Jog VRF/MEM CHMicrophone Up/Dwn Buttons Display SettingsPanel Up/Down Buttons VFO Channel SteppingVFO Selection & Receiver Muting Alternate VFO Operation Front & RearevfoToggle VFOs Keypad Frequency EntryRTTY/PKT Tuning Signal Tuning Meter IndicationsCW Tuning AM Synchronous Tuning SUB-DISPLAY Mode Selection Expanded Tuning ScaleAM Synchronous Tuning Meter Frequency Band Range MHz AM Broadcast ReceptionGeneral Coverage Reception Dealing with Interference Receiver Front End Configuration For illustrative purposesWide Band and Tuned Preamp Selection VRF Variable RF FRONT-END FilterAGC Automatic Gain Control Selection RF Gain SettingIPO Intercept Point Optimization If Filter Bandwidth Selection There are two banks of select Main receiver VFO-A if Bandwidth Filter SelectionNoise Blanker Width Action Using Width control to reduce QRM Width ControlIf Shift Action SHIFT/WIDTH Tuning StepsUsing if Shift to reduce QRM Notch FilterAdvice on QRM Reduction Clarifier RX/TX Offset TuningClarifier Settings Offset Display ModeBand TX Range TransmittingAntenna Selection Selecting AntennasSSB Transmission Important NoteTransmitter Monitor Class-A Operation Microphone Tone SelectionRF Speech Processor Carrier Point OffsetCW Transmission VOX Operation Voice-Actuated T/R Switching OperationStraight-Key Operation CW Straight Key and Paddle Connections Electronic Keyer OperationACS Auto Character Spacing Keyer Settings CW Pitch Setting and Spot ToneBaud Packet Digital Mode OperationRtty Operation AM TransmissionTNC Tone Pair Tone Center Frequency Packet OperationBaud FM Packet FM Repeater Operation FM TransmissionMain and Sub VFO Audio Dual ReceptionUsing Headphones for Dual Receive Headphone Audio AdjustmentsSplit Frequency Operation Split Operation ModeSUB VFO-B Settings VFO Tracking Sideband Diversity ReceptionBandwidth Diversity Reception Memory Features Memory StructureRegarding the VRF/MEM CH Knob Basic Memory Storage ProcedureAuto Channel-Up Memory ProgrammingMemory Checking Memory TuningRecalling & Operating on Memory Channels Copying Between Memories Limiting Memory Group OperationCopying a Selected Memory to VFO-A Grouping Memories QMB Quick Memory Bank Operation Memory Scanning Auto Memory WriteVFO Scanning Memory Scan SkipMemory Masking Scan Resume ModeScan Skip Disable Programmed Memory Scanning PMS Memories P1 ~ P9 Advanced Features Edsp Functions Edsp ModulationEdsp Contours Edsp RX Audio EnhancementEdsp Auto Multiple Notch Action Edsp Noise ReducerEdsp Auto Multiple Notch Filter Important Note About Edsp Introduction FeaturesRemote Control Operation Contest Keyer ControlUser Message Memories 1 Contest Number MemoryCQ or ID Memory Message StorageTune Mode Contest Keyer OperationIII. Main VFO-A Control II. VFO/MEMORY ControlComments USER-CUSTOMIZED Operating ModeOverview Sub VFO B Dial Main VFO a DialDVS-2 Controls Segment Message Recording PlaybackMessage Recording No Function SegmentMessage Transmission Receiver Recording withSelecting Receiver Audio Message MonitorPhone Patch Operation OperationTuning Meter RE-CALIBRATION Packet TuningOpcode CAT 5-BYTE Command StructureOverview CAT Data Protocol CAT Data Byte FormatDATA/ARGUMENT Bytes Constructing and Sending CAT Commands50 H 03 H 00 H 81 H 09 H 0A HStatus Flags Bytes 1~ Status Update Data OrganizationDownloading Memory Channel Data ByteStatus Flag Byte #2 Contents Status Flag Byte #1 ContentsStatus Flag Byte #4 Contents Status Flag Byte #5 ContentsMemory Channel Data Hex Codes Byte Data Record Structure Rtty PKT Coding Examples 0CH Opcode Command Chart0AH 0EHEdsp Command Parameter Bytes Opcode Or Key 1st 2rd 3rd 4th 5th70H 75HVFO RPT8AH 8CHFAH Byte Format F = 00H Byte Format F = 01HGrP3-cH GrP1-cHGrP2-cH GrP4-cHDiAL-SPd Auto-uPEdSP SJ-SPEEdSc-dL-ti Auto-inScAn-ALL NotcHBEEP SP-HoLdNot Used RF out BEEP-FSub-FiL CW norDAtAnAr2 FiLTonE SEt PAc-tonENot Used CtcSS RPt-SHFtLock-SEL Rc-FuncFASt-SEt PA-cntTunEr USEr-SEtSub-AGc CAr oFStCustom Frequency & Display Offset Information 1st Fc = F + 70.455 BFO kHzKHz 500 Hz 250 Hz PKT-F UserMenu Selection Setting Table Func No Function Setting Range DefaultSEPARATE/BALANCE Separate Main VFO-A/SUB VFO-BMONO/STEREO 1/STEREO Stereo NORMAL/REVERSE NormalDefault User Function Settings LSB USB CW USB CW LSB Rtty LSB Rtty USB PKT LSBTX PLL Easy Set Mode SettingsRX PLL Installing Internal Accessories TCXO-6 InstallationMain Receiver 2ND and 3RD if Filters Filter InstallationInstallation SUB Receiver CW Narrow FilterMemory BACK-UP Switch Lithium Battery ReplacementInternal 13.8V Fuse Replacement POWER-ON Microprocessor Reset Procedures MARK-V FT-1000MP Operating Manual
Top Page Image Contents