Vertex Standard FT-1000MP manual FM Repeater Operation, FM Transmission

Page 61

OPERATION

TRANSMITTING

FM TRANSMISSION

A separate, dedicated “29 MHz” band is provided on the MARK-VFT-1000MP, allowing you to operate both on 28 MHz in narrow-band modes, and above 29 MHz using narrow-band FM. This relieves you of the need to change all your configurations when switching voice modes.

For transmission, the only control on the front panel you need be concerned about is RF PWR. Microphone gain for FM is set via the separate FM MIC control in the top access panel, and normally needs no adjust- ment after leaving the factory. If you receive signals reports of low audio with a strong carrier, you may want to increase the gain. If you notice distortion in the trans- mit monitor, you may want to decrease it. Otherwise, we suggest leaving it alone. Remember that the ap- parent modulation level on 29 MHz will be less than you are accustomed to on VHF, due to international regulations restricting the maximum deviation to ±2.5 kHz.

All you need to do for most operation is set the METER selector to the “PO” position, and adjust the RF PWR control for the desired output while transmit- ting. If you need full power, keep your transmissions to three minutes or less, with the same time for recep- tion. Otherwise, set the power output to 100 Watts or less, and you should never encounter any duty cycle limitations.

You can use the VOX circuit for t/r switching, if de- sired, and the transmit monitor to listen to your signal. See also the FM Repeater Operation at the right.

FM Repeater Operation

Several features are available for operation on FM repeaters above 29 MHz, which typically use 100-kHz splits.

To locate these repeaters, you can ask around the calling channel (29.6 MHz), or you may want to load a block of memory channels (see page 67) with 50-kHz frequency multiples from 29.61 to 29.7 MHz (and FM mode, of course). Then set the squelch so that the receiver is silent on a clear channel, and hold the mi- crophone UP/DWN keys to scan the memories.

Repeater Shift - When you find a repeater, press the [RPT] button, once for shift (to transmit 100 kHz below your receiving frequency). Pressing it again will select “+” shift, but this is not used above 29.6 MHz. Press it once more to re- turn to simplex. Try a quick identification transmission to make sure you have the shift right.

Repeater TX Offset - For repeaters not using the standard 100 kHz offfset, you can change the default offset between 0 ~ 200 kHz via menu selection 6-9.

CTCSS Tone - A low-level 88.5-Hz subaudible tone is transmitted to access closed repeaters. Should a different CTCSS tone be required, you can choose any one of 33 standard tones via menu selection 6-7.

Tone Type – Continuous (CTCSS) or burst tone transmission is enabled from menu selection 6-8.

CTCSS TONE FREQUENCIES

67.0

Hz

118.8 Hz

173.8 Hz

71.9

Hz

123.0 Hz

179.9 Hz

 

 

 

 

77.0

Hz

127.3 Hz

186.2 Hz

 

 

 

 

82.5

Hz

131.8 Hz

192.8 Hz

 

 

 

 

88.5

Hz

136.5 Hz

203.5 Hz

 

 

 

 

94.8

Hz

141.3 Hz

210.7 Hz

 

 

 

100.0 Hz

146.2 Hz

218.1 Hz

 

 

 

103.5 Hz

151.4 Hz

225.7 Hz

 

 

 

107.2 Hz

156.7 Hz

233.6 Hz

 

 

 

 

110.9

Hz

162.2 Hz

241.8 Hz

 

 

 

 

