Lincoln Electric IM700-D manual Diagram, S24787-6

Page 50

ENGINE WELDERS LN/-8CONNECTION DIAGRAM

WARNING

CONNECTION

F-12

ELECTRIC SHOCK can kill

Do not operate with panels open.

Disconnect NEGATIVE (-) Battery lead

before servicing.

Do not touch electrically live parts.

MOVING PARTS can injure

Keep guards in place.

Keep away from moving parts. Only qualified personnel should install,use or service this equipment.

DIAGRAM:

COMMANDER 300

14 PIN AMPHENOL

+ _

CAUTION

TO NL-8NPUTI

CABLE PLUG

K595CONTROLCABLE

TOWORK

ELECTRODE CABLE

TOWIRE FEED UNIT

DIAGRAMS

ANY INCREASE OF THE HIGH IDLE ENGINE RPM BY CHANGING THE GOVERNOR SETTING OR OVERRIDING THE THROTTLE LINKAGE AN INCREASE IN THE AC WIRE FEEDER VOLTAGE, WHICH CAN DAMAGE THE CONTROL CIRCUIT. THE ENGINE GOVERNOR SETTING AT THE FACTORY — DO NOT ADJUST ABOVE RPM SPECIFICATIONS LISTED IN THE ENGINE WELDER OPERATING MANUAL.

N.A. WELDING CABLES MUST BE OF PROPER CAPACITY FOR THE CURRENT AND DUTY CYCLE OF IMMEDIATE AND FUTURE APPLICATIONS. SEE OPERATING MANUAL.

N.B. CONNECT WELDING CABLES TO OUTPUT STUDS FOR DESIRED POLARITY. POSITION THE WIRE FEEDER VOLTMETER SWITC MATCH THE POLARITY OF THE ELECTRODE CABLE.

N.C. PLACE IDLER SWITCH IN HIGH POSITION.

4-14-2000

S24787-6

F-12

Image 50

Contents Commander Safety Depends on YouSafety California Proposition 65 WarningsElectric Shock can kill Welding Sparks can cause fire or explosion IiiPrécautions DE Sûreté Sûreté Pour Soudage a L’ArcThank You Table of Contents Section E Section CSection D Section FLocation / Ventilation InstallationSafety Precautions Towing LiftingHigh Altitude Operation Vehicle MountingOIL PRE-OPERATION Engine ServiceEngine Cooling System Battery Connection Fuel USE Diesel Fuel onlyWelding Terminals Remote ControlHigh Frequency Generators for TIG Applications Bore x Stroke Welding Range Open Circuit Voltage Auxiliary Power1HEIGHT2 Width Depth Weight Duty Cycle Welding Output Volts at Rated AmpsWelding Output Cables Auxiliary Power ReceptaclesStandby Power Connections Machine GroundingPower Connection of LN-7 or LN-8 to the Commander Connection of Lincoln Electric Wire FeedersConnection of the LN-25 to the Commander Control Cable Model Connection of LN-15 to the COM- ManderAcross-The-Arc Model Operation Safety InstructionsDesign Features and Advantages General DescriptionK1585-1 Commander 300 Standard Model For Auxiliary PowerOther Features Welding CapabilityStart Push Button Controls and SettingsRUN- Stop Switch Fuel Level Gauge and LightHour Meter Idler SwitchEngine Alternator Ammeter K1585 Auxiliary Power Controls Stopping the Engine Engine OperationStarting the Engine Typical Fuel Consumption Welder OperationBREAK-IN Period Stick WeldingTIG Welding Constant Current CC WeldingCommander 300 Settings When Using the K799 HI-FREQ Unit Table B.3 Typical Current Ranges 1 for Tungsten ELECTRODES2Paralleling ARC GougingElectrode Current Range Diameter Auxiliary Power Operation Simultaneous Welding and AUXIL- Iary Power LoadsAccessories Optional Field Installed AccessoriesRecommended Optional Equipment Engine Maintenance MaintenanceRoutine and Periodic Maintenance Fuel Filters Cooling System Cooling Blower BeltNameplates / Warning Decals Maintenance Welder / Generator MaintenanceTable D.1 Engine Maintenance Components Make Part NumberTroubleshooting HOW to USE Troubleshooting GuideSymptoms Misadjustments Course of Action Possible AreasFunction Problems Output Problems Commander 300 Wiring Diagram for Codes 10871 and below DiagramsCommander 300 Wiring Diagram for Codes 10871 and Above Commander 300 Wiring Diagram for Codes 10950 Commander 300 Wiring Diagram for Codes 11200 and Above DIAGRAMSF-5 Connection DiagramCommander / K867 / K775 / LN-7 Connection Diagram Diagram CommanderDIAGRAMSF-7 DIAGRAMSF-8 Commander / K867 / LN-8 Connection Diagram DIAGRAMSF-10 DIAGRAMSF-11 Diagram S24787-6Diagram DIAGRAMSF-14 DIAGRAMSF-15 DIAGRAMSF-16 Dimension Print 24.79Commander Commander Precaucion Aviso DE