Skil Official Manual for Router Assembly and Safety Tips
Page 9

SM 1619X04663 05-11:SM 1619X04663 05-11 5/3/11 8:14 AM Page 9

Assembly

A wide assortment of router bits with different profiles is available separately.

To prevent personal injury, ! WARNING always remove the plug

from power source before removing or installing bits or accessories.

INSTALLING A ROUTER BIT

Place router upside down with the top of the router resting on the bench. Another option is to remove the motor from the base before installing the bit.

1.Remove the chip shield.

2.Press collet lock to stop rotation of armature shaft. NOTE: it may be necessary to rotate collet chuck assembly to engage collet lock (Fig. 5).

3.Next, use the collet wrench to loosen the collet nut in counter-clockwise direction (viewed from under the router).

4.Insert the shank of the router bit into the collet chuck assembly as far as it will go, then back the shank out until the cutters are approximately 1/8" to 1/4" away from the collet nut face.

5.With the router bit inserted and the collet lock holding the armature shaft, use the

collet wrench to firmly tighten the collet nut in a clockwise direction (viewed from under the router). To ensure proper gripping of the router bit, the shank of the router bit must be inserted at least 5/8" into collet.

!WARNING When the templet guide has been removed from

base, do not use router bits greater than 2" in diameter as they will not fit through the sub-base.

 

! CAUTION

To prevent damage to tool,

 

 

do not tighten collet nut

without a bit.

 

NOTE: The router bit shank and collet chuck should be clean and free of dust, wood, residue and grease before assembling.

REMOVING THE ROUTER BIT

1.Press collet lock to stop rotation of armature shaft and turn the collet chuck assembly in a counter-clockwise direction.

2.Once the collet chuck assembly is loosened continue to turn the collet chuck assembly until it pulls the collet free from its taper, and the router bit can be removed.

NOTE: The collet chuck is self-extracting; it is NOT necessary to strike the collet chuck to free the router bit.

1/4" BIT

SHANK

COLLET LOCK

FIG. 5

COLLET

COLLET NUT

BASE

WRENCH

-9-

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Leer antes de usar Call Toll Free forSee Voir Ver la página Work area safety General Power Tool Safety WarningsElectrical safety Personal safetyService Safety Rules for RoutersAdditional Safety Warnings Symbol Name Designation/Explanation SymbolsCertified to Conforms toUL Standard CAN/CSA Standard C22.2 NoFunctional Description and Specifications Disconnect the plug from the power source before making anyFix Base Router Plunge Base Router Fine Adjustment Variable Speed DialModel 1827 & 1830 only Base Clamp Lever Collet Lock SUB-BASEInstalling a Router BIT AssemblyRemoving the Router BIT Shank Collet Lock Collet NUT Base WrenchCollet Chuck Care Collet Chuck AssemblyTemplate Guide Adapter Not included, available as accessory InstallingDepth Adjustment with Fixed Base Fine Adjustment Knob Operating InstructionsDepth Adjustment with Plunge Base Plunging Action Fine Adjustment Knob Indicator Ring Depth ScaleDepth ROD and Turret Electronic Variable Speed Control Dial Setting RPM ApplicationSITE-LIGHT Feeding the RouterBoard Guide Securely Clamp Guiding the RouterAttaching Guide Work BaseTemplate Guides Not included, available as accessoryRouter Collet NUT Template Router Guide SUB-BASE Pattern OffsetMaintenance Accessories CleaningExtension Cords Trouble Shooting Problem Trouble Tool will not StartTrouble Tool does not Come UP to Speed Sécurité électrique Sécurité du lieu de travailRègles de sécurité concernant les toupies Utilisation et entretien des outils ÉlectroportatifsEntretien Loutil, causant éventuellement un bris de la lame Avertissements supplémentaires concernant la sécuritéSymbole Nom Désignation/Explication SymbolesConforme à Symboles suiteCertifié conforme à Norme ULDescription fonctionnelle et spécifications Défonceuse à embase fixeEmbase DE Type a Défonceuse à embase plongeante Position Slide ON/OFF Switch Poignée Index DE ProfondeurPoignée Embase DE Type B Levier DE Serrage DE L’EMBASE LA DouilleAssemblage Installation D’UN FER DE DéfonceuseDémontage DU FER DE Défonceuse Queue Blocage DE LA Douille Écrou DE Douille Embase CLÉEntretien DU MANDRIN-DOUILLE Ensemble DE MANDRIN-DOUILLEÉcrou DE LA Douille Déflecteur À Copeaux Instructions d’utilisationDéflecteur Copeaux DE Réglage FIN DE L’EMBASE FixeDE Plongéede L’EMBASE Plongeante ’ACTION DE PlongéeTige DE Profondeur ET Tourelle Depart EN Douceur Commande Électronique DEApplication Éclairage SITE-LIGHTPlanche DE Guidage Bridez Fermement LA Planche Guidage DE LA DéfonceuseFixation DU Guide Pièce EmbaseFers Guidés PAR Roulement OU PAR Pilote Guides DE GabaritEntretien Accessoires Cordons de rallongeNettoyage Solutions Guide de diagnosticProblème L’OUTIL NE Démarre PAS Problème L’OUTIL NE Tourne PAS À UNE Vitesse SuffisanteSeguridad del área de trabajo Seguridad eléctricaSeguridad personal Normas de seguridad para fresadoras MecánicasServicio de ajustes y reparaciones Advertencias de seguridad adicionales Símbolo Nombre Designación/explicación SímbolosCumple con las siguientes Normas Símbolos continuaciónCertificado conforme a las Siguientes normas Estándar ULFresadora de base fija Descripción funcional y especificacionesPomo DE Ajuste Fino Fresadora de descenso verticalRemoción DE LA Broca DE Fresadora EnsamblajeBroca DE 1/4 Cuerpo Llave DE TuercaConjunto DE Mandril Portaherramienta Cierre DEL Portaherramienta Base FijaDescenso Vertical Palanca Fijación DE LA Base Instalación DEL Instrucciones de funcionamientoDeflector DE Virutas Está diseñado para utilizarse como protector de seguridadProfundidad DE Penetración Palanca DE Fijación DE LA ProfundidadVarilla DE Profundidad Y Torreta DE Pomo DEDispositivo DE Arranque Suave Apagado DE 2 PosicionesAplicación DEL DialColocación DE LA Guía Guiado DE LA FresadoraCorte AnchuraCorte EL Piloto SE Desliza Brocas CON Punta Piloto Y CON Guía DE CojineteParte PlantillasServicio MantenimientoAccesorios Cordones de extensiónLimpieza Para EvitarAvería LA Herramienta no Arranca Resolución de problemasRemedio Avería LA Herramienta no Alcanza Toda SU VelocidadSM 1619X04663 05-11SM 1619X04663 05-11 5/3/11 815 AM Remarques Notas 1619X04663