114.8

Hz

167.9 Hz

250.3 Hz

MARK-V FT-1000MP Operating Manual

page 59

Image 61
Contents Yaesu Europe B.V Vertex StandardTabel of Contents MARK-V FT-1000MP Operating Manual General DescriptionMARK-V FT-1000MP Operating Manual General SpecificationsTransmitter ReceiverPLUG/CONNECTOR Pinout Diagrams Supplied Accessories Accessories & OptionsOptional Main Receiver Filters If Crystal Filter OptionsOptional Sub Receiver Filter Available OptionsPower Connections Safety PrecautionsGround Connections Electrical Shock Prevention Antenna PrecautionsRF Field Exposure Advisory & Electromagnetic Compatibility FP-29 General SetupPreliminary Inspection Transceiver LocationMemory Backup Adjusting the Front FeetAntenna Considerations RG-8XLinear Amplifier Interfacing Accessory InstallationQSK Operation with QSK AmplifiersOperation with NON-QSK Amplifiers FL-2100SERIES or Others About ALC Transverter Operation Digital Modes with a TNC Or Computer Sound Card PSK-31 Digital Modem TNC, WEATHERFAX, ETC. InterfacingMARK-V FT-1000MP TNC Accessory Installation Accessory Installation Configuration Suggestions FeaturesOther DIGITAL/RECORDING Device Interfacing CW KEY/PADDLE and Computer Keying Interface SuggestionsAntenna Connections Large Receive AntennasPersonal Computer Interfacing for Contest SOFTWARE, ETC Front Panel Controls RF PWR Knob AF Gain RF Gain KnobSUB AF Knob Moni KnobEdsp Filters Mode Selection ButtonsCLASS-A Button Fast ButtonMain VFO-A RX & TX Switch-LED Main VFO-A Tuning KnobShuttle Jog and VRF & Idbt Buttons AF REV ButtonBand Keypad VFO & Memory ControlLock Button SUB VFO-B RX & TX Switch-LEDSUB SQL Knob CW and Electronic Keyer ControlsBandwidth Buttons NOR/NAR1/NAR2 Buttons NOR NAR ModeNB Button 2nd and 3rd if Filter BandwidthTuner Button VRF IndicatorVRF/MEM CH Knob VRF/MEM CH Knob SequenceLCD Bargraph Meter Indications MEM F Sub Receiver ModeWait HI SWRTOP Panel Access & Controls Rtty PKT12. CW Additional NoteRemote Jack Rear Panel Controls & ConnectorsCW Sidetone Trimmer Packet DIN JackDC in Jack Band Data DIN JackKey Beeper OperationBefore Starting Menu ProgrammingMode Selection Special Note for CW Mode Reverse CW sidebandShuttle Jog VFO KnobFast Button Operation VRF/MEM CHPanel Up/Down Buttons Display SettingsMicrophone Up/Dwn Buttons VFO Channel SteppingToggle VFOs Alternate VFO Operation Front & RearevfoVFO Selection & Receiver Muting Keypad Frequency EntryCW Tuning Signal Tuning Meter IndicationsRTTY/PKT Tuning AM Synchronous Tuning Expanded Tuning ScaleAM Synchronous Tuning SUB-DISPLAY Mode Selection General Coverage Reception AM Broadcast ReceptionMeter Frequency Band Range MHz Wide Band and Tuned Preamp Selection Receiver Front End Configuration For illustrative purposesDealing with Interference VRF Variable RF FRONT-END FilterIPO Intercept Point Optimization RF Gain SettingAGC Automatic Gain Control Selection Noise Blanker Main receiver VFO-A if Bandwidth Filter SelectionIf Filter Bandwidth Selection There are two banks of select Width Control Width Action Using Width control to reduce QRMUsing if Shift to reduce QRM SHIFT/WIDTH Tuning StepsIf Shift Action Notch FilterClarifier RX/TX Offset Tuning Advice on QRM ReductionOffset Display Mode Clarifier SettingsAntenna Selection TransmittingBand TX Range Selecting AntennasTransmitter Monitor Important NoteSSB Transmission RF Speech Processor Microphone Tone SelectionClass-A Operation Carrier