Vertex Standard FT-1000MP manual Accessories & Options, Supplied Accessories

Page 7

ACCESSORIES & OPTIONS

SUPPLIED ACCESSORIES

 

AC Power Supply FP-29and its accessories (Separate Carton)

1

Hand Microphone MH-31B8(depending on transceiver version)

1

RCA Plug (P0090544)

1

¼-inch 3-contact Plug (P0090008)

1

3.5 mm 2-contact Plug (P0090034)

1

3.5 mm 3-contact Plug (P0091046)

1

4-pin DIN Plug (P0091004)

1

5-pin DIN Plug (P0091006)

1

Operating Manual

1

Warranty Card

1

MARK-V FT-1000MP Operating Manual

page 5

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Yaesu Europe B.V Vertex StandardTabel of Contents MARK-V FT-1000MP Operating Manual General DescriptionMARK-V FT-1000MP Operating Manual Receiver SpecificationsGeneral TransmitterPLUG/CONNECTOR Pinout Diagrams Supplied Accessories Accessories & OptionsAvailable Options If Crystal Filter OptionsOptional Main Receiver Filters Optional Sub Receiver FilterPower Connections Safety PrecautionsGround Connections Electrical Shock Prevention Antenna PrecautionsRF Field Exposure Advisory & Electromagnetic Compatibility Transceiver Location General SetupFP-29 Preliminary InspectionRG-8X Adjusting the Front FeetMemory Backup Antenna ConsiderationsOperation with QSK Amplifiers Accessory InstallationLinear Amplifier Interfacing QSKOperation with NON-QSK Amplifiers FL-2100SERIES or Others About ALC Transverter Operation Digital Modes with a TNC Or Computer Sound Card PSK-31 Digital Modem TNC, WEATHERFAX, ETC. InterfacingMARK-V FT-1000MP TNC Accessory Installation Accessory Installation CW KEY/PADDLE and Computer Keying Interface Suggestions FeaturesConfiguration Suggestions Other DIGITAL/RECORDING Device InterfacingAntenna Connections Large Receive AntennasPersonal Computer Interfacing for Contest SOFTWARE, ETC Front Panel Controls Moni Knob AF Gain RF Gain KnobRF PWR Knob SUB AF KnobFast Button Mode Selection ButtonsEdsp Filters CLASS-A ButtonAF REV Button Main VFO-A Tuning KnobMain VFO-A RX & TX Switch-LED Shuttle Jog and VRF & Idbt ButtonsBand Keypad VFO & Memory ControlCW and Electronic Keyer Controls SUB VFO-B RX & TX Switch-LEDLock Button SUB SQL Knob2nd and 3rd if Filter Bandwidth NOR NAR ModeBandwidth Buttons NOR/NAR1/NAR2 Buttons NB ButtonVRF/MEM CH Knob Sequence VRF IndicatorTuner Button VRF/MEM CH KnobLCD Bargraph Meter Indications HI SWR Sub Receiver ModeMEM F WaitTOP Panel Access & Controls Additional Note PKTRtty 12. CWPacket DIN Jack Rear Panel Controls & ConnectorsRemote Jack CW Sidetone TrimmerDC in Jack Band Data DIN JackMenu Programming OperationKey Beeper Before StartingMode Selection Special Note for CW Mode Reverse CW sidebandVRF/MEM CH VFO KnobShuttle Jog Fast Button OperationVFO Channel Stepping Display SettingsPanel Up/Down Buttons Microphone Up/Dwn ButtonsKeypad Frequency Entry Alternate VFO Operation Front & RearevfoToggle VFOs VFO Selection & Receiver MutingCW Tuning Signal Tuning Meter IndicationsRTTY/PKT Tuning AM Synchronous Tuning Expanded Tuning ScaleAM Synchronous Tuning SUB-DISPLAY Mode Selection General Coverage Reception AM Broadcast ReceptionMeter Frequency Band Range MHz VRF Variable RF FRONT-END Filter Receiver Front End Configuration For illustrative purposesWide Band and Tuned Preamp Selection Dealing with InterferenceIPO Intercept Point Optimization RF Gain SettingAGC Automatic Gain Control Selection Noise Blanker Main receiver VFO-A if Bandwidth Filter SelectionIf Filter Bandwidth Selection There are two banks of select Width Control Width Action Using Width control to reduce QRMNotch Filter SHIFT/WIDTH Tuning StepsUsing if Shift to reduce QRM If Shift ActionClarifier RX/TX Offset Tuning Advice on