1827, 1817, 1830 specifications

Skil is a renowned brand in the power tool industry, offering a range of products that cater to the needs of both professionals and DIY enthusiasts. Among its impressive lineup, the Skil 1830, 1817, and 1827 models stand out for their unique features and versatile capabilities, making them essential tools for a variety of applications.

The Skil 1830 is a highly efficient reciprocating saw designed for both heavy-duty tasks and intricate cutting jobs. One of its standout features is the Variable Speed Control, which allows users to adjust the speed according to the material being cut. This feature ensures maximum precision and control, whether working with wood, metal, or plastic. The 1830 also comes equipped with a tool-less blade change system, making it easy to switch blades quickly and efficiently. Its powerful motor ensures optimal performance, while the ergonomic handle provides comfort during extended use.

On the other hand, the Skil 1817 is a versatile circular saw that is perfect for both beginners and seasoned pros. Its powerful 15-amp motor delivers impressive cutting performance, enabling users to easily tackle a variety of materials. One of the most notable aspects of the 1817 is its laser guide system, which enhances accuracy and precision when making straight cuts. Additionally, the integrated dust blower keeps the cutting line clear for improved visibility, while the lightweight design of the saw allows for easy maneuverability without sacrificing power.

Lastly, the Skil 1827 is a robust and reliable jigsaw that excels in making curved and intricate cuts. Its orbital cut option allows users to switch between a pendulum action for fast cuts and a straight cut for finer details. The 1827 features a variable speed dial that can be adjusted based on the material, ensuring optimal performance for every job. An integrated blower keeps the cutting line free of debris, enhancing visibility and accuracy. Its ergonomic grip ensures comfort during extended use, and the tool-less blade change feature allows for quick and easy blade swaps.

In summary, the Skil 1830, 1817, and 1827 power tools offer a range of features and technologies that cater to various cutting needs. From the adjustable speed and tool-less blade changes of the 1830 to the laser guide of the 1817 and the orbital cutting options of the 1827, each model is designed with the user in mind, ensuring ease of use, comfort, and precision. Whether working on a professional project or a home improvement task, these Skil tools provide the reliability and performance needed to achieve excellent results.
Top Page Image Contents