Point OffsetStraight-Key Operation VOX Operation Voice-Actuated T/R Switching OperationCW Transmission ACS Auto Character Spacing Electronic Keyer OperationCW Straight Key and Paddle Connections CW Pitch Setting and Spot Tone Keyer SettingsRtty Operation Digital Mode OperationBaud Packet AM TransmissionBaud FM Packet Packet OperationTNC Tone Pair Tone Center Frequency FM Transmission FM Repeater OperationDual Reception Main and Sub VFO AudioHeadphone Audio Adjustments Using Headphones for Dual ReceiveSUB VFO-B Settings Split Operation ModeSplit Frequency Operation Bandwidth Diversity Reception Sideband Diversity ReceptionVFO Tracking Memory Structure Memory FeaturesAuto Channel-Up Basic Memory Storage ProcedureRegarding the VRF/MEM CH Knob Memory ProgrammingRecalling & Operating on Memory Channels Memory TuningMemory Checking Copying a Selected Memory to VFO-A Grouping Memories Limiting Memory Group OperationCopying Between Memories QMB Quick Memory Bank Operation VFO Scanning Auto Memory WriteMemory Scanning Memory Scan SkipScan Skip Disable Scan Resume ModeMemory Masking Programmed Memory Scanning PMS Memories P1 ~ P9 Advanced Features Edsp Contours Edsp ModulationEdsp Functions Edsp RX Audio EnhancementEdsp Auto Multiple Notch Filter Edsp Noise ReducerEdsp Auto Multiple Notch Action Important Note About Edsp Remote Control Operation FeaturesIntroduction Contest Keyer ControlCQ or ID Memory Contest Number MemoryUser Message Memories 1 Message StorageContest Keyer Operation Tune ModeII. VFO/MEMORY Control III. Main VFO-A ControlOverview USER-CUSTOMIZED Operating ModeComments Sub VFO B Dial Main VFO a DialDVS-2 Controls Message Recording Message Recording PlaybackSegment No Function SegmentSelecting Receiver Audio Receiver Recording withMessage Transmission Message MonitorOperation Phone Patch OperationPacket Tuning Tuning Meter RE-CALIBRATIONOverview CAT Data Protocol CAT 5-BYTE Command StructureOpcode CAT Data Byte Format50 H 03 H 00 H 81 H 09 H Constructing and Sending CAT CommandsDATA/ARGUMENT Bytes 0A HDownloading Status Update Data OrganizationStatus Flags Bytes 1~ Memory Channel Data ByteStatus Flag Byte #4 Contents Status Flag Byte #1 ContentsStatus Flag Byte #2 Contents Status Flag Byte #5 ContentsMemory Channel Data Hex Codes Byte Data Record Structure Rtty PKT Coding Examples 0AH Opcode Command Chart0CH 0EH70H Command Parameter Bytes Opcode Or Key 1st 2rd 3rd 4th 5thEdsp 75H8AH RPTVFO 8CHByte Format F = 00H Byte Format F = 01H FAHGrP2-cH GrP1-cHGrP3-cH GrP4-cHEdSP Auto-uPDiAL-SPd SJ-SPEEdScAn-ALL Auto-inSc-dL-ti NotcHNot Used RF out SP-HoLdBEEP BEEP-FDAtAnAr2 CW norSub-FiL FiLNot Used CtcSS PAc-tonETonE SEt RPt-SHFtFASt-SEt Rc-FuncLock-SEL PA-cntSub-AGc USEr-SEtTunEr CAr oFSt1st Fc = F + 70.455 BFO kHz Custom Frequency & Display Offset InformationPKT-F User KHz 500 Hz 250 HzFunc No Function Setting Range Default Menu Selection Setting TableMONO/STEREO 1/STEREO Stereo Main VFO-A/SUB VFO-BSEPARATE/BALANCE Separate NORMAL/REVERSE NormalLSB USB CW USB CW LSB Rtty LSB Rtty USB PKT LSB Default User Function SettingsRX PLL Easy Set Mode SettingsTX PLL TCXO-6 Installation Installing Internal AccessoriesInstallation Filter InstallationMain Receiver 2ND and 3RD if Filters SUB Receiver CW Narrow FilterInternal 13.8V Fuse Replacement Lithium Battery ReplacementMemory BACK-UP Switch POWER-ON Microprocessor Reset Procedures MARK-V FT-1000MP Operating Manual