Hitachi SJ700-2 Series service manual Fef Fuf

					Default
	Code	Function name	Monitored data or setting				Note
				_FF	_FEF	_FUF
	C001	Terminal [1] function (*2)	01 (RV: Reverse RUN), 02 (CF1: Multispeed 1 setting), 03 (CF2: Multispeed 2		18
			setting), 04 (CF3: Multispeed 3 setting), 05 (CF4: Multispeed 4 setting), 06 (JG:		(*2)
			Jogging), 07 (DB: external DC braking), 08 (SET: Set 2nd motor data), 09 (2CH:
	C002	Terminal [2] function			16
			2-stage acceleration/deceleration), 11 (FRS: free-run stop), 12 (EXT: external trip),
	C003	Terminal [3] function (*2)	13 (USP: unattended start protection), 14: (CS: commercial power source enable),		06
			15 (SFT: software lock), 16 (AT: analog input voltage/current select), 17 (SET3: 3rd		(*2)
			motor control), 18 (RS: reset), 20 (STA: starting by 3-wire input), 21 (STP: stopping
	C004	Terminal [4] function			11
			by 3-wire input), 22 (F/R: forward/reverse switching by 3-wire input), 23 (PID: PID
	C005	Terminal [5] function			09
			disable), 24 (PIDC: PID reset), 26 (CAS: control gain setting), 27 (UP: remote
	C006	Terminal [6] function	control UP function), 28 (DWN: remote control DOWN function), 29 (DWN: remote	03	03	13
			control data clearing), 31 (OPE: forcible operation), 32 (SF1: multispeed bit 1), 33
	C007	Terminal [7] function			02
			(SF2: multispeed bit 2), 34 (SF3: multispeed bit 3), 35 (SF4: multispeed bit 4), 36
			(SF5: multispeed bit 5), 37 (SF6: multispeed bit 6), 38 (SF7: multispeed bit 7), 39
			(OLR: overload restriction selection), 40 (TL: torque limit enable), 41 (TRQ1: torque
			limit selection bit 1), 42 (TRQ2: torque limit selection bit 2), 43 (PPI: P/PI mode
			selection), 44 (BOK: braking confirmation), 45 (ORT: orientation), 46 (LAC: LAD
terminals			cancellation), 47 (PCLR: clearance of position deviation), 48 (STAT: pulse train
			position command input enable), 50 (ADD: trigger for frequency addition [A145]), 51
			(F-TM: forcible-terminal operation), 52 (ATR: permission of torque command input),
			53 (KHC: cumulative power clearance), 54 (SON: servo-on), 55 (FOC: forcing), 56
			(MI1: general-purpose input 1), 57 (MI2: general-purpose input 2), 58 (MI3:
input	C008	Terminal [8] function			01
			general-purpose input 3), 59 (MI4: general-purpose input 4), 60 (MI5:
			general-purpose input 5), 61 (MI6: general-purpose input 6), 62 (MI7:
Intelligent
			general-purpose input 7), 63 (MI8: general-purpose input 8), 65 (AHD: analog
			command holding), 66 (CP1: multistage position settings selection 1 ), 67 (CP2:
			multistage position settings selection 2), 68 (CP3: multistage position settings
			selection 3), 69 (ORL: Zero-return limit function), 70 (ORG: Zero-return trigger
			function), 71 (FOT: forward drive stop), 72 (ROT: reverse drive stop), 73 (SPD:
			speed / position switching), 74 (PCNT: pulse counter), 75 (PCC: pulse counter
			clear), no (NO: no assignment)
	C011	Terminal [1] active state	00 (NO) / 01 (NC)		00
	C012	Terminal [2] active state	00 (NO) / 01 (NC)		00
	C013	Terminal [3] active state	00 (NO) / 01 (NC)		00
	C014	Terminal [4] active state	00 (NO) / 01 (NC)		00
	C015	Terminal [5] active state	00 (NO) / 01 (NC)		00
	C016	Terminal [6] active state	00 (NO) / 01 (NC)		00
	C017	Terminal [7] active state	00 (NO) / 01 (NC)		00
	C018	Terminal [8] active state	00 (NO) / 01 (NC)		00
	C019	Terminal [FW] active state	00 (NO) / 01 (NC)		00

1 - 10