Lincoln Electric IM700-D manual Diagram

Page 51

COMMANDER 300/ LN-25 WITH L431, K433 & K432-"L" OPTION

CONNECTION DIAGRAM

 

WARNING

Do not operate with panels open.

Keep guards in place.

Disconnect NEGATIVE (-) BATTERY LEAD

Keep away from moving parts.

before servicing.

Only qualified personnel should install,use

Do not touch electrically live parts.

or service this equipment.

CONNECTION

F-13

DIAGRAM:

 

COMMANDER 300

WORK

ELECTRODE

TO WORK

14PIN AMPHENOL

K867 UNIVERSAL

ADAPTER PLUG

ELECTRODE CABLE

SPARE 82 81 42 41 21

31

32

2

4

GND

75

76

77

}N.D.

31

32

2

4 GND

 

75

}

76

77

 

N.E.

 

K433

K432-"L" CABLE

LN-25

WIRE FEEDER WITH K431 OPTION

DIAGRAMS

N.A. WELDING CABLE MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.B. DIAGRAM SHOWS ELECTRODE POSTIVE. TO CHANGE POLARITY, TURN POWER "OFF".

REVERSE ELECTRODE AND WORK CABLES AT POWER SOURCE, SWITCH LN-25 POLARITY SWITCH. N.C. MOUNT K433 TO ENGINE WELDER PER INSTRUCTIONS PACKAGED WITH K433.

N.D. INSULATE EACH UNUSED LEADS INDIVIDUALLY.

N.E. SPLICE LEADS AND INSULATE.

A

S23993

F-13

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Safety Depends on You CommanderCalifornia Proposition 65 Warnings SafetyElectric Shock can kill Iii Welding Sparks can cause fire or explosionSûreté Pour Soudage a L’Arc Précautions DE SûretéThank You Table of Contents Section F Section CSection D Section EInstallation Safety PrecautionsLocation / Ventilation Vehicle Mounting LiftingHigh Altitude Operation TowingFuel USE Diesel Fuel only PRE-OPERATION Engine ServiceEngine Cooling System Battery Connection OILRemote Control High Frequency Generators for TIG ApplicationsWelding Terminals Duty Cycle Welding Output Volts at Rated Amps Welding Range Open Circuit Voltage Auxiliary Power1HEIGHT2 Width Depth Weight Bore x StrokeMachine Grounding Auxiliary Power ReceptaclesStandby Power Connections Welding Output CablesPower Connection of Lincoln Electric Wire Feeders Connection of the LN-25 to the CommanderConnection of LN-7 or LN-8 to the Commander Connection of LN-15 to the COM- Mander Across-The-Arc ModelControl Cable Model General Description Safety InstructionsDesign Features and Advantages OperationWelding Capability For Auxiliary PowerOther Features K1585-1 Commander 300 Standard ModelFuel Level Gauge and Light Controls and SettingsRUN- Stop Switch Start Push ButtonIdler Switch Engine Alternator Ammeter K1585Hour Meter Auxiliary Power Controls Engine Operation Starting the EngineStopping the Engine Stick Welding Welder OperationBREAK-IN Period Typical Fuel ConsumptionConstant Current CC Welding TIG WeldingTable B.3 Typical Current Ranges 1 for Tungsten ELECTRODES2 Commander 300 Settings When Using the K799 HI-FREQ UnitARC Gouging Electrode Current Range DiameterParalleling Simultaneous Welding and AUXIL- Iary Power Loads Auxiliary Power OperationOptional Field Installed Accessories AccessoriesRecommended Optional Equipment Maintenance Routine and Periodic MaintenanceEngine Maintenance Cooling System Cooling Blower Belt Fuel FiltersWelder / Generator Maintenance Nameplates / Warning Decals MaintenanceMake Part Number Table D.1 Engine Maintenance ComponentsHOW to USE Troubleshooting Guide TroubleshootingPossible Areas Symptoms Misadjustments Course of ActionFunction Problems Output Problems Diagrams Commander 300 Wiring Diagram for Codes 10871 and belowCommander 300 Wiring Diagram for Codes 10871 and Above Commander 300 Wiring Diagram for Codes 10950 Commander 300 Wiring Diagram for Codes 11200 and Above Connection Diagram DIAGRAMSF-5Diagram Commander Commander / K867 / K775 / LN-7 Connection DiagramDIAGRAMSF-7 DIAGRAMSF-8 Commander / K867 / LN-8 Connection Diagram DIAGRAMSF-10 DIAGRAMSF-11 S24787-6 DiagramDiagram DIAGRAMSF-14 DIAGRAMSF-15 DIAGRAMSF-16 24.79 Dimension PrintCommander Commander Precaucion Aviso DE
Top Page Image Contents