QRM ReductionOffset Display Mode Clarifier SettingsSelecting Antennas TransmittingAntenna Selection Band TX RangeTransmitter Monitor Important NoteSSB Transmission Carrier Point Offset Microphone Tone SelectionRF Speech Processor Class-A OperationStraight-Key Operation VOX Operation Voice-Actuated T/R Switching OperationCW Transmission ACS Auto Character Spacing Electronic Keyer OperationCW Straight Key and Paddle Connections CW Pitch Setting and Spot Tone Keyer SettingsAM Transmission Digital Mode OperationRtty Operation Baud PacketBaud FM Packet Packet OperationTNC Tone Pair Tone Center Frequency FM Transmission FM Repeater OperationDual Reception Main and Sub VFO AudioHeadphone Audio Adjustments Using Headphones for Dual ReceiveSUB VFO-B Settings Split Operation ModeSplit Frequency Operation Bandwidth Diversity Reception Sideband Diversity ReceptionVFO Tracking Memory Structure Memory FeaturesMemory Programming Basic Memory Storage ProcedureAuto Channel-Up Regarding the VRF/MEM CH KnobRecalling & Operating on Memory Channels Memory TuningMemory Checking Copying a Selected Memory to VFO-A Grouping Memories Limiting Memory Group OperationCopying Between Memories QMB Quick Memory Bank Operation Memory Scan Skip Auto Memory WriteVFO Scanning Memory ScanningScan Skip Disable Scan Resume ModeMemory Masking Programmed Memory Scanning PMS Memories P1 ~ P9 Advanced Features Edsp RX Audio Enhancement Edsp ModulationEdsp Contours Edsp FunctionsEdsp Auto Multiple Notch Filter Edsp Noise ReducerEdsp Auto Multiple Notch Action Important Note About Edsp Contest Keyer Control FeaturesRemote Control Operation IntroductionMessage Storage Contest Number MemoryCQ or ID Memory User Message Memories 1Contest Keyer Operation Tune ModeII. VFO/MEMORY Control III. Main VFO-A ControlSub VFO B Dial Main VFO a Dial USER-CUSTOMIZED Operating ModeOverview CommentsDVS-2 Controls No Function Segment Message Recording PlaybackMessage Recording SegmentMessage Monitor Receiver Recording withSelecting Receiver Audio Message TransmissionOperation Phone Patch OperationPacket Tuning Tuning Meter RE-CALIBRATIONCAT Data Byte Format CAT 5-BYTE Command StructureOverview CAT Data Protocol Opcode0A H Constructing and Sending CAT Commands50 H 03 H 00 H 81 H 09 H DATA/ARGUMENT BytesMemory Channel Data Byte Status Update Data OrganizationDownloading Status Flags Bytes 1~Status Flag Byte #5 Contents Status Flag Byte #1 ContentsStatus Flag Byte #4 Contents Status Flag Byte #2 ContentsMemory Channel Data Hex Codes Byte Data Record Structure Rtty PKT Coding Examples 0EH Opcode Command Chart0AH 0CH75H Command Parameter Bytes Opcode Or Key 1st 2rd 3rd 4th 5th70H Edsp8CH RPT8AH VFOByte Format F = 00H Byte Format F = 01H FAHGrP4-cH GrP1-cHGrP2-cH GrP3-cHSJ-SPEEd Auto-uPEdSP DiAL-SPdNotcH Auto-inScAn-ALL Sc-dL-tiBEEP-F SP-HoLdNot Used RF out BEEPFiL CW norDAtAnAr2 Sub-FiLRPt-SHFt PAc-tonENot Used CtcSS TonE SEtPA-cnt Rc-FuncFASt-SEt Lock-SELCAr oFSt USEr-SEtSub-AGc TunEr1st Fc = F + 70.455 BFO kHz Custom Frequency & Display Offset InformationPKT-F User KHz 500 Hz 250 HzFunc No Function Setting Range Default Menu Selection Setting TableNORMAL/REVERSE Normal Main VFO-A/SUB VFO-BMONO/STEREO 1/STEREO Stereo SEPARATE/BALANCE SeparateLSB USB CW USB CW LSB Rtty LSB Rtty USB PKT LSB Default User Function SettingsRX PLL Easy Set Mode SettingsTX PLL TCXO-6 Installation Installing Internal AccessoriesSUB Receiver CW Narrow Filter Filter InstallationInstallation Main Receiver 2ND and 3RD if FiltersInternal 13.8V Fuse Replacement Lithium Battery ReplacementMemory BACK-UP Switch POWER-ON Microprocessor Reset Procedures MARK-V FT-1000MP Operating Manual
Top Page Image Contents