Skil 2510 manual Inserting Bits, Removing Chuck, Chuck Sleeve Clockwise Counter, Installing Chuck

Page 10

SM 1619X01949 06-07 6/29/07 12:20 PM Page 10

INSERTING BITS

Move reverse switch lever to the center “OFF” position. Remove battery pack and rotate the

clutch ring to the drill bit symbol “ ”. Rotate the chuck sleeve counter-clockwise viewing from chuck end, and open chuck to approximate drill bit diameter. Insert a clean bit up to the drill bit flutes for small bits, or as far as it will go for large bits. Close chuck by rotating the chuck sleeve clockwise and securely tighten by hand (Fig. 4).

!Do not use the power of WARNING the drill while grasping

chuck to loosen or tighten bit. Friction burn or hand injury is possible if attempting to grasp the spinning chuck.

REMOVING CHUCK

Rotate the clutch ring to the drill bit

symbol “ ”. Open the chuck all the way, remove left-hand thread screw inside chuck by turning it clockwise. Insert the short arm of

FIG. 4

CHUCK SLEEVE

CLOCKWISE

COUNTER

CLOCKWISE

a 3/8" hex key wrench and close jaws on flats of wrench. Strike long arm of wrench sharply counterclockwise, remove wrench and unthread chuck from spindle (Fig. 4).

INSTALLING CHUCK

Always keep the spindle threads, the threads of the chuck and securing screw free of debris. To install a chuck, reverse “removing the chuck” procedure.

RELEASING AND INSERTING BATTERY PACK FROM TOOL

Release battery pack from tool by pressing the battery release button and sliding pack out of handle base (Fig. 6). To insert battery, align

battery and slide battery pack into tool until it locks into position. Do not force.

IMPORTANT CHARGING NOTES

1.The charger was designed to fast charge the battery only when the battery temperature is between 32˚F (0˚C) and 113˚F (45˚C). If the battery pack is too hot or too cold, the charger will not fast charge the battery. (This may happen if the battery pack is hot from heavy use). When the battery temperature returns to between 32˚F (0˚C) and 113˚F (45˚C), the charger will automatically begin charging.

2.A substantial drop in operating time per charge may mean that the battery pack is nearing the end of its life and should be replaced.

3.Remember to unplug charger during storage period.

4.If battery does not charge properly:

a.Check for voltage at outlet by plugging in some other electrical device.

b.Check to see if outlet is connected to a light switch which turns power “off” when lights are turned off.

c.Check battery pack terminals for dirt. Clean with cotton swab and alcohol if necessary.

d.If you still do not get proper charging, take or send tool, battery pack and charger to your local Skil Service Center. See “Tools, Electric” in the Yellow Pages for names and addresses.

Note: Use of chargers or battery packs not sold by Skil will void the warranty.

