Friedrich SH20, SH15 Shell Installation Through-the-wall Installations, Wall Preparation

Page 13

920-024-05 (12-04)

Shell Installation: Through-the-wall Installations

Wall Preparation

The maximum wall thickness permissible without special construction is determined by the model size to be installed. THE OUT-

SIDE CABINET CONDENSER AIR INTAKE LOUVERS MUST NOT BE BLOCKED BY EXTENDING INSIDE THE WALL AREA. Observe the maximum wall thickness shown as dimension "A" in Figure J.

Special Instructions For Extra Thick Walls

For installation in walls exceeding the maximum thickness shown as dimension A, the following suggested construction may apply. (See Figure J).

Figure J

EXTRA THICK WALL CONSTRUCTION

15 1/8 " (384 MM)

MAXIMUM WALL THICKNESS

CONDENSER

AIR INTAKE

LOUVERS

TOP VIEW SHOWING BEVELED SIDES FOR AIR INTAKE. WALL BELOW UNIT MUST ALSO BE BEVELED TO ASSURE PROPER TILT ANGLE.

2" (51 MM) MINIMUM BOTH SIDES

CONDENSER AIR INTAKE LOUVERS

STEP 1 CHECKING WIRING AND PLUMBING: Check all wiring and plumbing inside and outside the wall to be sure none will be broken where the hole is to be cut.

STEP 2 HOLE CONSTRUCTION: Depending on the size of the unit to be installed, layout the hole dimensions in accordance with the chart below (See Figure K). Cut and frame in the hole to the finished dimensions. Use

2" x 4" material for framing and follow the suggested typical installations in Figure L, M or N on Page 15.

NOTE: IF THE WALL CONSTRUCTION IS TYPICAL FRAME OR 2 X 4 STUDDING WITH BRICK OR STONE VENEERS, LOCATE THE HOLE NEXT TO ONE OF THE STUDS. FOR MASONRY, CONCRETE OR CINDER BLOCK WALLS, LOCATE THE HOLE FOR CONVENIENCE.

Figure K

HOLE SIZE REQUIREMENTS

 

 

 

 

 

 

FINISHED

SMALL

MEDIUM

 

DIMENSION

CHASSIS

CHASSIS

 

 

 

 

 

A

16-3/16"

18-3/16"

 

 

 

 

 

B

26-3/16"

26-3/16"

 

 

 

 

NOTE: THESE DIMENSIONS ARE FOR FINISHED HOLE SIZE

13

Image 13
Contents Volt SH15 SH20 Hazardous Duty Room Air ConditionerTable of Contents Clean the filter frequently See General Maintenance Filter Information Maintenance ChecklistFunction Control Power Hazardgard Special FeaturesTemperature Control Control PanelGroups Models SH15 and SH20 Electrical RequirementsAccessory Detail Hazardgard Window Mount Installation HardwareUnpacking The Unit Chassis Wiring and PreparationProvided Hardware Before Shell Cabinet PreparationShell Cabinet Installation Standard Sash Windows Shell Installation Sash Window InstallationsTypical Installation Sill Plate Section B B Section a aWall Preparation Shell Installation Through-the-wall InstallationsSpecial Instructions For Extra Thick Walls Hole Size RequirementsBrick Veneer Construction Frame Wall ConstructionSolid Masonry Screw #12A X 2 Long Typical InstallationStep Chassis InstallationDetail Hazardgard Room AIR Conditioners Limited Warranty Instrucciones de Instalacion y Funcionamiento Instrucciones Para Uso Y Mantenimiento Tabla De ContenidosInstrucciones Para La Instalacion Instrucciones Generales Lista De Control Para El Mantenimiento Informacion Sobre El FiltroPanel De Control Caracteristicas Especiales Del HazardgardControl De Encendido Electricidad Control De La Temperatura¡Exclusiva Requerimientos Electricos Modelos SH15 y SH20Grupos Tamaño DEL Gabinete Número Descripción Cantidad De item Lista DE AccesoriosPreparacion y Instalacion Electrica Del Chasis Desempaque de la unidadHerramienta QUE SE Suministra Antesdespues Si la instalacion se hace a traves de la paredFigura D Instalacion Tipica Del Filo Del Antepecho Figura G Nota Estas SON LAS Dimensiones DEL Hueco Terminado Dimension Chasis Terminada Pequeño MedianoPreparacion De La Pared Instrucciones Especiales Para Paredes Extra GruesasMarco DE LA Pared Construccion EN ELConstruccion EN Paredes DE LadrilloInstalacion Tipica Paso Instalacion Del ChasisDetalle Figura QPage Instructions d’installation et d’utilisation Table Des Matières Instructions D’installation920-024-05 Dépannage Commande De Fonction Mise En Marche Panneau De CommandeCommande De Température Caractéristiques Spéciales Des Appareils HazardgardExclusivité Alimentation Électrique Modèles SH 15 et SHGroupes Détail DES Accessoires Branchement Du Châssis Et Préparation Déballage De L’appareilQuincaillerie Fournie Installation à travers un mur Installation dans une fenêtre à guillotinePréparation De L’enveloppe Avant AprèsPatte DE Support RÉF Installation de l’enveloppe fenêtre à guillotine standardInstallation Typique De La Plaque De Seuil Coupe B B Dimensions Finies DE L’OUVERTURE Installation De Lenveloppe Installation À Travers Un MurPréparation Du Mur Construction Avec Construction Avec UN Cadre EN BoisBoulon DE Scellement Installation TypiqueInstallation Du Châssis Détail Garantie Limite DUN AN Climatiseurs Hazardgard Friedrich
Related manuals
Manual 60 pages 10.39 Kb Manual 60 pages 9.21 Kb

SH20, SH15 specifications

The Friedrich SH15 and SH20 models are exemplary representatives of advanced heating solutions, designed to address the diverse needs in residential and commercial environments. Engineered with a focus on efficiency, performance, and user-friendliness, these heating systems make a strong case for modern heating technology.

One of the standout features of both the SH15 and SH20 is their energy efficiency. These models utilize state-of-the-art heat pump technology, which allows them to extract heat from the environment even in colder temperatures. This results in significantly lower energy consumption compared to traditional heating systems, leading to reduced utility bills and a lower carbon footprint. The SH15 is designed for smaller spaces, while the SH20 offers a bit more power, making it suitable for larger areas or homes with greater heating demands.

Both models incorporate advanced inverter technology, which adjusts the compressor speed depending on the heating requirements. This ensures that the units operate at optimal efficiency, providing consistent temperature control while minimizing energy waste. Inverter-driven systems contribute to quieter operation as well, which is ideal for residential settings where noise can be a concern.

User-friendliness is another hallmark of the Friedrich SH15 and SH20. Equipped with intuitive digital controls, users can easily set their preferred temperatures and schedules, allowing for personalized comfort. Moreover, both models support smart home integration, enabling remote access and control through mobile applications. This feature not only enhances convenience but also allows users to monitor energy usage and make adjustments on the fly.

Durability is a key characteristic of these heating systems. Constructed with high-quality materials, the SH15 and SH20 are designed to withstand harsh environmental conditions, ensuring long-lasting performance. They also feature advanced air filtration systems that improve indoor air quality by effectively removing allergens and other pollutants.

In summary, the Friedrich SH15 and SH20 embody the cutting-edge of heating technology, offering powerful, efficient, and user-friendly solutions for diverse heating needs. With their advanced features, smart technology integration, and robust construction, these models are well-suited for modern living, ensuring comfortable and environmentally responsible heating year-round.