Friedrich SH15, SH20 operation manual Section a a, Section B B

Page 12

920-024-05 (12-04)

Figure G

"J" TYPE SPEED NUT (ITEM #9)

2 REQUIRED

CUT WINGBOARD PANEL

SPRING STEEL CLIP (ITEM #10)

2 REQUIRED

CUT EDGE

SLIDE CLIP OVER CUT EDGE OF WINGBOARD PANEL

CENTER THE HOLE IN THE SPEED NUT OVER

THE SLOT IN THE WINGBOARD PANEL

STEP 5 ASSEMBLE CLIPS TO WINGBOARD PANELS: Assemble "J" type speed nuts (Item #9) and spring steel clips (Item #10) to the edges of the cut wingboard panels (See Figure G).

Figure H

SECURE THE SIDE WINGBOARD PANELS TO THE SIDE ANGLES WITH FOUR (4) #8 X 1/2" LONG SCREWS (ITEM #11), TWO ON EACH SIDE.

TOP OF CABINET

PLACE WINGBOARD PANEL IN WINDOW JAM TO COMPRESS THE SPRINGS INSIDE THE RUNNERS, AND SWING THE PANEL INTO PLACE INDICATED BY THE DOTTED LINE.

WINDOW JAM

SECTION A - A

STEP 6 INSTALL SIDE WINGBOARD PANELS: Be sure that the cabinet has been secured to the window sill and the outside support brackets have been installed as shown in Figures D and E on Page 11. Raise the window sash and install the right and left side wingboard panels (See Figure H).

STEP 7 INSTALL WINDOW SEALING GASKETS: Measure and cut the vinyl window seal gasket (grey color, Item #12) to fit the width of the window and install as shown in Figure I. Pull the window sash down behind the gasket. Measure and cut the dark foam window seal gasket (Item #13) and install it between the upper glass panel and the top part of the lower sash (See Figure I).

Figure I

VINYL WINDOW SEAL GASKET ITEM #12)

FOAM WINDOW SEAL GASKET (ITEM # 13)

LOWER WINDOW SASH

VINYL WINDOW SEAL GASKET

TOP WINGBOARD ANGLE

SECTION B - B

NOTE: FOR REASONS OF SECURITY AND SAFETY, THE CUSTOMER MUST PROVIDE A MEANS OF PREVENTING THE WINDOW FROM OPENING.

STEP 8 When possible, caulk the outside of the installation with industrial type caulking to prevent air and water leaks.

12

Image 12
Contents Hazardous Duty Room Air Conditioner Volt SH15 SH20Table of Contents Clean the filter frequently See General Maintenance Maintenance Checklist Filter InformationHazardgard Special Features Function Control PowerTemperature Control Control PanelModels SH15 and SH20 Electrical Requirements GroupsHazardgard Window Mount Installation Hardware Accessory DetailChassis Wiring and Preparation Unpacking The UnitProvided Hardware Shell Cabinet Preparation BeforeShell Installation Sash Window Installations Shell Cabinet Installation Standard Sash WindowsTypical Installation Sill Plate Section a a Section B BShell Installation Through-the-wall Installations Wall PreparationSpecial Instructions For Extra Thick Walls Hole Size RequirementsFrame Wall Construction Brick Veneer ConstructionSolid Masonry Typical Installation Screw #12A X 2 LongChassis Installation StepDetail Hazardgard Room AIR Conditioners Limited Warranty Instrucciones de Instalacion y Funcionamiento Tabla De Contenidos Instrucciones Para Uso Y MantenimientoInstrucciones Para La Instalacion Instrucciones Generales Informacion Sobre El Filtro Lista De Control Para El MantenimientoCaracteristicas Especiales Del Hazardgard Panel De ControlControl De Encendido Electricidad Control De La Temperatura¡Exclusiva Modelos SH15 y SH20 Requerimientos ElectricosGrupos Tamaño DEL Gabinete Lista DE Accesorios Número Descripción Cantidad De itemDesempaque de la unidad Preparacion y Instalacion Electrica Del ChasisHerramienta QUE SE Suministra Si la instalacion se hace a traves de la pared AntesdespuesFigura D Instalacion Tipica Del Filo Del Antepecho Figura G Dimension Chasis Terminada Pequeño Mediano Nota Estas SON LAS Dimensiones DEL Hueco TerminadoPreparacion De La Pared Instrucciones Especiales Para Paredes Extra GruesasConstruccion EN EL Marco DE LA ParedConstruccion EN Paredes DE LadrilloInstalacion Tipica Instalacion Del Chasis PasoFigura Q DetallePage Instructions d’installation et d’utilisation Instructions D’installation Table Des Matières920-024-05 Dépannage Panneau De Commande Commande De Fonction Mise En MarcheCommande De Température Caractéristiques Spéciales Des Appareils HazardgardExclusivité Modèles SH 15 et SH Alimentation ÉlectriqueGroupes Détail DES Accessoires Déballage De L’appareil Branchement Du Châssis Et PréparationQuincaillerie Fournie Installation dans une fenêtre à guillotine Installation à travers un murPréparation De L’enveloppe Avant AprèsInstallation de l’enveloppe fenêtre à guillotine standard Patte DE Support RÉFInstallation Typique De La Plaque De Seuil Coupe B B Installation De Lenveloppe Installation À Travers Un Mur Dimensions Finies DE L’OUVERTUREPréparation Du Mur Construction Avec UN Cadre EN Bois Construction AvecInstallation Typique Boulon DE ScellementInstallation Du Châssis Détail Garantie Limite DUN AN Climatiseurs Hazardgard Friedrich
Related manuals
Manual 60 pages 10.39 Kb Manual 60 pages 9.21 Kb

SH20, SH15 specifications

The Friedrich SH15 and SH20 models are exemplary representatives of advanced heating solutions, designed to address the diverse needs in residential and commercial environments. Engineered with a focus on efficiency, performance, and user-friendliness, these heating systems make a strong case for modern heating technology.

One of the standout features of both the SH15 and SH20 is their energy efficiency. These models utilize state-of-the-art heat pump technology, which allows them to extract heat from the environment even in colder temperatures. This results in significantly lower energy consumption compared to traditional heating systems, leading to reduced utility bills and a lower carbon footprint. The SH15 is designed for smaller spaces, while the SH20 offers a bit more power, making it suitable for larger areas or homes with greater heating demands.

Both models incorporate advanced inverter technology, which adjusts the compressor speed depending on the heating requirements. This ensures that the units operate at optimal efficiency, providing consistent temperature control while minimizing energy waste. Inverter-driven systems contribute to quieter operation as well, which is ideal for residential settings where noise can be a concern.

User-friendliness is another hallmark of the Friedrich SH15 and SH20. Equipped with intuitive digital controls, users can easily set their preferred temperatures and schedules, allowing for personalized comfort. Moreover, both models support smart home integration, enabling remote access and control through mobile applications. This feature not only enhances convenience but also allows users to monitor energy usage and make adjustments on the fly.

Durability is a key characteristic of these heating systems. Constructed with high-quality materials, the SH15 and SH20 are designed to withstand harsh environmental conditions, ensuring long-lasting performance. They also feature advanced air filtration systems that improve indoor air quality by effectively removing allergens and other pollutants.

In summary, the Friedrich SH15 and SH20 embody the cutting-edge of heating technology, offering powerful, efficient, and user-friendly solutions for diverse heating needs. With their advanced features, smart technology integration, and robust construction, these models are well-suited for modern living, ensuring comfortable and environmentally responsible heating year-round.