-10-

Page 9 Page 11
Image 10
Page 9 Page 11
Contents For English Version Version française Read Before UsingSee Voir Ver la página Electrical safety General Safety RulesWork area safety Personal safetyService Power tool use and careBattery tool use and care Power tools are dangerous in the hands of untrained usersSafety Rules for Cordless Drills/Drivers Exposure to noise can cause hearing lossBattery Care Battery/ChargerNails, screws, keys, etc. Fire or injury may result Battery Disposal LITHIUM-ION BatteriesSymbols Lithium Ion Cordless Drill/Drivers Functional Description and SpecificationsNot Available on ALL Models Operating Instructions Inserting Bits Installing ChuckReleasing and Inserting Battery Pack from Tool Removing ChuckDo not use tool Charging Battery PackCharger Indicator Light While chargingOperating Tips Maintenance Cleaning AccessoriesCertain cleaning agents Caution and solvents damage Sécurité électrique Consignes générales de sécuritéSécurité du lieu de travail Sécurité personnelleUtilisation et entretien des outils à piles Utilisation et entretien des outils ÉlectroportatifsEntretien Consignes de sécurité pour perceuses/tournevis sans fil Le plomb provenant des peintures à base de plombEntretien des piles Chargeur de pilePas dans l’outil ou le Piles LITHIUM-ION Mise au rebut des pilesNe tentez pas de Robert Bosch Tool Corporation participe volontairementSymboles Perceuses/visseuses sans fil à piles au lithium-ion Éclairage ’APPOINT Powerlight BLOC-PILESDescription fonctionnelle et spécifications NON Disponible SUR Tous LES ModèlesConsignes de fonctionnement Sens Horaire ANTI-HORAIRE Pose DU Mandrin Insertion DES ForetsRetrait DU Mandrin Retrait ET Insertion DU BLOC-PILES Dans LoutilQuil est en charge Chargement DU BLOC-PILESBLOC-PILES Chargeur Chargeur Témon LumineuxConsignes de fonctionnement Entretien Certains Agents AccessoiresNettoyage Et certainsSeguridad eléctrica Normas generales de seguridadSeguridad del área de trabajo Seguridad personalUso y cuidado de las herramientas Alimentadas por baterías MecánicasServicio de ajustes y reparaciones SM 1619X01949 06-07 6/29/07 1220 PM Batería/cargador Cuidado de las bateríasEliminación de las baterías Baterías DE Iones DE LitioCon aislamiento doble SímbolosDe Li-ion No Disponible EN Todos LOS Modelos LUZ Powerlight Paquete DE Baterías LUZ IndicadoraDescripción funcional y especificaciones Paquete de bateriasInstrucciones de funcionamiento Sentido DE LAS Agujas DEL Reloj Contrario AL Colocacion DE LAS BrocasDesmontaje DEL Mandril Instalacion DEL MandrilEl paquete de baterías Carga DEL Paquete DE BateríasNo use la herramienta Cargador LUZ IndicadoraConsejos de funcionamiento Mantenimiento ServicioCordones de extensión AccesoriosLimpieza Para evitarSM 1619X01949 06-07 6/29/07 1220 PM Remarques Notas SM 1619X01949 06-07 6/29/07 1220 PM

2510 specifications

The Skil 2510, a versatile and powerful tool, is designed to meet the demands of both amateur DIY enthusiasts and seasoned professionals. Known for its high performance and practical features, the Skil 2510 is a go-to choice for those in need of a reliable and efficient solution for various woodworking tasks.

A standout feature of the Skil 2510 is its robust 7.0-amp motor, which delivers ample power to handle a wide range of cutting applications. This motor ensures that project execution is smooth and efficient, whether cutting through hardwood, softwood, or laminate. Its capability to make quick and precise cuts contributes to improved productivity and exceptional results.

The Skil 2510 comes equipped with a variable speed control feature, allowing users to adjust the cutting speed according to the material being used. This flexibility is crucial in achieving optimal results, as different materials require different speeds for effective cutting. The tool's speed ranges from 3,000 to 3,800 RPM, making it suitable for both intricate cuts and rapid material removal.

Another significant aspect of the Skil 2510 is its cutting capacity. The saw features a 10-inch blade that can tackle a variety of cutting angles and bevels. The bevel capability reaches up to 45 degrees, enabling users to create precise miter cuts. This feature is particularly beneficial for projects that require refined edges and intricate details.

Safety is always a concern when operating power tools, and the Skil 2510 addresses this with various safety features. The integrated blade guard protects users from accidental injuries while the saw is in operation. Additionally, the electric brake technology stops the blade quickly after the trigger is released, minimizing the risk of accidents.

The design of the Skil 2510 also prioritizes user comfort and ease of use. The lightweight construction allows for easy maneuverability during extended use, reducing user fatigue. The ergonomic handle ensures a firm grip, promoting better control and accuracy while cutting.

Incorporating innovative technologies and features, the Skil 2510 stands out as a powerful and versatile solution for woodworking projects. With its combination of performance, safety, and user-friendly design, this tool is an excellent addition to any workshop, making it easier for users to achieve professional-grade results.
Top Page Image Contents