Ericsson LBI-38823D manual Lock, Available on System Model radios only, Rcl, Indicators

Page 11

LOCK	The LOCK key in combination with the SHIFT/CLR
	key is used to lock the key pad. All buttons and keys
	will be locked except the VOLUME, PTT, HOME/E,
	SHIFT/CLR and the LOCK (shifted 0). This key is
	available on System Model radios only.
RCL	The RCL (Recall) key (shifted #) can be used to
	recall manually entered individual and interconnect
	calls in the EDACS and GE-MARC systems. This
	key is available on System Model radios and is
	active with trunked systems only.
INDICATORS

The 4-digit LIQUID CRYSTAL DISPLAY (LCD) uses the two digits on the left side to indicate the System number and the two digits on the right side to indicate the Group/Channel number. In addition there are 9 status indicators that are described on the following pages.

The LCD backlighting can be programmed to turn on anytime a button or key is pressed. It will remain on for a programmable length of time after the button or key is released. Backlighting is programmed on a per Group/Channel basis or it may be programmed to remain off at all times. Each radio that is programmed with backlighting may also be programmed to remain on or off when the PTT bar is pressed.

Figure 5 - Dual Format PCS™ Display

11

Image 11

Contents Ericssonz Page Table of Contents Keypad Lock System Model Only Dynamic Regrouping OptionalEmergency Operation Optional Introduction Dual Format PCS Radio Scan Model Dual Format PCS Radio System Model PTT Button Switch Description Controls ON/OFFScan Model Keypad STO HOME/ESPC SCAN-A/DRCL IndicatorsLock Available on System Model radios onlyBSY System And Group/Channel IndicatorsStatus Indicators SCN Radio is in the Program modeTurn on Alert Tones Standard Tones Power-UpLow Battery Carrier Control TimerSystem Busy Call ReceivedCall Queued Edacs Only Autokey Edacs OnlyIntrinsically Safe Usage Error MessagesOut Of Range/System Inoperative Pictured on Options and AccessoriesOption # Description Options And Accessories Installing the Battery Pack Battery PacksBattery Packs FM Approved Charging the Battery Packs Removing the Battery PackInstalling the Battery Pack Swivel Mount Removal and Replacement Rechargeable Battery Pack DisposalSwivel Mount Removal And Replacement Operating Tips Operating ProceduresWhen using two-way radios, remember the following rules Page NICKEL-CADMIUM Battery Warranty Current System selected Receiving a MessageSending a Message Using the Volume buttons, adjust the volume as necessarySquelch Adjustment Scan Model Radio Press and hold the SHFT/CLR buttonSending a Special Call Sending a Manually Entered Individual Call System Model RadioPage Sending a Manually Entered Interconnect Call Storing Individual And Interconnect Numbers Enter the desired storage location number Edacs Special Call Flowchart Wide Area And Priority System Scanning Optional Enable/Disable ScanScan Operation Add/Delete GroupsDtmf Overdial ProSoundDynamic Regrouping Optional Emergency Operation Optional Receiving An Emergency Call To enable an Emergency transmissionPressing the PTT bar to send the tones HOME/EMERGENCY KEY DefinitionKeypad Lock System Model Only HomePage GE-MARC Operation Sending a Message Sending a Special Call Sending a Preprogrammed Special Call In Conference Call Sending a Manually Entered Individual Call Sending a Manually Entered Interconnect Call Page Storing Individual And Interconnect Numbers Page Number will be displayed GE-MARC Special Call Flowchart Receiving a Message Direct ModeWide Area System Scan Sending a Message Add/Delete Channels Sending a Manually Entered Interconnect CallTo delete Channels from the scan list Scan must be disabled to add a channel to the scan listThis page intentionally left blank Conventional Mode Operation Sending a Message After all the digits have been keyed in, release the PTT bar Page Frequency Band OPERATOR’S Name Emergency Group System System Number Name TRK/CNV GRP/CHN GRP/CHN USE Warranty Emergency Numbers